{"payload":{"allShortcutsEnabled":false,"fileTree":{"ArduCopter":{"items":[{"name":".gitignore","path":"ArduCopter/.gitignore","contentType":"file"},{"name":"APM_Config.h","path":"ArduCopter/APM_Config.h","contentType":"file"},{"name":"APM_Config_mavlink_hil.h","path":"ArduCopter/APM_Config_mavlink_hil.h","contentType":"file"},{"name":"AP_State.pde","path":"ArduCopter/AP_State.pde","contentType":"file"},{"name":"ArduCopter.pde","path":"ArduCopter/ArduCopter.pde","contentType":"file"},{"name":"Attitude.pde","path":"ArduCopter/Attitude.pde","contentType":"file"},{"name":"GCS_Mavlink.pde","path":"ArduCopter/GCS_Mavlink.pde","contentType":"file"},{"name":"Log.pde","path":"ArduCopter/Log.pde","contentType":"file"},{"name":"Makefile","path":"ArduCopter/Makefile","contentType":"file"},{"name":"Parameters.h","path":"ArduCopter/Parameters.h","contentType":"file"},{"name":"Parameters.pde","path":"ArduCopter/Parameters.pde","contentType":"file"},{"name":"ReleaseNotes.txt","path":"ArduCopter/ReleaseNotes.txt","contentType":"file"},{"name":"UserCode.pde","path":"ArduCopter/UserCode.pde","contentType":"file"},{"name":"UserVariables.h","path":"ArduCopter/UserVariables.h","contentType":"file"},{"name":"commands.pde","path":"ArduCopter/commands.pde","contentType":"file"},{"name":"commands_logic.pde","path":"ArduCopter/commands_logic.pde","contentType":"file"},{"name":"compassmot.pde","path":"ArduCopter/compassmot.pde","contentType":"file"},{"name":"compat.h","path":"ArduCopter/compat.h","contentType":"file"},{"name":"compat.pde","path":"ArduCopter/compat.pde","contentType":"file"},{"name":"config.h","path":"ArduCopter/config.h","contentType":"file"},{"name":"config_channels.h","path":"ArduCopter/config_channels.h","contentType":"file"},{"name":"control_acro.pde","path":"ArduCopter/control_acro.pde","contentType":"file"},{"name":"control_althold.pde","path":"ArduCopter/control_althold.pde","contentType":"file"},{"name":"control_auto.pde","path":"ArduCopter/control_auto.pde","contentType":"file"},{"name":"control_autotune.pde","path":"ArduCopter/control_autotune.pde","contentType":"file"},{"name":"control_circle.pde","path":"ArduCopter/control_circle.pde","contentType":"file"},{"name":"control_drift.pde","path":"ArduCopter/control_drift.pde","contentType":"file"},{"name":"control_flip.pde","path":"ArduCopter/control_flip.pde","contentType":"file"},{"name":"control_guided.pde","path":"ArduCopter/control_guided.pde","contentType":"file"},{"name":"control_land.pde","path":"ArduCopter/control_land.pde","contentType":"file"},{"name":"control_loiter.pde","path":"ArduCopter/control_loiter.pde","contentType":"file"},{"name":"control_ofloiter.pde","path":"ArduCopter/control_ofloiter.pde","contentType":"file"},{"name":"control_poshold.pde","path":"ArduCopter/control_poshold.pde","contentType":"file"},{"name":"control_rtl.pde","path":"ArduCopter/control_rtl.pde","contentType":"file"},{"name":"control_sport.pde","path":"ArduCopter/control_sport.pde","contentType":"file"},{"name":"control_stabilize.pde","path":"ArduCopter/control_stabilize.pde","contentType":"file"},{"name":"crash_check.pde","path":"ArduCopter/crash_check.pde","contentType":"file"},{"name":"defines.h","path":"ArduCopter/defines.h","contentType":"file"},{"name":"ekf_check.pde","path":"ArduCopter/ekf_check.pde","contentType":"file"},{"name":"events.pde","path":"ArduCopter/events.pde","contentType":"file"},{"name":"failsafe.pde","path":"ArduCopter/failsafe.pde","contentType":"file"},{"name":"fence.pde","path":"ArduCopter/fence.pde","contentType":"file"},{"name":"flight_mode.pde","path":"ArduCopter/flight_mode.pde","contentType":"file"},{"name":"heli.h","path":"ArduCopter/heli.h","contentType":"file"},{"name":"heli.pde","path":"ArduCopter/heli.pde","contentType":"file"},{"name":"heli_control_acro.pde","path":"ArduCopter/heli_control_acro.pde","contentType":"file"},{"name":"heli_control_stabilize.pde","path":"ArduCopter/heli_control_stabilize.pde","contentType":"file"},{"name":"inertia.pde","path":"ArduCopter/inertia.pde","contentType":"file"},{"name":"land_detector.pde","path":"ArduCopter/land_detector.pde","contentType":"file"},{"name":"leds.pde","path":"ArduCopter/leds.pde","contentType":"file"},{"name":"motor_test.pde","path":"ArduCopter/motor_test.pde","contentType":"file"},{"name":"motors.pde","path":"ArduCopter/motors.pde","contentType":"file"},{"name":"navigation.pde","path":"ArduCopter/navigation.pde","contentType":"file"},{"name":"nocore.inoflag","path":"ArduCopter/nocore.inoflag","contentType":"file"},{"name":"perf_info.pde","path":"ArduCopter/perf_info.pde","contentType":"file"},{"name":"position_vector.pde","path":"ArduCopter/position_vector.pde","contentType":"file"},{"name":"radio.pde","path":"ArduCopter/radio.pde","contentType":"file"},{"name":"readme.txt","path":"ArduCopter/readme.txt","contentType":"file"},{"name":"sensors.pde","path":"ArduCopter/sensors.pde","contentType":"file"},{"name":"setup.pde","path":"ArduCopter/setup.pde","contentType":"file"},{"name":"switches.pde","path":"ArduCopter/switches.pde","contentType":"file"},{"name":"system.pde","path":"ArduCopter/system.pde","contentType":"file"},{"name":"test.pde","path":"ArduCopter/test.pde","contentType":"file"}],"totalCount":63},"":{"items":[{"name":"APMrover2","path":"APMrover2","contentType":"directory"},{"name":"AntennaTracker