pymelcloud

This is a package for interacting with MELCloud and Mitsubishi Electric devices. It's still a little rough around the edges and the documentation is non-existent.

The goals for this package are:

To control and automate devices, not to configure them.
Handle device capabilities behind the scenes.
Make the different device types behave in predictable way.

Notes on usage

There are built-in rate limits and debouncing for most of the methods with the exception of the Device update method.

Initialize devices for each account only once during application runtime.
Make sure the update calls for each Device are rate limited. A 60 second update interval is a good starting point. Going much faster will exceed the expected load for MELCloud and can potentially cause availability issues.
Make absolutely sure the update calls are rate limited.

Supported devices

Air-to-air heat pumps (DeviceType=0)
Air-to-water heat pumps (DeviceType=1)
Energy Recovery Ventilators (DeviceType=3)

Read

Reads access only locally cached state. Call device.update() to fetch the latest state.

Available properties:

name
mac
serial
units - model info of related units.
temp_unit
last_seen
power
daily_energy_consumed
wifi_signal

Other properties are available through _ prefixed state objects if one has the time to go through the source.

Air-to-air heat pump properties

room_temperature
target_temperature
target_temperature_step
target_temperature_min
target_temperature_max
operation_mode
available operation_modes
fan_speed
available fan_speeds
vane_horizontal
available vane_horizontal_positions
vane_vertical
available vane_vertical_positions
total_energy_consumed in kWh. See notes below.

Air-to-water heat pump properties

tank_temperature
target_tank_temperature
tank_temperature_min
tank_temperature_max
outside_temperature
zones
- name
- status
- room_temperature
- target_temperature
status
operation_mode
available operation_modes

Energy recovery ventilator properties

room_temperature
outdoor_temperature
available fan_speeds
fan_speed
actual_supply_fan_speed
actual_exhaust_fan_speed
available ventilation_modes
ventilation_mode
actual_ventilation_mode
total_energy_consumed
wifi_signal
presets
error_code
core_maintenance_required
filter_maintenance_required
night_purge_mode
room_co2_level

Energy consumption

The energy consumption reading is a little strange. The API returns a value of 1.8e6 for my unit. Judging by the scale the unit is either kJ or Wh. However, neither of them quite fits.

Total reading in kJ matches better what I would expect based on the energy reports in MELCloud.
In Wh the reading is 3-5 times greater than what I would expect, but the reading is increasing at a rate that seems to match energy reports in MELCloud.

Here are couple of readings with monthly reported usage as reference:

2020-01-04T23:42:00+02:00 - 1820400, 28.5 kWh
2020-01-05T09:44:00+02:00 - 1821300, 29.4 kWh
2020-01-05T10:49:00+02:00 - 1821500, 29.6 kWh

I'd say it's pretty clear that it is Wh and the total reading is not reflective of unit lifetime energy consumption. total_energy_consumed converts Wh to kWh.

Write

Writes are applied after a debounce and update the local state once completed. The physical device does not register the changes immediately due to the 60 second polling interval.

Writable properties are:

power

Air-to-air heat pump write

target_temperature
operation_mode
fan_speed
vane_horizontal
vane_vertical

There's weird behavior associated with the horizontal vane swing. Toggling it on will also toggle vertical swing on and the horizontal swing has to be disabled before vertical vanes can be adjusted to any other position. This behavior can be replicated using the MELCloud user inteface.

Air-to-water heat pump write

target_tank_temperature
operation_mode
zone_1_target_temperature
zone_2_target_tempeature

Zone target temperatures can also be set via the Zone object returned by zones property on AtwDevice.

Energy recovery ventilator write

ventilation_mode
fan_speed

Example usage

import aiohttp
import asyncio
import pymelcloud


async def main():

    async with aiohttp.ClientSession() as session:
        # call the login method with the session
        token = await pymelcloud.login("my@example.com", "mysecretpassword", session=session)

        # lookup the device
        devices = await pymelcloud.get_devices(token, session=session)
        device = devices[pymelcloud.DEVICE_TYPE_ATW][0]

        # perform logic on the device
        await device.update()

        print(device.name)
        await session.close()

loop = asyncio.get_event_loop()
loop.run_until_complete(main())

License

erwindouna/python-melcloud

ErrorLooks like something went wrong!

About

Resources

License

Uh oh!

Stars

Watchers

Forks

Releases 1

Packages 0

Languages

Error
Looks like something went wrong!

Packages