From 2017-08, ndproxy is made available from the official FreeBSD ports tree: ndproxy port at FreeBSD
This way, you can get precompiled packages for many hardware targets, or install it from the sources, while maintaining dependencies. The port is based on this GitHub source repository content.
Kernel module for FreeBSD that implements IPv6 Neighbor Discovery proxying over Ethernet-like access networks
With this module, your uplink provider continues to see you as a flat network, but you can subnet your IPv6 prefix and route packets to your preferred gateway (a Cisco router for instance), that may split your network into several subnets. To achieve this goal, your FreeBSD router will redirect packets coming from your uplink provider router to your gateway. You simply need to connect one of your FreeBSD host interfaces to the layer 2 that interconnects your provider and your gateway, and disable MLD snooping on the interconnection switch.
Tested with success on FreeBSD 10.x, FreeBSD 11.x, FreeBSD 12.x and CURRENT (FreeBSD 13)
NDPROXY(4) FreeBSD Kernel Interfaces Manual NDPROXY(4)
NAME
ndproxy -- Neighbor Discovery Proxy
SYNOPSIS
ndproxy is a kernel module that implements IPv6 Neighbor Discovery proxy-
ing over Ethernet-like access networks, with many options to handle sev-
eral use-cases.
ndproxy replies to a neighbor solicitation with a specific neighbor ad-
vertisement, in order to let the PE uplink router send further packets to
a CPE downlink router, that may or may not be the same node that run nd-
proxy.
The hook-based pfil(9) framework is used to let ndproxy be invoked for
every IPv6 incoming packet, in order to specifically handle and filter
neighbor solicitations and reply with appropriate neighbor advertise-
ments.
ND (Neighbor Discovery) packets are mainly targeted at solicited-node
multicast addresses, but ndproxy has no information about the hosts to
proxy, then it can not join the corresponding groups. Thus, the interface
on which ndproxy listen to solicitations must be put into permanently
promiscuous mode: add "promisc" to the ifconfig_<interface> variable in
rc.conf(5).
For the same reason, MLD snooping must be disabled on the switches that
share the PE/CPE interconnect (the layer-2 link the listening interface
is attached to). Note that MLD snooping must not be disabled entirely on
each switch, but only on the corresponding vlan.
The interface on which ndproxy listen to solicitations only need to be
assigned a link-local address. No information about the delegated prefix
and no global address are needed on this interface. It is sufficient to
add "inet6 -ifdisabled -accept_rtadv auto_linklocal" to the ifconfig_<in-
terface>_ipv6 variable in rc.conf(5).
DIFFERENCES WITH NDP
The target address to proxy must be given when using the ndp(8) command-
line tool with the proxy option. On the contrary, ndproxy does not rely
on a list of target addresses to proxy. Thus, RFC-4941 temporary ad-
dresses can be proxyfied. For security reasons, many operating systems
use a temporary address when establishing outbound connections.
When using ndp(8) command-line tool with the proxy option, the proxyfied
packets are redirected to the node that run ndp. With ndproxy, the host
that run ndp can be used only to redirect packets to another IPv6 inter-
nal router, for instance a dedicated router with hardware support of IPv6
routing process.
PREFIX SUBNETTING
Connecting a flat IPv6 network to the Internet is easily done with the
RFC-4861 ND protocol. But connecting a subnetted IPv6 prefix is more com-
plicated, depending on the ISP network design choices. ndproxy can help
subscribers to achieve this goal.
Here are some protocols or mechanisms the ISP need to support, when the
delegated prefix must be subnetted and assigned to multiple links within
the subscriber's network. For instance, the ISP could learn routes from
the subscriber router using an IGP routing protocol, but the ISP and the
subscriber must agree with a common routing protocol. The ISP could also
feed the PE with a static route to the CPE router, but the ISP must be
informed about the subscriber router address. Finally, the ISP could use
the RFC-3633 IPv6 Prefix Options with DHCPv6 to delegate the prefix from
its PE router to a requesting subscriber's router: in such a case, the
ISP must support the DHCPv6 option.
ndproxy has been written for subscribers to ISP that do not support any
of those mechanisms or protocols, thus not being able to natively subnet
their IPv6 delegated prefix.