","path":"AntennaTracker","contentType":"directory"},{"name":"ArduCopter","path":"ArduCopter","contentType":"directory"},{"name":"ArduPlane","path":"ArduPlane","contentType":"directory"},{"name":"FollowMe","path":"FollowMe","contentType":"directory"},{"name":"Tools","path":"Tools","contentType":"directory"},{"name":"docs","path":"docs","contentType":"directory"},{"name":"libraries","path":"libraries","contentType":"directory"},{"name":"mk","path":"mk","contentType":"directory"},{"name":".editorconfig","path":".editorconfig","contentType":"file"},{"name":".gitignore","path":".gitignore","contentType":"file"},{"name":".pydevproject","path":".pydevproject","contentType":"file"},{"name":".travis.yml","path":".travis.yml","contentType":"file"},{"name":"CONTRIBUTING.md","path":"CONTRIBUTING.md","contentType":"file"},{"name":"COPYING.txt","path":"COPYING.txt","contentType":"file"},{"name":"Doxyfile.in","path":"Doxyfile.in","contentType":"file"},{"name":"MAINTAINERS.md","path":"MAINTAINERS.md","contentType":"file"},{"name":"README.md","path":"README.md","contentType":"file"},{"name":"Vagrantfile","path":"Vagrantfile","contentType":"file"},{"name":"reformat.sh","path":"reformat.sh","contentType":"file"},{"name":"uncrustify_cpp.cfg","path":"uncrustify_cpp.cfg","contentType":"file"},{"name":"uncrustify_headers.cfg","path":"uncrustify_headers.cfg","contentType":"file"}],"totalCount":22}},"fileTreeProcessingTime":16.328206,"foldersToFetch":[],"repo":{"id":7512484,"defaultBranch":"master","name":"ardupilot","ownerLogin":"ArduPilot","currentUserCanPush":false,"isFork":false,"isEmpty":false,"createdAt":"2013-01-09T00:58:52.000Z","ownerAvatar":"https://avatars.githubusercontent.com/u/17919847?v=4","public":true,"private":false,"isOrgOwned":true},"symbolsExpanded":false,"treeExpanded":true,"refInfo":{"name":"ArduCopter-3.2.1","listCacheKey":"v0:1710377494.0","canEdit":false,"refType":"branch","currentOid":"03373d35c29d299356a3d80f262f335e8f100814"},"path":"ArduCopter/ReleaseNotes.txt","currentUser":null,"blob":{"rawLines":["ArduCopter Release Notes:","------------------------------------------------------------------","ArduCopter 3.2.1 11-Feb-2015 / 3.2.1-rc2 30-Jan-2015","Changes from 3.2.1-rc1","1) Bug Fixes:"," a) prevent infinite loop with linked jump commands"," b) Pixhawk memory corruption fix when connecting via USB"," c) vehicle stops at fence altitude limit in Loiter, AltHold, PosHold"," d) protect against multiple arming messages from GCS causing silent gyro calibration failure ","------------------------------------------------------------------","ArduCopter 3.2.1-rc1 08-Jan-2015","Changes from 3.2","1) Enhancements:"," a) reduced twitch when passing Spline waypoints"," b) Faster disarm after landing in Auto, Land, RTL"," c) Pixhawk LED turns green before arming only after GPS HDOP falls below 2.3 (only in flight modes requiring GPS)","2) Safety Features:"," a) Add desired descent rate check to reduce chance of false-positive on landing check"," b) improved MPU6k health monitoring and re-configuration in case of in-flight failure"," c) Rally point distance check reduced to 300m (reduces chance of RTL to far away forgotten Rally point)"," d) auto-disarm if vehicle is landed for 15seconds even in Auto, Guided, RTL, Circle"," e) fence breach while vehicle is landed causes vehicle to disarm (previously did RTL)","3) Bug Fixes:"," a) Check flight mode even when arming from GCS (previously it was possible to arm in RTL mode if arming was initiated from GCS)"," b) Send vehicle target destination in RTL, Guided (allows GCS to show where vehicle is flying to in these modes)"," c) PosHold wind compensation fix","------------------------------------------------------------------","ArduCopter 3.2 07-Nov2014 / 3.2-rc14 31-Oct-2014","Changes from 3.2-rc13","1) Safety Features:"," a) fail to arm if second gyro calibration fails (can be disabled with ARMING_CHECK)","2) Bug fixes:"," a) DCM-check to require one continuous second of bad heading before triggering LAND"," b) I2C bug that could lead to Pixhawk freezing up if I2C bus is noisy"," c) reset DCM and EKF gyro bias estimates after gyro calibration (DCM heading could drift after takeoff due to sudden change in gyro values)"," d) use primary GPS for LED status (instead of always using first GPS)","------------------------------------------------------------------","ArduCopter 3.2-rc13 23-Oct-2014","Changes from 3.2-rc12","1) DCM check triggers LAND if yaw disagrees with GPS by > 60deg (configure with DCM_CHECK_THRESH param) and in Loiter, PosHold, Auto, etc ","2) Safety features:"," a) landing detector checks baro climbrate between -1.5 ~ +1.5 m/s"," b) sanity check AHRS_RP_P and AHRS_YAW_P are never less than 0.05"," c) check set-mode requests from GCS are for this vehicle","3) Bug fixes:"," a) fix ch6 tuning of wp-speed (was getting stuck at zero)"," b) parachute servo set to off position on startup"," c) Auto Takeoff timing bug fix that could cause severe lean on takeoff"," d) timer fix for \"slow start\" of motors on Pixhawk (timer was incorrectly based on 100hz APM2 main loop speed)","4) reduced number of relays from 4 to 2 (saves memory and flash required on APM boards)","5) reduced number of range finders from 2 to 1 (saves memory and flash on APM boards)","6) allow logging from startup when