The hantro_variant.init() function is there for platforms
to perform hardware-specific initialization, such as
clock rate bumping.

Not all platforms require it, so make it optional.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>

When the VP8 decoders can't find a reference frame,
the driver falls back to the current output frame.

This will probably produce some undesirable results,
leading to frame corruption, but shouldn't cause
noisy warnings.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>

The OV10635 image sensor embedded in the camera module is currently
reset after the MAX9271 initialization with two long delays that were
most probably not correctly characterized.

Re-work the image sensor reset procedure by holding the chip in reset
during the MAX9271 configuration, removing the long sleep delays and
only wait after the chip exits from reset for 350-500 microseconds
interval, which is larger than the minimum (2048 * (1 / XVCLK)) timeout
characterized in the chip manual.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

The camera module initialization routine does not check the return
value of a few functions. Fix that.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

When the device is identified the driver currently reports the
names of the chips embedded in the camera module.

Report the name of the camera module itself instead.
Cosmetic change only.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Enable the noise immunity threshold at the end of the rdacm20
initialization routine.

The rdacm20 camera module has been so far tested with a startup
delay that allowed the embedded MCU to program the serializer. If
the initialization routine is run before the MCU programs the
serializer and the image sensor and their addresses gets changed
by the rdacm20 driver it is required to manually enable the noise
immunity threshold to make the communication on the control channel
more reliable.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

There's no reason to allocate dynamically the 'serializer' field in
the driver structure.

Embed the field and adjust all its users in the driver.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

The current RDACM21 initialization routine powers up the OV10640 image
sensor after the OV490 ISP. The ISP is programmed with a firmware loaded
from an embedded serial flash that (most probably) tries to interact and
program also the image sensor connected to the ISP.

As described in commit "media: i2c: rdacm21: Fix OV10640 powerup" the
image sensor powerdown signal is kept high by an internal pull up
resistor and occasionally fails to startup correctly if the powerdown
line is not asserted explicitly. Failures in the OV10640 startup causes
the OV490 firmware to fail to boot correctly resulting in the camera
module initialization to fail consequentially.

Fix this by powering up the OV10640 image sensor before testing the
OV490 firmware boot completion, by splitting the ov10640_initialize()
function in an ov10640_power_up() one and an ov10640_check_id() one.

Also make sure the OV10640 identification procedure gives enough time to
the image sensor to resume after the programming phase performed by the
OV490 firmware by repeating the ID read procedure.

This commit fixes a sporadic start-up error triggered by a failure to
detect the OV490 firmware boot completion:
rdacm21 8-0054: Timeout waiting for firmware boot

[hverkuil: fixed two typos in commit log]

Fixes: a59f853 ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

The OV10640 image sensor powerdown signal is controlled by the first
line of the OV490 GPIO pad #1, but the pad #0 identifier
OV490_GPIO_OUTPUT_VALUE0 was erroneously used. As a result the image
sensor powerdown signal was never asserted but was left floating and
kept high by an internal pull-up resistor, causing sporadic failures
during the image sensor startup phase.

Fix this by using the correct GPIO pad identifier and wait the mandatory
1.5 millisecond delay after the powerup lane is asserted. The reset
delay is not characterized in the chip manual if not as "255 XVCLK +
initialization". Wait for at least 3 milliseconds to guarantee the SCCB
bus is available.

While at it also fix the reset sequence, as the reset line was released
before the powerdown one, and the line was not cycled.

This commit fixes a sporadic start-up error triggered by a failure to
read the OV10640 chip ID:
rdacm21 8-0054: OV10640 ID mismatch: (0x01)

Fixes: a59f853 ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Add a delay after the OV490 chip is put in reset state. The reset
signal shall be held low for at least 250 useconds.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

The MAX9271 chip manual prescribes a delay of 5 milliseconds
after the chip exits from low power state.

Add a new function to the max9271 library driver that wakes up the chip
with a dummy i2c transaction and implements the correct delay of 5
milliseconds after the chip exits from low power state.

Use the newly introduced function in the rdacm20 and rdacm21 camera
drivers. The former was not respecting the required delay while the
latter was waiting for a too-short timeout.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Check the return value of the max9271_write() function in the
max9271 library driver.

While at it, modify an existing condition to be made identical
to other checks.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Rephrase a comment in .bound() callback to make it clear we register
a subdev notifier and remove a redundant comment about disabling i2c
auto-ack.

No functional changes intended.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Provide a macro to define the reverse channel amplitude to
be used to compensate the remote serializer noise immunity.

While at it, update a comment.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Cache the current channel amplitude in a driver variable
to skip updating it if the newly requested value is the same
as the currently configured one.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Rename the reverse_channel_mv variable to init_rev_chan_mv as
the next patch will cache the reverse channel amplitude in
a new driver variable.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

The parameters to max9286_i2c_mux_configure() fits on the previous
line. Adjust it.