NETWORK DESIGN
Here is a generic network design using ndproxy to solve such situations:
______________________ \
/ \ \
| ISP core network | \
\__________ ___________/ |
| | ISP network
| dsl to subscriber premises |
| /
+---+---------------------+ /
| PE or triple-play box | /
+-----------+-------------+
|
PE/CPE interconnect | /48 prefix \
--+---------+---------+-- \
| no mld snooping | \
| | |
+----+--------+ +----+-----+ |
| CPE | | ndproxy | |
| IPv6 router | | BSD host | |
+----+---+----+ +----------+ |
subnet1 | | subnet2 | Subscriber
----+-----+- -+-----+------ | network
| /60 | /60 |
+---+------+ +----+-----+ |
|Subscriber| |Subscriber| /
| host | | host | /
+----------+ +----------+ /
Note that many other use-cases can be handled with ndproxy: the BSD host
and the CPE router can be the same node, the delegated-prefix length can
be /64, the PE router can have several interfaces on the ISP/Subscriber
layer-2 boundary, there can be multiple PE routers, etc.
PREFIX LENGTH
Even if the IESG and the IAB first recommended the allocations of /48
prefixes in the general case, for the boundary between the public and the
private topology (see RFC-3177), and that some Regional Internet Reg-
istries (APNIC, ARIN and RIPE) have subsequently revised the end site as-
signment policy to encourage the assignment of /56 blocks to end sites,
and that RFC-6177 finally recommended giving home sites significantly
more than a single /64, in order for home sites to be given multiple sub-
nets, some ISP currently only delegate /64 prefixes.
In such a case, the subscriber should subnet a RFC-4193 Unique Local IPv6
Unicast Addresses prefix to the internal subnetworks, for internal-to-in-
ternal communications. The /64 global prefix should be routed to the only
internal subnet in which RFC-4941 temporary addresses are used by hosts
when establishing outbound connections. Static routes on the CPE router
should be set to let hosts on other internal subnets be able to communi-
cate with the Internet. Using temporary addresses for outbound connec-
tions to the Internet must be disabled on hosts on those other internal
subnets.
IPv6 EXTENSION HEADERS
For security reasons, ndproxy explicitely rejects neighbor solicitation
packets containing any extension header. Such a packet is mainly unat-
tended:
Fragmentation:
According to RFC-6980, IPv6 fragmentation header is forbid-
den in all neighbor discovery messages.
Hop-by-hop header:
commonly used for jumbograms or for MLD. Should not involve
neighbor solicitation packets.
Destination mobility headers:
commonly used for mobility, ndproxy does not support these
headers.
Routing header:
commonly used for mobility or source routing, ndproxy does
not support these headers.
AH & ESP headers:
securing the neighbor discovery process is not done with
IPsec but with the SEcure Neighbor Discovery protocol
(RFC-3971). ndproxy can not support RFC-3971, since proxi-
fying ND packets is some kind of a spoofing process.
EXCEPTION ADDRESSES
Some neigbhor solicitations sent on the PE/CPE interconnect must not be
proxyfied:
1. solicitations sent by other nodes than the PE;
2. solicitations sent by the PE to reach any on-link address (the ad-
dress filled in the target address option) owned by nodes attached
to the PE/CPE interconnect, for instance to reach the CPE, the nd-
proxy host or other hosts attached to this layer-2 interconnect.
The target addresses filled in those solicitations that ndproxy must ig-
nore have to be declared via sysctl (net.inet6.ndproxyconf_excep-
tion_ipv6_addresses). This list must contain the link-local and global-
scoped unicast and anycast addresses of the CPE, of the ndproxy host and
of any other host than the PE attached to the PE/CPE interconnect.
Failing to maintain this list correctly could lead to badly redirect some
packets to the CPE, but with a simple network design, this list can be
let empty.
UPLINK ROUTER ADDRESSES
ndproxy only handles packets originating from one of the PE addresses.
During its address resolution process, different source addresses can be
choosen by the PE, depending on the packet that triggered the process or
depending on other external constraints.
