From 38bdaa1f4c8028c2cf9dd0b026441e193eef15d4 Mon Sep 17 00:00:00 2001 From: Justin Bunton Date: Fri, 25 Oct 2024 03:31:25 +0000 Subject: [PATCH 1/3] Updated 2 files via CloudCannon. --- .../msr2/troubleshooting/msr2-code.md | 63 ++++++++----------- 1 file changed, 26 insertions(+), 37 deletions(-) diff --git a/docs/products/msr2/troubleshooting/msr2-code.md b/docs/products/msr2/troubleshooting/msr2-code.md index a29c31232..05dd849b6 100644 --- a/docs/products/msr2/troubleshooting/msr2-code.md +++ b/docs/products/msr2/troubleshooting/msr2-code.md @@ -1,39 +1,28 @@ # Manually Uploading Code Through ESPHome -If your device becomes unresponsive and you've exhausted the other troubleshooting methods you can upload a fresh set of firmware by following the below guide. The utility does need to be run from Chrome or Edge. - - - -If your device has already been connected to Home Assistant previously please refer to Removing Device From Home Assistant first before proceeding - - -1. Plug your MSR-2 into your computer with a quality USBC cable that supports data transfer -2. Navigate to our installer page and click connect ** Install Page ** - -3. Select your Apollo device, it will show with a similar name to the one below, and click connect. If you aren't sure which device it is, you can unplug the MSR-2 and see which disappears. - -![ComSelection.png](../assets/comselection.png) - -If no device shows, click cancel and then install the recommended driver that shows on the popup. If you have installed the driver, tried different cables, and it still won't work refer here for putting the MSR-2 in bootloader mode and then retry step 3. Putting MSR-2 In Boot Mode Document - - -4. Choose to install the new firmware - -![](../assets/image-1698806750134.png) - -6. Wait for the installer to finish - - ![](../assets/image-1698806082666.png) - - -7. After finishing, check for the Apollo hotspot and connect. This might not show if you previously had the MSR-2 connected to your wifi - -8. Log into Home Assistant and go to the ESPHome addon check to see if you can adopt the device. - - - - -If you encounter the below error, please complete the Putting MSR-2 In Boot Mode Document and go back to step 3. - - - ![](../assets/image-1698806793309.png) \ No newline at end of file +If your device becomes unresponsive and you've exhausted the other troubleshooting methods you can upload a fresh set of firmware by following the below guide. The utility does need to be run from Chrome or Edge. + +If your device has already been connected to Home Assistant previously please refer to Removing Device From Home Assistant first before proceeding + +1. Plug your MSR-2 into your computer with a quality USBC cable that supports data transfer +2. Navigate to our installer page and click connect [\*\* Install Page \*\*](https://apolloautomation.github.io/MSR-2/) +3. Select your Apollo device, it will show with a similar name to the one below, and click connect. If you aren't sure which device it is, you can unplug the MSR-2 and see which disappears. + +![ComSelection.png](../assets/comselection.png) + +If no device shows, click cancel and then install the recommended driver that shows on the popup. If you have installed the driver, tried different cables, and it still won't work refer [here](https://apolloautomation.github.io/docs/products/msr2/troubleshooting/msr2-boot-mode/)for putting the MSR-2 in bootloader mode and then retry step 3. + +4. Choose to install the new firmware + +![](../assets/image-1698806750134.png) + +6. Wait for the installer to finish + +![](../assets/image-1698806082666.png) + +7. After finishing, check for the Apollo hotspot and connect. This might not show if you previously had the MSR-2 connected to your wifi +8. Log into Home Assistant and go to the ESPHome addon check to see if you can adopt the device. + +If you encounter the below error, please complete the [Putting MSR-2 In Boot Mode Document](https://apolloautomation.github.io/docs/products/msr2/troubleshooting/msr2-boot-mode/) and go back to step 3. + +![](../assets/image-1698806793309.png) \ No newline at end of file From c400aa96d328b5612934717e1b5cdc57a451aaf6 Mon Sep 17 00:00:00 2001 From: