alx / reprap-arduino-firmware

//
// Start of temperature lookup table
//
// Thermistor lookup table for RepRap Temperature Sensor Boards (http://make.rrrf.org/ts)
// Made with createTemperatureLookup.py (http://svn.reprap.org/trunk/reprap/firmware/Arduino/utilities/createTemperatureLookup.py)
// ./createTemperatureLookup.py --r0=100000 --t0=25 --r1=0 --r2=4700 --beta=4066 --max-adc=1023
// r0: 100000
// t0: 25
// r1: 0
// r2: 4700
// beta: 4066
// max adc: 1023
#define NUMTEMPS 20
short temptable[NUMTEMPS][2] = {
   {1, 841},
   {54, 255},
   {107, 209},
   {160, 184},
   {213, 166},
   {266, 153},
   {319, 142},
   {372, 132},
   {425, 124},
   {478, 116},
   {531, 108},
   {584, 101},
   {637, 93},
   {690, 86},
   {743, 78},
   {796, 70},
   {849, 61},
   {902, 50},
   {955, 34},
   {1008, 3}
};
//
// End of temperature lookup table
//
 
#define EXTRUDER_FORWARD true
#define EXTRUDER_REVERSE false
 
//these our the default values for the extruder.
int extruder_target_celsius = 0;
int extruder_max_celsius = 0;
byte extruder_heater_low = 64;
byte extruder_heater_high = 255;
 
//this is for doing encoder based extruder control
volatile bool extruder_direction = EXTRUDER_FORWARD;
volatile int extruder_error = 0;
 
//these keep track of extruder speed, etc.
int extruder_rpm = 0;
long extruder_delay = 0;
 
//for our closed loop control
int last_extruder_error = 0;
int last_extruder_delta = 0;
int last_extruder_speed = 0;
 
void extruder_read_quadrature()
{  
  // found a low-to-high on channel A
  if (digitalRead(EXTRUDER_ENCODER_A_PIN) == HIGH)
  {   
    // check channel B to see which way
    if (digitalRead(EXTRUDER_ENCODER_B_PIN) == LOW)
    {
      if (INVERT_QUADRATURE)
        extruder_error--; 
      else
        extruder_error++;
    }
    else
    {
      if (INVERT_QUADRATURE)
        extruder_error++;
      else
        extruder_error--;
    }  
  }
  // found a high-to-low on channel A
  else                                        
  {
    // check channel B to see which way
    if (digitalRead(EXTRUDER_ENCODER_B_PIN) == LOW)
    {
      if (INVERT_QUADRATURE)
        extruder_error++;
      else
        extruder_error--;
    }
    else
    {
      if (INVERT_QUADRATURE)
        extruder_error--;
      else
        extruder_error++;
    }  
  }
}
 
void init_extruder()
{
	//default to room temp.
	extruder_set_temperature(21);
 
	//setup our pins
	pinMode(EXTRUDER_MOTOR_DIR_PIN, OUTPUT);
	pinMode(EXTRUDER_MOTOR_SPEED_PIN, OUTPUT);
	pinMode(EXTRUDER_HEATER_PIN, OUTPUT);
	pinMode(EXTRUDER_FAN_PIN, OUTPUT);
 
	//initialize values
	digitalWrite(EXTRUDER_MOTOR_DIR_PIN, EXTRUDER_FORWARD);
	analogWrite(EXTRUDER_FAN_PIN, 0);
	analogWrite(EXTRUDER_HEATER_PIN, 0);
	analogWrite(EXTRUDER_MOTOR_SPEED_PIN, 0);
 
	//setup our encoder interrupt stuff.
	//these pins are inputs
	pinMode(EXTRUDER_ENCODER_A_PIN, INPUT);
	pinMode(EXTRUDER_ENCODER_B_PIN, INPUT);
 
	//turn on internal pullups
	digitalWrite(EXTRUDER_ENCODER_A_PIN, HIGH);
	digitalWrite(EXTRUDER_ENCODER_A_PIN, HIGH);
 
	//attach our interrupt handlers
	attachInterrupt(0, extruder_read_quadrature, CHANGE);
 
	//setup our timer interrupt stuff
	setupTimer1Interrupt();
	disableTimer1Interrupt();
}
 
void extruder_set_direction(bool direction)
{
	extruder_direction = direction;
}
 
void extruder_set_cooler(byte speed)
{
	analogWrite(EXTRUDER_FAN_PIN, speed);
}
 
void extruder_set_temperature(int temp)
{
	extruder_target_celsius = temp;
	extruder_max_celsius = (int)((float)temp * 1.1);
}
 
