diff --git a/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/Pyr0_Piezo_Sensor_V2.x.x.cpp b/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/Pyr0_Piezo_Sensor_V2.x.x.cpp
index 26bddca..4e7ec3f 100644
--- a/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/Pyr0_Piezo_Sensor_V2.x.x.cpp
+++ b/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/Pyr0_Piezo_Sensor_V2.x.x.cpp
@@ -45,7 +45,7 @@ You can also enable or disable DEBUG output with: DEBUG [0|1]
 You can query the current configuration with: CONFIG
 You can query the current state (including ADC measurements) with: STATE
 
-To reset all settings to defaults, use: RESET
+To set all settings to defaults, use: ERASE
 
 These commands should be wrapped in this format:
 CMD INT
diff --git a/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.cpp b/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.cpp
index 4c38f21..98edefe 100644
--- a/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.cpp
+++ b/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.cpp
@@ -11,9 +11,9 @@ int Debug = 0;
 long voltMeterConstant = VM_CONST_DEFAULT;
 uint8_t pP_i2c_address = 0xa0;
 
-void resetEEPROM() {
+void eraseEEPROM() {
 	
-	resetConfig();
+	setDefaultConfig();
 	
     EEPROM.put(GAIN_FACTOR_ADDRESS, GAIN_FACTOR);
     EEPROM.put(FOLLOWER_THRESHOLD_ADDRESS, followerThrs);
@@ -24,50 +24,50 @@ void resetEEPROM() {
     EEPROM.put(VM_CONST_ADDRESS, voltMeterConstant);
 }
 
-// Restore config from EEPROM, otherwise reset config and write to EEPROM
+// Restore config from EEPROM, otherwise erase config and write to EEPROM
 void restoreConfig() {
     int temp;
 	
-	bool reset = false;
+	bool erase = false;
 
     EEPROM.get(GAIN_FACTOR_ADDRESS, temp);
     if (temp < 0 || temp > 4) {
-		reset = true;
+		erase = true;
     } else {
         GAIN_FACTOR = temp;
     }
 
     EEPROM.get(FOLLOWER_THRESHOLD_ADDRESS, temp);
     if (temp < 0 || temp > 5000) {
-        reset = true;
+        erase = true;
     } else {
         followerThrs = temp;
     }
 
     EEPROM.get(COMP_THRESHOLD_ADDRESS, temp);
     if (temp < 0 || temp > 5000) {
-        reset = true;
+        erase = true;
     } else {
         compThrs = temp;
     }
 
     EEPROM.get(LOOP_DUR_ADDRESS, temp);
     if (temp < 0 && temp > 1000) {
-        reset = true;
+        erase = true;
     } else {
         LOOP_DUR = temp;
     }
 
     EEPROM.get(TRG_DUR_ADDRESS, temp);
     if (temp < 0 || temp > 1000) {
-        reset = true;
+        erase = true;
     } else {
         TRG_DUR = temp;
     }
 
     EEPROM.get(HYST_ADDRESS, temp);
     if (temp < 0 || temp > 1000) {
-        reset = true;
+        erase = true;
     } else {
         Hyst = temp;
     }
@@ -75,17 +75,17 @@ void restoreConfig() {
     long longTemp;
     EEPROM.get(VM_CONST_ADDRESS, longTemp);
     if (longTemp < 1000000L || longTemp > 1200000L) {
-        reset = true;
+        erase = true;
     } else {
         voltMeterConstant = longTemp;
     }
 	
-	if (reset) {
-		resetEEPROM();
+	if (erase) {
+		eraseEEPROM();
 	}
 }
 
-void resetConfig() {
+void setDefaultConfig() {
     GAIN_FACTOR = GAIN_FACTOR_DEFAULT;
     followerThrs = FOLLOWER_THRESHOLD_DEFAULT;
     compThrs = COMP_THRESHOLD_DEFAULT;
diff --git a/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.h b/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.h
index b5d57f1..9eb7dcc 100644
--- a/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.h
+++ b/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.h
@@ -60,8 +60,8 @@
   #endif
 #endif
 
-void resetEEPROM();
-void resetConfig();
+void eraseEEPROM();
+void setDefaultConfig();
 void restoreConfig();
 
 #endif
diff --git a/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_serial.h b/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_serial.h
index d5c6ab2..c5bb273 100644
--- a/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_serial.h
+++ b/firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_serial.h
@@ -222,8 +222,8 @@ void updateParams() {
   else if (strcmp(serialMessageIn, "CONFIG") == 0) {
     serialPrintConfig();
   }
-  else if (strcmp(serialMessageIn, "RESET") == 0) {
-    resetEEPROM();
+  else if (strcmp(serialMessageIn, "ERASE") == 0) {
+    eraseEEPROM();
     serialPrintConfig();
   }
   else if (strcmp(serialMessageIn, "STATE") == 0) {
@@ -238,7 +238,7 @@ void updateParams() {
     // Serial.println("To change ADC hysteresis value: HYST [integer]");
     // Serial.println("To enable or disable debug output: DEBUG [0|1]");
     // Serial.println("To print current config: CONFIG");
-    // Serial.println("To reset config to defaults: RESET");
+    // Serial.println("To set config to defaults: ERASE");
     // Serial.println("To print current state: STATE");
     // Serial.println("");
     // Serial.println("Commands are entered in this format:");