LOG_BITMASK set to \"All+DisarmedLogging\" ","------------------------------------------------------------------","ArduCopter 3.2-rc12 10-Oct-2014","Changes from 3.2-rc11","1) disable sonar on APM1 and TradHeli (APM1 & APM2) to allow code to fit ","2) Add pre-arm and health check that gyro calibration succeeded ","3) Bug fix to EKF reporting invalid position and velocity when switched on in flight with Ch7/Ch8 switch ","------------------------------------------------------------------","ArduCopter 3.2-rc11 06-Oct-2014","Changes from 3.2-rc10","1) reduce lean on take-off in Auto by resetting horizontal position targets ","2) TradHeli landing check ignores overall throttle output","3) reduce AHRS bad messages by delaying 20sec after init to allow EKF to settle (Pixhawk only)","4) Bug fixes:"," a) fix THR_MIN scaling issue that could cause landing-detector to fail to detect landing when ch3 min~max > 1000 pwm"," b) fix Mediatek GPS configuration so update rate is set correctly to 5hz"," c) fix to Condition-Yaw mission command to support relative angles"," d) EKF bug fixes when recovering from GPS glitches (affects only Pixhawks using EKF)","------------------------------------------------------------------","ArduCopter 3.2-rc10 24-Sep-2014","Changes from 3.2-rc9","1) two-stage land-detector to reduce motor run-up when landing in Loiter, PosHold, RTL, Auto","2) Allow passthrough from input to output of channels 9 ~ 14 (thanks Emile!)","3) Add 4hz filter to vertical velocity error during AltHold","4) Safety Feature:"," a) increase Alt Disparity pre-arm check threshold to 2m (was 1m)"," b) reset battery failsafe after disarming/arming (thanks AndKe!)"," c) EKF only apply centrifugal corrections when GPS has at least 6 satellites (Pixhawk with EKF enabled only)","5) Bug fixes:"," a) to default compass devid to zero when no compass connected"," b) reduce motor run-up while landing in RTL","------------------------------------------------------------------","ArduCopter 3.2-rc9 11-Sep-2014","Changes from 3.2-rc8","1) FRAM bug fix that could stop Mission or Parameter changes from being saved (Pixhawk, VRBrain only)","------------------------------------------------------------------","ArduCopter 3.2-rc8 11-Sep-2014","Changes from 3.2-rc7","1) EKF reduced ripple to resolve copter motor pulsing","2) Default Param changes:"," a) AltHold Rate P reduced from 6 to 5"," b) AltHold Accel P reduced from 0.75 to 0.5, I from 1.5 to 1.0"," c) EKF check threshold increased from 0.6 to 0.8 to reduce false positives","3) sensor health flags sent to GCS only after initialisation to remove false alerts ","4) suppress bad terrain data alerts","5) Bug Fix:"," a)PX4 dataflash RAM useage reduced to 8k so it works again ","------------------------------------------------------------------","ArduCopter 3.2-rc7 04-Sep-2014","Changes from 3.2-rc6","1) Safety Items:"," a) Landing check made more strict (climb rate requirement reduced to 30cm/s, overall throttle < 25%, rotation < 20deg/sec)"," b) pre-arm check that accels are consistent (Pixhawk only, must be within 1m/sec/sec of each other)"," c) pre-arm check that gyros are consistent (Pixhawk only, must be within 20deg/sec of each other)"," d) report health of all accels and gyros (not just primary) to ground station ","------------------------------------------------------------------","ArduCopter 3.2-rc6 31-Aug-2014","Changes from 3.2-rc5 ","1) Spline twitch when passing through a waypoint largely resolved","2) THR_DZ param added to allow user configuration of throttle deadzone during AltHold, Loiter, PosHold","3) Landing check made more strict (climb rate must be -40~40cm/s for 1 full second)","4) LAND_REPOSITION param default set to 1","5) TradHeli with flybar passes through pilot inputs directly to swash when in ACRO mode","6) Safety Items:"," a) EKF check disabled when using inertial nav (caused too many false positives)"," b) pre-arm check of internal vs external compass direction (must be within 45deg of each other)","7) Bug Fixes:"," a) resolve NaN in angle targets when vehicle hits gimbal lock in ACRO mode"," b) resolve GPS driver buffer overflow that could lead to missed GPS messages on Pixhawk/PX4 boards"," c) resolve false \"compass not calibrated\" warnings on Pixhawk/PX4 caused by missing device id initialisation ","------------------------------------------------------------------","ArduCopter 3.2-rc5 15-Aug-2014","Changes from 3.2-rc4 ","1) Pixhawk's max num waypoints increased to 718","2) Smoother take-off in AltHold, Loiter, PosHold (including removing initial 20cm jump when taking off)","3) ACRO mode roll, pitch, yaw EXPO added for faster rotation when sticks are at extremes (see ACRO_EXPO parameter)","4) ch7/ch8 relay option replaces ch6 option (ch6 is reserved for tuning not switching things on/off)","5) Safety Items:"," a) Baro glitch check relaxed to 5m distance, 15m/s/s max acceleration"," b) EKF/INav check relaxed to 80cm/s/s acceleration correct (default remains as 0.6 but this now means 80cm/s/s)"," c) When GPS or Baro glitch clears, the inertial nav velocities are *not* reset reducing chance of sudden vehicle lean"," d) Baro altitude calculation checked for divide-by-zero and infinity","6) Bug Fixes:"," a) AltHold jump bug fixed (altitude target reset when landed)"," b) Rally point bug fix