Cosmetic change only.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

RK3036's VPU IP block is the same as RK3288 has, except that it doesn't
have an encoder, decoding is supported up to 1920x1088 only and the axi
clock can be set to 300 MHz max.

Add a new RK3036 variant which reflects these differences.

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

RK3066's VPU IP block is the predecessor from what RK3288 has.
The hardware differences are:
  - supports decoding frame sizes up to 1920x1088 only
  - doesn't have the 'G1_REG_SOFT_RESET' register
    (requires another .reset callback for hantro_codec_ops,
     since writing this register will result in non-working
     IP block)
  - has one ACLK/HCLK per vdpu/vepu
  - ACLKs can be clocked up to 300 MHz only
  - no MMU
    (no changes required: CMA will be transparently used)

Add a new RK3066 variant which reflect this differences. This variant
can be used for RK3188 as well.

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Merge the two Rockchip platform drivers into one as it was suggested at
[1] and [2].
This will hopefully make it easier to add new variants (which are surely
to come for Rockchip).
Also rename from "rk3288" to "v(d/e)pu1" and "rk3399" to "v(d/e)pu2"
where applicable, as this is the dicition the vendor uses and will
also refelect the variants that get added later in this series. Rename
from "rk3288" to "rockchip" if applicable to both hardware versions.

[1] https://patchwork.kernel.org/project/linux-rockchip/patch/20210107134101.195426-6-paul.kocialkowski@bootlin.com/
[2] https://patchwork.kernel.org/project/linux-rockchip/patch/20210525152225.154302-5-knaerzche@gmail.com/

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Reorder variants in hantro driver alphanumeric.

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Document the RK3228 compatible for rockchip-vdec.
Also add the optional assigned-clocks and assigned-clock-rates
properties.

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Add compatibles for RK3036, RK3066, RK3188 and RK3228. Also reflect the
changes to the additional clocks for RK3066/RK3188.

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Fix the following kerneldoc warnings:

drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'AP_IPIMSG_ENC_INIT' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'AP_IPIMSG_ENC_SET_PARAM' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'AP_IPIMSG_ENC_ENCODE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'AP_IPIMSG_ENC_DEINIT' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'VPU_IPIMSG_ENC_INIT_DONE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'VPU_IPIMSG_ENC_SET_PARAM_DONE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'VPU_IPIMSG_ENC_ENCODE_DONE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'VPU_IPIMSG_ENC_DEINIT_DONE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Excess enum value 'VPU_IPIMSG_ENC_XXX_DONE' description in 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Excess enum value 'AP_IPIMSG_ENC_XXX' description in 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:120: warning: Enum value 'VENC_IPI_MSG_STATUS_OK' not described in enum 'venc_ipi_msg_status'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:120: warning: Enum value 'VENC_IPI_MSG_STATUS_FAIL' not described in enum 'venc_ipi_msg_status'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_SYS' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_MISC' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_LD' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_TOP' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_CM' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_AD' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_AV' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_PP' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_HWD' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_HWQ' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_HWB' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_HWG' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'NUM_MAX_VDEC_REG_BASE' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VENC_SYS' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VENC_LT_SYS' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'NUM_MAX_VCODEC_REG_BASE' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:58: warning: Enum value 'MTK_INST_DECODER' not described in enum 'mtk_instance_type'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:58: warning: Enum value 'MTK_INST_ENCODER' not described in enum 'mtk_instance_type'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_NONE' not described in enum 'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_BITRATE' not described in enum 'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_FRAMERATE' not described in enum 'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_INTRA_PERIOD' not described in enum
'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_FORCE_INTRA' not described in enum
'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_GOP_SIZE' not described in enum 'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:103: warning: Function parameter or member 'fourcc' not described in 'mtk_video_fmt'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:103: warning: Function parameter or member 'type' not described in 'mtk_video_fmt'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:103: warning: Function parameter or member 'num_planes' not described in 'mtk_video_fmt'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:103: warning: Function parameter or member 'flags' not described in 'mtk_video_fmt'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:112: warning: Function parameter or member 'fourcc' not described in 'mtk_codec_framesizes'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:112: warning: Function parameter or member 'stepwise' not described in 'mtk_codec_framesizes'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:120: warning: Enum value 'MTK_Q_DATA_SRC' not described in enum 'mtk_q_type'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:120: warning: Enum value 'MTK_Q_DATA_DST' not described in enum 'mtk_q_type'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'visible_width' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'visible_height' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'coded_width' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'coded_height' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'field' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'bytesperline' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'sizeimage' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'fmt' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:177: warning: Function parameter or member 'clk_name' not described in 'mtk_vcodec_clk_info'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:177: warning: Function parameter or member 'vcodec_clk' not described in
'mtk_vcodec_clk_info'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:185: warning: Function parameter or member 'clk_info' not described in 'mtk_vcodec_clk'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:185: warning: Function parameter or member 'clk_num' not described in 'mtk_vcodec_clk'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'vdec_clk' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'larbvdec' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'venc_clk' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'larbvenc' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'dev' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'mtkdev' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:300: warning: Function parameter or member 'decoded_frame_cnt' not described in
'mtk_vcodec_ctx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:332: warning: Function parameter or member 'min_bitrate' not described in
'mtk_vcodec_enc_pdata'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:405: warning: Function parameter or member 'venc_pdata' not described in 'mtk_vcodec_dev'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:405: warning: Function parameter or member 'decode_workqueue' not described in
'mtk_vcodec_dev'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_INIT' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_START' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_END' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_DEINIT' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_RESET' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_INIT_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_START_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_END_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_DEINIT_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_RESET_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Excess enum value 'AP_IPIMSG_XXX' description in 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Excess enum value 'VPU_IPIMSG_XXX_ACK' description in 'vdec_ipi_msgid'