Here are some cases when it can occur:
1. The PE may have multiple interfaces;
2. There may be multiple PE;
3. Many routers choose to use a link-local address when sending neigh-
bor solicitations, but when an administrator of such a router, also
having a global address assigned on the same link, tries to send
packets (echo request, for instance) to an on-link destination
global address, the source address of the echo request packet
prompting the solicitation may be global-scoped according to the se-
lection algorithm described in RFC-6724. Therefore, the source ad-
dress of the Neighbor Solicitation packet should also be selected in
the same global scope, according to RFC-4861;
4. When the uplink router does not yet know its own address, it must
use the unspecified address, according to RFC-4861.
So, it can not be assumed that an uplink router will always use the same
IPv6 address to send neighbor solicitations. Each assigned address that
can be used as a source address by the PE on its downlink interface must
then be declared to ndproxy via sysctl (net.inet6.ndproxyconf_up-
link_ipv6_addresses).
ndproxy will only handle packets that come from one of these addresses.
A special care must be taken about the unsolicited address. It may be
used by the PE, then it is part of the list of PE addresses and should
therefore be added to the list of PE addresses. Since this address can
also be used by other nodes during some initialization steps (for in-
stance when hot-swapping an Ethernet board), another node could use this
address to send neighbor solicitations that ndproxy should not handle,
because they are not sent by the PE. In fact, this is not a problem be-
cause the target address option contained in a solicitation from this
other node should be in the exception list. So, adding the unsolicited
address in the PE addresses list should be safe.
Failing to maintain this list correctly could lead the PE not to be able
to establish outbound connections to nodes on the PE/CPE interconnect,
but if this list contains at least the PE link-local address, IPv6 con-
nectivity should be correctly established between the Internet and the
internal subscriber's subnets.
CONFIGURATION
An IPv6 address can be any valid textual representation according to
RFC-4291 and RFC-5952 (this means that transitional textual representa-
tion is fully supported). Other representations will trigger an error
event. IPv6 address lists must be formated as series of IPv6 adresses
separated by semi-colons.
The sysctl utility or rc.conf(5) are used to set ndproxy configuration
parameters.
If you have installed ndproxy as a port or as a package, set the follow-
ing variables in rc.conf(5) and load the module at boot time by placing
the following line in rc.conf(5):
ndproxy_enable="YES"
On the contrary, if you have NOT installed ndproxy as a port or as a
package but as a standalone distribution, place the sysctl entries in
sysctl.conf(5) and load the module at boot time by placing the following
line in loader.conf(5):
ndproxy_load="YES"
net.inet6.ndproxyconf_uplink_interface sysctl entry or
ndproxy_uplink_interface rc.conf variable:
Name of the interface talking to the broadcast multi-access
network connecting the PE and CPE routers.
Example: "vlan2".
net.inet6.ndproxyconf_downlink_mac_address sysctl entry or
ndproxy_downlink_mac_address rc.conf variable:
MAC address of the CPE router. Neighbor advertisements sent
by ndproxy will be filled with this address in the target
link-layer address option. The format of this parameter is
the hexadecimal representation made of 6 groups of 2 hexa-
decimal numbers separated by colons.
Example: "00:0C:29:B6:43:D5".
net.inet6.ndproxyconf_exception_ipv6_addresses sysctl entry or
ndproxy_exception_ipv6_addresses rc.conf variable:
Target addresses not to proxy. In a simple network design,
this list can be let empty. See section "EXCEPTION AD-
DRESSES".
Example:
"fe80::20d:edff:fe7b:68b7;fe80::222:15ff:fe3b:59a".
net.inet6.ndproxyconf_uplink_ipv6_addresses sysctl entry or
ndproxy_uplink_ipv6_addresses rc.conf variable:
Addresses of the PE. This list should at least contain the
PE link-local address. See section "UPLINK ROUTER AD-
DRESSES".
Example:
"fe80::207:cbff:fe4b:2d20;2a01:e35:8aae:bc60::1;::".
net.inet6.ndproxycount sysctl entry:
Number of advertisements sent.
SEE ALSO
inet6(4), rc.conf(5), loader.conf(5), sysctl.conf(5), sysctl(8),
loader(8), pfil(9)
AUTHOR
Alexandre Fenyo <alex@fenyo.net> - www.fenyo.net
FreeBSD 13.0 May 27, 2017 FreeBSD 13.0