so it does not climb excessively before flying to rally point"," c) body-frame rate controller z-axis bug fix (fast rotation in z-axis would cause wobble in roll, pitch) ","------------------------------------------------------------------","ArduCopter 3.2-rc4 01-Aug-2014","Changes from 3.2-rc3","1) Pre-takeoff throttle feedback in AltHold, Loiter, PosHold","2) Terrain altitude retrieval from ground station (informational purposes only so far, Pixhawk only) ","3) Safety Items:"," a) \"EKF check\" will switch to LAND mode if EKF's compass or velocity variance over 0.6 (configurable with EKFCHECK_THRESH param)"," When EKF is not used inertial nav's accelerometer corrections are used as a substitute"," b) Barometer glitch protection added. BAROGLTCH_DIST and BAROGLTCH_ACCEL parameters control sensitivity similar to GPSGLITCH protection"," When glitching occurs barometer values are temporarily ignored"," c) Throttle/radio and battery failsafes now disarm vehicle when landed regardless of pilot's throttle position"," d) auto-disarm extended to Drift, Sport and OF_Loiter flight modes"," e) APM2 buzzer notification added for arming failure"," f) APM2 arming buzz made longer (now matches Pixhawk)"," g) do-set-servo commands cannot interfere with motor output","4) Bug Fixes:"," a) Drift slow yaw response fixed"," b) AC3.2-rc3 failsafe bug resolved. In -rc3 the throttle failsafe could be triggered even when disabled or motors armed (although vehicle would not takeoff) ","------------------------------------------------------------------","ArduCopter 3.2-rc3 16-Jul-2014","Changes from 3.2-rc2","1) Hybrid renamed to PosHold","2) Sonar (analog, i2c) and PulsedLight Range Finders enabled on Pixhawk (Allyson, Tridge)","3) Landing changes:"," a) disable pilot repositioning while landing in RTL, Auto (set LAND_REPOSITION to 1 to re-enable) (JonathanC)"," b) delay 4 seconds before landing due to failsafe (JonathanC)","4) Secondary compass calibration enabled, pre-arm check that offsets match current devices (Randy, Tridge, MichaelO)","5) Control improvements:"," a) use bias adjusted gyro rates - helps in cases of severe gyro drift (Jonathan)"," b) bug-fixes when feed-forward turned off (Leonard)","6) TradHeli improvements (RobL):"," a) bug fix to use full collective range in stabilize and acro flight modes"," b) filter added to main rotor input (ch8) to ensure momentary blip doesn't affect main rotor speed","7) Safety items:"," a) increased default circular Fence radius to 300m to reduce chance of breach when GPS lock first acquired"," b) radio failsafe timeout for late frames reduced to 0.5sec for normal receivers or 2.0sec when flying with joystick (Craig)"," c) accelerometer pre-arm check for all active accelerometers (previously only checked the primary accelerometer)","8) Other features:"," a) ch7/ch8 option to retract mount (svefro)"," b) Do-Set-ROI supported in Guided, RTL mode"," c) Condition-Yaw accepted in Guided, RTL modes (MoussSS)"," d) CAMERA dataflash message includes relative and absolute altitude (Craig)","9) Red Balloon Popper support (Randy, Leonard):"," a) Velocity controller added to Guided mode"," b) NAV_GUIDED mission command added","10) Bug fixes:"," a) bug fix to flip on take-off in stabilize mode when landing flag cleared slowly (JonathanC)"," b) allow disarming in AutoTune (JonathanC)"," c) bug fix to unpredictable behaviour when two spline points placed directly ontop of each other","------------------------------------------------------------------","ArduCopter 3.2-rc2 27-May-2014","Changes from 3.2-rc1","1) Hybrid mode initialisation bug fix","2) Throttle pulsing bug fix on Pixhawk","3) Parachute enabled on Pixhawk","4) Rally Points enabled on Pixhawk","------------------------------------------------------------------","ArduCopter 3.2-rc1 9-May-2014","Changes from 3.1.4","1) Hybrid mode - position hold mode but with direct response to pilot input during repositioning (JulienD, SandroT)","2) Spline waypoints (created by David Dewey, modified and integrated by Leonard, Randy)","3) Drift mode uses \"throttle assist\" for altitude control (Jason)","4) Extended Kalman Filter for potentially more reliable attitude and position control (Pixhawk only) (Paul Riseborough). Set AHRS_EKF_USE to 1 to enable or use Ch7/8 switch to enable/disable in flight. ","5) Manual flight smoothness:"," a) Smoother roll, pitch response using RC_FEEL_RP parameter (100 = crisp, 0 = extremely soft)"," b) Adjustable max rotation rate (ATC_RATE_RP_MAX, ATC_RATE_Y_MAX) and acceleration (ATC_ACCEL_RP_MAX, ATC_ACCEL_Y_MAX)","6) Autopilot smoothness:"," a) Vertical acceleration in AltHold, Loiter, Hybrid modes can be configured with PILOT_ACCEL_Z parameter (higher = faster acceleration)"," b) Maximum roll and pitch angle acceleration in Loiter mode can be configured with WPNAV_LOIT_JERK (higher = more responsive but potentially jerky)"," c) Yaw speed can be adjusted with ATC_SLEW_YAW parameter (higher = faster)"," d) smoother takeoff with configurable acceleration using WPNAV_ACCEL_Z parameter"," e) Twitches removed during guided mode or when entering Loiter or RTL from high speeds ","7) Mission improvements:"," a) mission will be resumed from last active command when pilot switches out and then back into Auto mode (prev behaviour can be restored by setting