ESP32_Display_Panel

!!!Notice!!!

This library has been archived. Please use the official Espressif library instead.

ESP32_Display_Panel is a versatile library designed to drive LCD and touch panels with ESP32. It is primarily developed for various Espressif development boards or custom boards.

ESP32_Display_Panel is based on Arduino-ESP32 (or ESP-IDF) and Espressif Components Registry, with various components encapsulated using C++.

Overview

The block diagram of ESP32_Display_Panel is shown in the figure below, mainly comprising the following features:

Supports Arduino-ESP32 and ESP-IDF SDKs.
Supports various Espressif development boards.
Supports custom boards.
Supports multiple types of drivers, including Bus, LCD, Touch, Backlight.

Dependent Libraries

The following table shows the versions of dependent libraries for ESP32_Display_Panel at different versions.

ESP32_Display_Panel	Arduino-ESP32	ESP-IDF	ESP32_IO_Expander
v1.x.x	>= v2.0.9	== v4.4.5	>= v1.1.0

Use with Arduino IDE

To use a library in Arduino IDE, please refer to the docs for IDE v1.x.x or the docs for IDE v2.x.x.

Examples

The examples folder contains various examples. To access them in the Arduino IDE, navigate to File -> Examples -> ESP32_Display_Panel. Each example sketch and README offer comprehensive usage instructions. Please review them before compiling.

Panel:
- Draw Color Bar: This example demonstrates how to draw simple color bar.
- Read Touch Point: This example demonstrates how to read touch point.
LVGL:
- Porting: This example demonstrates how to port LVGL(v8.3.x).

Detailed Usage

Here are the details of how to use ESP32_Display_panel.

Configure ESP32_Display_Panel

ESP32_Display_Panel has its own configuration file called ESP_Panel_Conf.h. When ESP32_Display_Panel is installed, follow these configuration steps:

Go to the directory of the installed Arduino libraries.
Go to the ESP32_Display_Panel folder, copy ESP_Panel_Conf_Template.h and place it out of ESP32_Display_Panel folder. It should be at the same level as the ESP32_Display_Panel folder. Then rename it as ESP_Panel_Conf.h.

Finally, the layout of the Arduino Libraries folder with ESP_Panel_Conf.h should look like this:

arduino
    |-libraries
        |-ESP32_Display_Panel
        |-other_lib_1
        |-other_lib_2
        |-ESP_Panel_Conf.h

Configure Supported Board

Please refer to the list of Supported Boards to verify whether the current board is compatible.

Open ESP_Panel_Conf.h and uncomment one of the following macros to select an supported development board. Taking ESP32_S3_BOX as an example:

```c
// #define ESP_PANEL_BOARD_ESP32_C3_LCDKIT
#define ESP_PANEL_BOARD_ESP32_S3_BOX
// #define ESP_PANEL_BOARD_ESP32_S3_BOX_LITE
```

After that, refer to Use Library to use the library in the sketch.

Configure Unsupported Board

Since ESP32_Display_Panel library can only utilize the internally supported LCD and Touch drivers, please ensure that the LCD, Touch, and required Bus for the custom board are present in the list of Supported Drivers.

Open ESP_Panel_Conf.h. Firstly, set the macro ESP_PANEL_USE_SUPPORTED_BOARD to 0, as below:

#define ESP_PANEL_USE_SUPPORTED_BOARD   (0)

After that, modify the values of other macros as needed. They represent parameters that can be adjusted for LCD, Touch, and other device initialization.

Here are some important macros for the LCD:

/* Set to 0 if not using LCD */
#define ESP_PANEL_USE_LCD           (0)

/**
 * LCD IC name. Choose one of the following:
 *      - ST7262
 *      - ST7789
 *      - GC9503
 *      - GC9A01
 */
#define ESP_PANEL_LCD_NAME          ST7789

/* LCD resolution in pixels */
#define ESP_PANEL_LCD_H_RES         (320)
#define ESP_PANEL_LCD_V_RES         (240)

/* LCD Bus Settings */
/**
 * If set to 1, the bus will skip to initialize the corresponding host. Users need to initialize the host in advance.
 * It is useful if other devices use the same host. Please ensure that the host is initialized only once.
 */
#define ESP_PANEL_LCD_BUS_SKIP_INIT_HOST        (0)
/**
 * LCD bus type. Choose one of the following:
 *      - 0: I2C (not supported yet)
 *      - 1: SPI
 *      - 2: I80 (not supported yet)
 *      - 3: RGB
 */
#define ESP_PANEL_LCD_BUS_TYPE      (1)
/**
 * LCD bus parameters.
 *
 * Please refer to https://docs.espressif.com/projects/esp-idf/en/latest/esp32s3/api-reference/peripherals/lcd.html for details.
 */
#define ESP_PANEL_LCD_BUS_HOST_ID           (1)
...