/**
*  Samples the temperature and converts it to degrees celsius.
*  Returns degrees celsius.
*/
int extruder_get_temperature()
{
	if (EXTRUDER_THERMISTOR_PIN > -1)
		return extruder_read_thermistor();
	else if (EXTRUDER_THERMOCOUPLE_PIN > -1)
		return extruder_read_thermocouple();
}
 
/*
* This function gives us the temperature from the thermistor in Celsius
*/
int extruder_read_thermistor()
{
	int raw = extruder_sample_temperature(EXTRUDER_THERMISTOR_PIN);
 
	int celsius = 0;
	byte i;
 
	for (i=1; i<NUMTEMPS; i++)
	{
		if (temptable[i][0] > raw)
		{
			celsius  = temptable[i-1][1] + 
				(raw - temptable[i-1][0]) * 
				(temptable[i][1] - temptable[i-1][1]) /
				(temptable[i][0] - temptable[i-1][0]);
 
			if (celsius > 255)
				celsius = 255; 
 
			break;
		}
	}
 
	// Overflow: We just clamp to 0 degrees celsius
	if (i == NUMTEMPS)
		celsius = 0;
 
	return celsius;
}
 
/*
* This function gives us the temperature from the thermocouple in Celsius
*/
int extruder_read_thermocouple()
{
	return ( 5.0 * extruder_sample_temperature(EXTRUDER_THERMOCOUPLE_PIN) * 100.0) / 1024.0;
}
 
/*
* This function gives us an averaged sample of the analog temperature pin.
*/
int extruder_sample_temperature(byte pin)
{
	int raw = 0;
 
	//read in a certain number of samples
	for (byte i=0; i<TEMPERATURE_SAMPLES; i++)
		raw += analogRead(pin);
 
	//average the samples
	raw = raw/TEMPERATURE_SAMPLES;
 
	//send it back.
	return raw;
}
 
void extruder_manage_speed()
{
	//is our speed changing?
	int extruder_error_delta = abs(last_extruder_error) - abs(extruder_error);
	int extruder_delta_delta = last_extruder_delta - extruder_error_delta;
	int extruder_error_factor = abs(extruder_error) / 2;
 
	//calculate our speed.
	int speed = 0;
	speed += extruder_error_factor;
        speed += last_extruder_speed / 2;
	speed += extruder_error_delta * 2;
	speed += extruder_delta_delta * 2;
       
        //why not average speeds?
        speed = (speed + last_extruder_speed) / 2;
 
	//do some bounds checking.
	speed = max(speed, EXTRUDER_MIN_SPEED);
	speed = min(speed, EXTRUDER_MAX_SPEED);
 
	//temporary debug stuff.
	if (false && random(500) == 1)
	{
		Serial.print("e:");
		Serial.print(extruder_error, DEC);
		Serial.print(" d:");
		Serial.print(extruder_error_delta, DEC);
		Serial.print(" dd:");
		Serial.print(extruder_delta_delta, DEC);
		Serial.print(" s:");
		Serial.println(speed);
	}
 
	//figure out which direction to move the motor
	if (extruder_error > 0)
		digitalWrite(EXTRUDER_MOTOR_DIR_PIN, EXTRUDER_REVERSE);
	else if (extruder_error < 0)
		digitalWrite(EXTRUDER_MOTOR_DIR_PIN, EXTRUDER_FORWARD);
 
	//send us off at that speed!
	if (abs(extruder_error) > EXTRUDER_ERROR_MARGIN)
		analogWrite(EXTRUDER_MOTOR_SPEED_PIN, speed);
	else
		analogWrite(EXTRUDER_MOTOR_SPEED_PIN, 0);
 
	//save our last error.
	last_extruder_error = extruder_error;
	last_extruder_delta = extruder_error_delta;
	last_extruder_speed = speed;
}
 
 
/*!
  Manages motor and heater based on measured temperature:
  o If temp is too low, don't start the motor
  o Adjust the heater power to keep the temperature at the target
 */
void extruder_manage_temperature()
{
	//make sure we know what our temp is.
	int current_celsius = extruder_get_temperature();
 
	//put the heater into high mode if we're not at our target.
	if (current_celsius < extruder_target_celsius)
		analogWrite(EXTRUDER_HEATER_PIN, extruder_heater_high);
	//put the heater on low if we're at our target.
	else if (current_celsius < extruder_max_celsius)
		analogWrite(EXTRUDER_HEATER_PIN, extruder_heater_low);
	//turn the heater off if we're above our max.
	else
		analogWrite(EXTRUDER_HEATER_PIN, 0);
 
	extruder_manage_speed();
}