MIS_RESTART param to 1)"," b) DO_SET_ROI persistent across waypoints. All-zero DO_SET_ROI command restores default yaw behaviour"," c) do-jump fixed"," d) conditional_distance fixed"," e) conditional_delay fixed"," f) do-change-speed command takes effect immediately during mission"," g) vehicle faces directly at next waypoint (previously it could be about 10deg off)"," h) loiter turns fix to ensure it will circle around lat/lon point specified in mission command (previously it could be off by CIRCLE_RADIUS)","8) Safety improvements:"," a) After a fence breach, if the pilot re-takes control he/she will be given a minimum of 10 seconds and 20m to recover before the autopilot will invoke RTL or LAND"," b) Parachute support including automatic deployment during mechanical failures","9) Other enhancements:"," a) V-tail quad support"," b) Dual GPS support (secondary GPS output is simply logged, not actually used yet)"," c) Electro Permanent Magnet (aka Gripper) support"," d) Servo pass through for channels 6 ~ 8 (set RC6_FUNCTION to 1)"," e) Remove 80m limit on RTL's return altitude but never let it be above fence's max altitude","10) Other bug fixes:"," a) Bug fix for LAND sometimes getting stuck at 10m"," b) During missions, vehicle will maintain altitude even if WPNAV_SPEED is set above the vehicle's capabilities"," c) when autopilot controls throttle (i.e. Loiter, Auto, etc) vehicle will reach speeds specified in PILOT_VELZ_MAX and WPNAV_SPEED_UP, WPNAV_SPEED_DN parameters","11) CLI removed from APM1/2 to save flash space, critical functions moved to MAVLink:"," a) Individual motor tests (see MP's Initial Setup > Optional Hardware > Motor Test)"," b) compassmot (see MP's Initial Setup > Optional Hardware > Compass/Motor Calib)"," c) parameter reset to factory defautls (see MP's Config/Tuning > Full Parameter List > Reset to Default)","------------------------------------------------------------------","ArduCopter 3.1.5 27-May-2014 / 3.1.5-rc2 20-May-2014","Changes from 3.1.5-rc1","1) Bug Fix to broken loiter (pixhawk only)","2) Workaround to read from FRAM in 128byte chunks to resolve a few users boot issues (Pixhawk only)","------------------------------------------------------------------","ArduCopter 3.1.5-rc1 14-May-2014","Changes from 3.1.4","1) Bug Fix to ignore roll and pitch inputs to loiter controller when in radio failsafe","2) Bug Fix to allow compassmot to work on Pixhawk","------------------------------------------------------------------","ArduCopter 3.1.4 8-May-2014 / 3.1.4-rc1 2-May-2014","Changes from 3.1.3","1) Bug Fix for Pixhawk/PX4 NuttX I2C memory corruption when errors are found on I2C bus","------------------------------------------------------------------","ArduCopter 3.1.3 7-Apr-2014","Changes from 3.1.2","1) Stability patch fix which could cause motors to go to min at full throttle and with large roll/pitch inputs","------------------------------------------------------------------","ArduCopter 3.1.2 13-Feb-2014 / ArduCopter 3.1.2-rc2 12-Feb-2014","Changes from 3.1.2-rc1","1) GPS Glitch detection disabled when connected via USB","2) RC_FEEL_RP param added for adjusting responsiveness to pilot roll/pitch input in Stabilize, Drift, AltHold modes","------------------------------------------------------------------","ArduCopter 3.1.2-rc1 30-Jan-2014","Changes from 3.1.1","1) Pixhawk baro bug fix to SPI communication which could cause large altitude estimate jumps at high temperatures","------------------------------------------------------------------","ArduCopter 3.1.1 26-Jan-2014 / ArduCopter 3.1.1-rc2 21-Jan-2014","Changes from 3.1.1-rc1","1) Pixhawk improvements (available for APM2 when AC3.2 is released):"," a) Faster arming"," b) AHRS_TRIM fix - reduces movement in loiter when yawing"," c) AUX Out 5 & 6 turned into general purpose I/O pins"," d) Three more relays added (relays are pins that can be set to 0V or 5V)"," e) do-set-servo fix to allow servos to be controlled from ground station"," f) Motorsync CLI test"," g) PX4 parameters moved from SD card to eeprom"," h) additional pre-arm checks for baro & inertial nav altitude and lean angle","------------------------------------------------------------------","ArduCopter 3.1.1-rc1 14-Jan-2014","Changes from 3.1","1) Pixhawk improvements:"," a) Telemetry port 2 enabled (for MinimOSD)"," b) SD card reliability improvements"," c) parameters moved to FRAM"," d) faster parameter loading via USB"," e) Futaba SBUS receiver support","2) Bug fixes:"," a) Loiter initialisation fix (Loiter would act like AltHold until flight mode switch changed position)"," b) ROI commands were not returning Lat, Lon, Alt to mission planner when mission was loaded from APM","3) TradHeli only fixes:"," a) Drift now uses same (reduced) collective range as stabilize mode"," b) AutoTune disabled (for tradheli only)"," c) Landing collective (smaller than normal collective) used whenever copter is not moving","------------------------------------------------------------------","ArduCopter 3.1 14-Dec-2013","Changes from 3.1-rc8","1) Pixhawk improvements:"," a) switch to use MPU6k as main accel/gyro"," b) auto loading of IO-board firmware on startup","2) RTL fixes:"," a) initialise waypoint leash length (first RTL stop would be more aggressive than 2nd)"," b) reduce projected stopping distance