In some cases I just changed /** to /*, in other cases the missing
field descriptions were added.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

No need to use & to get the start address of an array.

Fix the size of vga_edid.edid to a single block (128 bytes) to fix
this smatch error:

adv7842.c:2538 adv7842_set_edid() error: memcpy() '&state->vga_edid.edid' too small (128 vs 512)

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

Only 2 functions allocate some memory. They are both in cx88-core.c

When memory is allocated in 'cx88_risc_buffer()', GFP_KERNEL can be
used because its 2 callers end up to '.buf_prepare' functions in 'vb2_ops'
structures.
The call chains are:

  .buf_prepare                   (cx88-vbi.c)
    --> buffer_prepare           (cx88-vbi.c)
      --> cx88_risc_buffer

  .buf_prepare                   (cx88-video.c)
    --> buffer_prepare           (cx88-video.c)
      --> cx88_risc_buffer

When memory is allocated in 'cx88_risc_databuffer()', GFP_KERNEL can be
used because its 2 callers end up to 'snd_cx88_hw_params' which already
uses GFP_KERNEL and '.buf_prepare' functions in 'vb2_ops' structures.
The call chains are:

  snd_cx88_hw_params                   (cx88-alsa.c)
    --> cx88_risc_databuffer

  .buf_prepare                         (cx88-blackbird.c)
    --> buffer_prepare                 (cx88-blackbird.c)
      --> cx8802_buf_prepare           (cx88-mpeg.c)
        --> cx88_risc_databuffer

  .buf_prepare                         (cx88-dvb.c)
    --> buffer_prepare                 (cx88-dvb.c)
      --> cx8802_buf_prepare           (cx88-mpeg.c)
        --> cx88_risc_databuffer

@@ @@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@ @@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@ @@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@ @@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

It is only read-from, so make it const. In order to be able to do this,
constify all places where mxc_jpeg_fmt is used, in function arguments,
return values and pointers. On top of that, make the name a pointer to
const char.

On aarch64, this shrinks object code size with 550 bytes with gcc 11.1.0,
and almost 2kB with clang 12.0.0.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

The only usage of mxc_jpeg_m2m_ops is to pass its address to
v4l2_m2m_init() which takes a pointer to const struct v4l2_m2m_ops. Make
it const to allow the compiler to put it in read-only memory.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Add support for two new media bus formats, Y10 and Y8.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Prefer 'unsigned int' to bare use of 'unsigned'.
So modified variable type 'unsigned' to 'unsigned int' in v4l2-event.c.

Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Fixed all the Coding style issues generated by checkpatch.pl.
The changes made considering the --strict option.

Signed-off-by: Piyush Thange <pthange19@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

The m2m_ctx resources was allocated by v4l2_m2m_ctx_init() in g2d_open()
should be freed from g2d_release() when it's not used.

Fix it

Fixes: 9188473 ("[media] v4l: add G2D driver for s5p device family")
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

When i2c_new_client_device() fails, cafe_pci_probe() cleans up all
resources and returns 0. The patch sets the error code on the
corresponding path.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Some BT.656 sensors (e.g. ADV718x) transmit frames with unstable BT.656
sync codes after initial power on. This confuses the imx CSI,resulting
in vertical and/or horizontal sync issues. Skip the first 20 frames
to avoid the unstable sync codes.

[fabio: fixed checkpatch warning and increased the frame skipping to 20]

Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Those blobs can only be read. So, don't confuse users with 'writable'
flags.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>