/* LCD Color Settings */
/* LCD color depth in bits */
#define ESP_PANEL_LCD_COLOR_BITS    (16)
/*
 * LCD Color Space. Choose one of the following:
 *      - 0: RGB
 *      - 1: BGR
 */
#define ESP_PANEL_LCD_COLOR_SPACE   (0)
#define ESP_PANEL_LCD_INEVRT_COLOR  (0)

/* LCD Transformation Flags */
#define ESP_PANEL_LCD_SWAP_XY       (0)
#define ESP_PANEL_LCD_MIRROR_X      (0)
#define ESP_PANEL_LCD_MIRROR_Y      (0)

/* LCD Other Settings */
/* IO num of RESET pin, set to -1 if not use */
#define ESP_PANEL_LCD_IO_RST        (-1)
#define ESP_PANEL_LCD_RST_LEVEL     (0)

Here are some important macros for the LCD touch:

/* Set to 0 if not using LCD touch */
#define ESP_PANEL_USE_LCD_TOUCH     (0)

/**
 * LCD Touch IC name. Choose one of the following:
 *      - CST816S
 *      - FT5x06
 *      - GT1151
 *      - GT911
 *      - TT21100
 *      - STMPE610
 */
#define ESP_PANEL_LCD_TOUCH_NAME            TT21100

/* LCD Touch resolution in pixels */
#define ESP_PANEL_LCD_TOUCH_H_RES           (ESP_PANEL_LCD_H_RES)
#define ESP_PANEL_LCD_TOUCH_V_RES           (ESP_PANEL_LCD_V_RES)

/* LCD Touch Bus Settings */
/**
 * If set to 1, the bus will skip to initialize the corresponding host. Users need to initialize the host in advance.
 * It is useful if other devices use the same host. Please ensure that the host is initialized only once.
 */
#define ESP_PANEL_LCD_TOUCH_BUS_SKIP_INIT_HOST  (0)
/**
 * LCD touch bus type. Choose one of the following:
 *      - 0: I2C
 *      - 1: SPI
 */
#define ESP_PANEL_LCD_TOUCH_BUS_TYPE            (0)
/**
 * LCD touch bus parameters.
 *
 * Please refer to https://docs.espressif.com/projects/esp-idf/en/latest/esp32s3/api-reference/peripherals/lcd.html for details.
 */
#define ESP_PANEL_LCD_TOUCH_BUS_HOST_ID     (0)
...

/* LCD Touch Transformation Flags */
#define ESP_PANEL_LCD_TOUCH_SWAP_XY         (0)
#define ESP_PANEL_LCD_TOUCH_MIRROR_X        (0)
#define ESP_PANEL_LCD_TOUCH_MIRROR_Y        (0)

/* LCD Touch Other Settings */
#define ESP_PANEL_LCD_TOUCH_IO_RST          (-1)
#define ESP_PANEL_LCD_TOUCH_IO_INT          (-1)
#define ESP_PANEL_LCD_TOUCH_RST_LEVEL       (0)
#define ESP_PANEL_LCD_TOUCH_INT_LEVEL       (0)

Here are some important macros for the backlight:

#define ESP_PANEL_USE_BL                    (0)

/* IO num of backlight pin */
#define ESP_PANEL_LCD_IO_BL                 (45)

/* If the backlight is on when high level, set to 1; otherwise to 0 */
#define ESP_PANEL_LCD_BL_ON_LEVEL           (1)

/* Set to 1 if use PWM for backlight brightness control. */
#define ESP_PANEL_LCD_BL_USE_PWM            (0)

/**
 *  Backlight LEDC Parameters.
 *
 *  Please refer to https://docs.espressif.com/projects/esp-idf/en/latest/esp32s3/api-reference/peripherals/ledc.html for details.
 */
#define ESP_PANEL_LCD_BL_PWM_TIMER          (0)
...

Use Library

Use the library in the sketch, and the following codes show the usage of common APIs:

#include <ESP_Panel_Library.h>

// Create an ESP_Panel object
ESP_Panel *panel = new ESP_Panel();

// Initialize and start the ESP_Panel object
panel->init();
panel->begin();

// Get the LCD object and operate it
panel->getLcd()->setCallback(callback, NULL);
panel->getLcd()->drawBitmap(0, 0, width, height, color);

// Get the LCD touch object and operate it
panel->getLcdTouch()->readData();
bool touched = panel->getLcdTouch()->getTouchState();
if(touched) {
    TouchPoint point = panel->getLcdTouch()->getPoint();
    Serial.printf("Touch point: x %d, y %d\n", point.x, point.y);
}

// Get the backlight object and operate it
panel->getBacklight()->on();
panel->getBacklight()->off();
panel->getBacklight()->setBrightness(50);

// Release the ESP_Panel object
delete panel;

Supported Boards

Name	LCD Bus	LCD Controller	Touch Bus	Touch Controller
ESP32-C3-LCDkit	SPI	GC9A01	-	-
ESP32-S3-Box	SPI	ILI9342	I2C	TT21100
ESP32-S3-Box-Lite	SPI	ST7789	-	-
ESP32-S3-EYE	SPI	ST7789	-	-
ESP32-S3-LCD-EV-Board	3-wire SPI + RGB	GC9503	I2C	FT5X06
ESP32-S3-LCD-EV-Board-2	RGB	ST7262E43	I2C	GT1151
ESP32-S3-USB-OTG	SPI	ST7789	-	-

Supported Drivers

Bus

Bus	Version
I2C	-
SPI	-
3-wire SPI + RGB	v1.0.0

LCD Controller

LCD Controller	Version
ST7262	-
ST7789	-
GC9503	1.0.0
GC9A01	1.0.1

Touch Controller

Touch Controller	Version
esp_lcd_touch	1.0.4
CST816S	1.0.3
FT5x06	1.0.5~1
GT1151	1.0.5~1
GT911	1.0.7~1
TT21100	1.0.7~1
STMPE610	1.0.6

License

Lzw655/ESP32_Display_Panel

ErrorLooks like something went wrong!

About

Resources

License

Uh oh!

Stars

Watchers

Forks

Releases 3

Packages 0

Uh oh!

Languages

Error
Looks like something went wrong!

Packages