Justin Bunton Date: Fri, 25 Oct 2024 03:32:10 +0000 Subject: [PATCH 2/3] Updated 2 files via CloudCannon. --- docs/products/msr2/troubleshooting/msr2-boot-mode.md | 9 +++------ docs/products/msr2/troubleshooting/msr2-code.md | 2 -- 2 files changed, 3 insertions(+), 8 deletions(-) diff --git a/docs/products/msr2/troubleshooting/msr2-boot-mode.md b/docs/products/msr2/troubleshooting/msr2-boot-mode.md index 88d7f4716..cb1618f89 100644 --- a/docs/products/msr2/troubleshooting/msr2-boot-mode.md +++ b/docs/products/msr2/troubleshooting/msr2-boot-mode.md @@ -1,15 +1,12 @@ -# Putting The MSR-2 In Boot Mode +This will cover how to put the MSR-2 into boot mode. Sometimes, this is needed to upload new firmware if the device is struggling. -This will cover how to put the MSR-2 into boot mode. Sometimes, this is needed to upload new firmware if the device is struggling. - **Boot Button Only** 1. Please look at the photo below to help access the boot button through the top of the case 2. Use a pin to press and hold the boot button, while holding the boot button plug it into your computer/power and then release the boot button -![20240514_123742.jpg](../assets/MJ120240514-123742.jpg) - 4. Continue with [uploading the firmware document](https://wiki.apolloautomation.com/books/msr-2/page/manually-uploading-code-through-esphome) - +![20240514_123742.jpg](../assets/MJ120240514-123742.jpg)
4. Continue with [uploading the firmware document](https://wiki.apolloautomation.com/books/msr-2/page/manually-uploading-code-through-esphome) + **Boot and Reset Buttons** 1. Unplug the device diff --git a/docs/products/msr2/troubleshooting/msr2-code.md b/docs/products/msr2/troubleshooting/msr2-code.md index 05dd849b6..9fe0b74bb 100644 --- a/docs/products/msr2/troubleshooting/msr2-code.md +++ b/docs/products/msr2/troubleshooting/msr2-code.md @@ -1,5 +1,3 @@ -# Manually Uploading Code Through ESPHome - If your device becomes unresponsive and you've exhausted the other troubleshooting methods you can upload a fresh set of firmware by following the below guide. The utility does need to be run from Chrome or Edge. If your device has already been connected to Home Assistant previously please refer to Removing Device From Home Assistant first before proceeding From 4ebf74a6fd1fbd11c7c49047fd2c5423f7a9624c Mon Sep 17 00:00:00 2001 From: Justin Bunton Date: Fri, 25 Oct 2024 03:32:59 +0000 Subject: [PATCH 3/3] Updated 1 file via CloudCannon. --- docs/products/msr2/troubleshooting/msr2-boot-mode.md | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/docs/products/msr2/troubleshooting/msr2-boot-mode.md b/docs/products/msr2/troubleshooting/msr2-boot-mode.md index cb1618f89..9df29a733 100644 --- a/docs/products/msr2/troubleshooting/msr2-boot-mode.md +++ b/docs/products/msr2/troubleshooting/msr2-boot-mode.md @@ -5,7 +5,7 @@ This will cover how to put the MSR-2 into boot mode. Sometimes, this is needed t 1. Please look at the photo below to help access the boot button through the top of the case 2. Use a pin to press and hold the boot button, while holding the boot button plug it into your computer/power and then release the boot button -![20240514_123742.jpg](../assets/MJ120240514-123742.jpg)
4. Continue with [uploading the firmware document](https://wiki.apolloautomation.com/books/msr-2/page/manually-uploading-code-through-esphome) +![20240514_123742.jpg](../assets/MJ120240514-123742.jpg)
4. Continue with [uploading the firmware document](https://apolloautomation.github.io/docs/products/msr2/troubleshooting/msr2-code/) **Boot and Reset Buttons** @@ -14,6 +14,6 @@ This will cover how to put the MSR-2 into boot mode. Sometimes, this is needed t 3. Remove the device from the case 4. Plug it back into your computer 5. Press and hold the boot button, while holding it press and release the reset button, then release the boot button -6. Continue with [uploading the firmware document](https://wiki.apolloautomation.com/books/msr-2/page/manually-uploading-code-through-esphome) +6. Continue with [uploading the firmware document](https://apolloautomation.github.io/docs/products/msr2/troubleshooting/msr2-code/) ![20240514_120819.jpg](../assets/5T520240514-120819.jpg) \ No newline at end of file