for higher speed stops","------------------------------------------------------------------","ArduCopter 3.1-rc8 9-Dec-2013","Changes from 3.1-rc7","1) add Y6 motor mapping with all top props CW, bottom pros CCW (set FRAME = 10)","2) Safety Changes:"," a) ignore yaw input during radio failsafe (previously the copter could return home spinning if yaw was full over at time of failsafe)"," b) Reduce GPSGLITCH_RADIUS to 2m (was 5m) to catch glitches faster","3) Bug fixes:"," a) Optical flow SPI bus rates"," b) TradHeli main rotor ramp up speed fix","------------------------------------------------------------------","ArduCopter 3.1-rc7 22-Nov-2013","Changes from 3.1-rc6","1) MOT_SPIN_ARMED default to 70","2) Smoother inertial nav response to missed GPS messages","3) Safety related changes"," a) radio and battery failsafe disarm copter if landed in Loiter or AltHold (previously they would RTL)"," b) Pre-Arm check failure warning output to ground station every 30 seconds until they pass"," c) INS and inertial nav errors logged to dataflash's PM message"," d) pre-arm check for ACRO_BAL_ROLL, ACRO_BAL_PITCH","------------------------------------------------------------------","ArduCopter 3.1-rc6 16-Nov-2013","Improvements over 3.1-rc5","1) Heli improvements:"," a) support for direct drive tails (uses TAIL_TYPE and TAIL_SPEED parameters)"," b) smooth main rotor ramp-up for those without external govenor (RSC_RAMP_TIME)"," c) internal estimate of rotor speed configurable with RSC_RUNUP_TIME parameter to ensure rotor at top speed before starting missions"," d) LAND_COL_MIN collective position used when landed (reduces chance copter will push too hard into the ground when landing or before starting missions)"," e) reduced collective while in stabilize mode (STAB_COL_MIN, STAB_COL_MAX) for more precise throttle control"," f) external gyro parameter range changed from 1000~2000 to 0~1000 (more consistent with other parameters)"," g) dynamic flight detector switches on/off leaky-i term depending on copter speed","2) SingleCopter airframe support (contribution from Bill King)","3) Drift mode replaces TOY","4) MPU6k SPI bus speed decreased to 500khz after 4 errors","5) Safety related changes:"," a) crash detector cuts motors if copter upside down for more than 2 seconds"," b) INS (accel and gyro) health check in pre-arm checks"," c) ARMING_CHECK allows turning on/off individual checks for baro, GPS, compass, parameters, board voltage, radio"," d) detect Ublox GPS running at less than 5hz and resend configuration"," e) GPSGlitch acceptable radius reduced to 5m (stricter detection of glitches)"," f) range check roll, pitch input to ensure crazy radio values don't get through to stabilize controller"," g) GPS failsafe options to trigger AltHold instead of LAND or to trigger LAND even if in flight mode that does not require GPS"," h) Battery failsafe option to trigger RTL instead of LAND"," i) MOT_SPIN_ARMED set to zero by default","6) Bug fixes:"," a) missing throttle controller initialisation would mean Stabilize mode's throttle could be non-tilt-compensated"," b) inertial nav baro and gps delay compensation fix (contribution from Neurocopter)"," c) GPS failsafe was invoking LAND mode which still used GPS for horizontal control","------------------------------------------------------------------","ArduCopter 3.1-rc5 22-Oct-2013","Improvements over 3.1-rc4","1) Pixhawk USB reliability improvements","2) AutoTune changes:"," a) enabled by default"," b) status output to GCS"," c) use 2 pos switch only","3) ch7/ch8 LAND","4) Tricopter stability patch improvements [thanks to texlan]","5) safety improvements:"," a) slower speed up of motors after arming"," b) pre-arm check that copter is moving less than 50cm/s if arming in Loiter or fence enabled","------------------------------------------------------------------","ArduCopter 3.1-rc4 13-Oct-2013","Improvements over 3.1-rc3","1) Performance improvements to resolve APM alt hold issues for Octacopters:"," a) SPI bus speed increased from 500khz to 8Mhz"," b) Telemetry buffer increased to 512bytes"," c) broke up medium and slow loops into individual scheduled tasks and increased priority of alt hold tasks","2) Bug fix for Pixhawk USB connection","3) GPS Glitch improvements:"," a) added GPS glitch check to arming check"," b) parameters for vehicle max acceleration (GPSGLITCH_ACCEL) and always-ok radius (GPSGLICH_RADIUS)","------------------------------------------------------------------","ArduCopter 3.1-rc3 09-Oct-2013","Improvements over 3.1-rc2","1) GPS Glitch protection - gps positions are compared with the previous gps position. Position accepted if within 10m or copter could have reached the position with max accel of 10m/s/s.","2) Bug fix for pixhawk SPI bus contention that could lead to corrupted accelerometer values on pixhawk resolved","3) Auto Tuning (compile time option only add \"#define AUTOTUNE ENABLED\" to APM_Config.h and set CH7_Opt or CH8_Opt parameter to 17)","4) CPU Performance improvement when reading from MPU6k for APM","5) SUPER_SIMPLE parameter changed to a bit map to allow some flight modes to use super simpler while others use regular simple (MP release to allow easier selection will go out with AC3.1 official release)","6) Safety changes:"," a) safety button must be pushed before arming on pixhawk"," b) RGB LED (aka toshiba led) changed so that disarmed flashes, armed is either blue (if no gps lock) or green (if gps lock)"," c) sensor health bitmask sent to groundstations","------------------------------------------------------------------","ArduCopter 3.1-rc2 18-Sep-2013","Improvements over 3.1-rc1","1) bug fix for MOT_SPIN_ARMED to allow it to be higher than 127","2) PX4/pixhawk auto-detect internal/external compass so COMPASS_ORIENT should be set to ORIENTATION_NONE if using GPS+compass module","------------------------------------------------------------------","ArduCopter 3.1-rc1 9-Sep-2013","Improvements over 3.0.1","1) Support for Pixhawks board","2) Arm, Disarm, Land and Takeoff in Loiter and AltHold","3) Improved Acro"," a) ACRO_RP_P, ACRO_YAW_P parameters added to control speed of rotation"," b) ACRO_BAL_ROLL, ACRO_BAL_PITCH controls speed at which copter returns to level"," c) ACRO_TRAINER can be set to 0:disable trainer, 1:auto leveling when sticks released, 2:auto leveling and lean angle limited to ANGLE_MAX"," d) Ch7 & Ch8 switch to set ACRO_TRAINER options in-flight","4) SPORT mode - equivalent of earth frame Acro with support for simple mode","5) Sonar ground tracking improvements and bug fixes that reduce reaction to bad sonar data","6) Safety improvements"," a) motors always spin when armed (speed can be controlled with MOT_SPIN_ARMED, set to 0 to disable)"," b) vehicle's maximum lean angle can be reduced (or increased) with the ANGLE_MAX parameter"," c) arming check that GPS hdop is > 2.0 (disable by setting GPS_HDOP parameter to 900)"," d) slow take-off in AUTO, LOITER, ALTHOLD to reduce chance of motor/esc burn-out on large copters","7) Bug fixes:"," a) Optical flow sensor initialisation fix"," b) altitude control fix for Loiter_turns mission command (i.e. mission version of CIRCLE mode)"," c) DO_SET_ROI fix (do not use \"ROI\")","8) Distribute Loiter & Navigation calcs over 4 cycles to reduce impact on a single 100hz loop","9) RCMAP_ parameters allow remapping input channels 1 ~ 4","------------------------------------------------------------------","ArduCopter 3.0.1-rc2 / 3.0.1 11-Jul-2013","Improvements over 3.0.1-rc1","1) Rate Roll, Pitch and Yaw I fix when we hit motor limits","2) pre-arm check changes:"," a) double flash arming light when pre-arm checks fail"," b) relax mag field checks to 35% min, 165% max of expected field","3) loiter and auto changes:"," a) reduced Loiter speed to 5 m/s"," b) reduced WP_ACCEL to 1 m/s/s (was 2.5 m/s/s)"," c) rounding error fix in loiter controller"," d) bug fix to stopping point calculation for RTL and loiter during missions","4) Stability Patch fix which was freezing Rate Taw I term and allowing uncommanded Yaw","------------------------------------------------------------------","ArduCopter 3.0.1-rc1 26-Jun-2013","Improvements over 3.0.0","1) bug fix to Fence checking position after GPS lock was lost","2) bug fix to LAND so that it does not attempt to maintain horizontal position without GPS lock","------------------------------------------------------------------","ArduCopter 3.0.0 / 3.0.0-rc6 16-Jun-2013","Improvements over 3.0.0-rc5","1) bug fix to Circle mode's start position (was moving to last loiter target)","2) WP_ACCEL parameter added to allow user to adjust acceleration during missions","3) loiter acceleration set to half of LOIT_SPEED parameter value (was hard-coded)","4) reduce AltHold P to 1.0 (was 2.0)","------------------------------------------------------------------","ArduCopter 3.0.0-rc5 04-Jun-2013","Improvements over 3.0.0-rc4","1) bug fix to LAND flight mode in which it could try to fly to mission's next waypoint location","2) bug fix to Circle mode to allow counter-clockwise rotation","3) bug fix to heading change in Loiter, RTL, Missions when pilot's throttle is zero","4) bug fix for mission sticking at take-off command when pilot's throttle is zero","5) bug fix for parameters not saving when new value is same as default value","6) reduce pre-arm board min voltage check to 4.3V (was 4.5V)","7) remove throttle controller's ability to limit lean angle in loiter, rtl, auto","------------------------------------------------------------------","ArduCopter 3.0.0-rc4 02-Jun-2013","Improvements over 3.0.0-rc3","1) loiter improvements:"," i) repositioning enhanced with feed forward"," ii) use tan to convert desired accel to lean angle","2) stability patch improvements for high powered copters or those with roll-pitch rate gains set too high","3) auto mode vertical speed fix (it was not reaching the desired speeds)","4) alt hold smoothed by filtering feed forward input","5) circle mode fix to initial position and smoother initialisation","6) RTL returns to initial yaw heading before descending","7) safe features:"," i) check for gps lock when entering failsafe"," ii) pre-arm check for mag field lenght"," iii) pre-arm check for board voltage between 4.5v ~ 5.8V"," iv) beep twice during arming"," v) GPS failsafe enabled by default (will LAND if loses GPS in Loiter, AUTO, Guided modes)"," vi) bug fix for alt-hold mode spinning motors before pilot has raised throttle","8) bug fixes:"," i) fixed position mode so it responding to pilot input"," ii) baro cli test"," iii) moved cli motor test to test sub menu and minor change to throttle output"," iv) guided mode yaw control fix","------------------------------------------------------------------","ArduCopter 3.0.0-rc3 22-May-2013","Improvements over 3.0.0-rc2","1) bug fix for dataflash erasing unnecessarily","2) smoother transition to waypoints, loiter:"," intermediate point's speed initialised from copter's current speed","3) Ch8 auxiliary function switch (same features as Ch7)","4) safety checks:"," Warning to GCS of reason for pre-arm check failure"," ARMING_CHECK parameter added to allow disabling pre-arm checks"," Added compass health and offset check to pre-arm check"," compassmot procedure displays interference as percentage of total mag field","5) WPNAV dataflash message combined into NTUN message","6) allow TriCopters to use ESC calibration","------------------------------------------------------------------","ArduCopter 3.0.0-rc2 13-May-2013","Improvements over 3.0.0-rc1:","1) smoother transition to waypoints, loiter:"," reduced loiter max acceleration to smooth waypoints"," bug fix to uninitialised roll/pitch when entering RTL, AUTO, LOITER","2) fast waypoints - copter does not stop at waypoints unless delay is specified","3) WPNAV_LOIT_SPEED added to allow faster/slower loiter repositioning","4) removed speed limits on auto missions","5) enhance LAND mission command takes lat/lon coordinates","6) bug fix for RTL not pointing home sometimes","7) centrifugal correction disabled when copter is disarmed to stop HUD moving","8) centrifugal correction disabled when sat count less than 6 (AHRS_GPS_MINSATS)","9) compass calibration reliability improvements when run from mission planner","10) bug fix to allow compassmot to be run from mission planner terminal screen","11) add support for H-quad frame","12) add COMPASS_ORIENT parameter to support external compass in any orientation","------------------------------------------------------------------","ArduCopter 3.0.0-rc1 01-May-2013","Improvements over 2.9.1b:","1) Inertial navigation for X & Y axis (Randy/Leonard/Jonathan)","2) 3D waypoint navigation library (Leonard/Randy)"," WPNAV_SPEED, WPNAV_SPEED_UP, WPNAV_SPEED_DN control target speeds during missions and RTL"," WP_YAW_BEHAVIOR to allow disabling yaw during missions and RTL","3) PX4 support (some features still not available) (Tridge/Pat/PX4Dev Team)","4) Safety improvements:"," Tin-can shaped fence (set FENCE_ENABLED to 1 and copter will RTL if alt > 150m or horizontal distance from home > 300m) (Randy/Tridge/Leonard)"," GCS failsafe (set FS_GCS_ENABLED to 1 and if you are using a tablet to fly your copter it will RTL and return control to the radio 3 seconds after losing telemetry) (Randy)"," pre-arm checks to ensure accelerometer and radio calibration has been performed before arming (Randy)","5) motor interference compensation for compass (Jonathan/Randy)","6) Circle mode improvements:"," set CIRCLE_RADIUS to zero to do panorama shots in circle mode (copter does not move in a circle but instead slowly rotates)"," CIRCLE_RATE parameter allows controlling direction and speed of rotation in CIRCLE mode and LOITER_TURNS (can also be adjusted in flight from CH6 knob)","7) SONAR_GAIN parameter add to allow reducing the response to objects sensed by sonar (Randy)","8) support for trapezoidal quads (aka V shaped or FPV quads) (Leonard/Craig)","9) performance improvements to dataflash logging (Tridge)","10) bug-fix to analog read which could cause bad sonar reads when using voltage or current monitor (Tridge)","11) bug-fix to motors going to minimum when throttle is low while switching into Loiter, AUTO, RTL, ALT_HOLD (Jason/Randy)","12) bug-fix for auto disarm sometimes disarming shortly after arming (Jason/SirAlex)","------------------------------------------------------------------","ArduCopter 2.9.1b 30-Feb-2013","Improvements over 2.9.1:","1) reduce INS_MPU6K_FILTER to 20hz","2) reduce InertialNav Z-axis time constant to 5 (was 7)","3) increased max InertialNav accel correction to 3 m/s (was 1m/s)","4) bug fix for alt_hold being passed as int16_t to get_throttle_althold_with_slew","5) bug fix for throttle after acro flip (was being kept at min throttle if pilot switched out of ACRO mode while inverted)","6) reduce yaw_rate P default to 0.20 (was 0.25)","------------------------------------------------------------------","ArduCopter 2.9.1 & 2.9.1-rc2 01-Feb-2013","Improvements over 2.9.1-rc1:","1) small corretion to use of THR_MID to scale lower end of manual throttle between THR_MIN and 500 instead of 0 and 500","2) bug fix for longitude scaling being incorrectly calculated using Next Waypoint instead of home which could lead to scaling being 1","3) ESC calibration change to set update rate to ESCs to 50hz to allow simonk ESC to be calibrated","------------------------------------------------------------------","ArduCopter 2.9.1-rc1 31-Jan-2013","Improvements over 2.9:","1) THR_MID parameter added to allow users to adjust the manual throttle so that vehicle hovers at about mid stick","2) bug fix for autotrim - roll axis was backwards","3) bug fix to set sonar_alt_health to zero when sonar is disabled","4) capture level roll and pitch trims as part of accel calibration","5) bug fix to ppm encoder false positives","------------------------------------------------------------------","ArduCopter 2.9 & 2.9-rc5 14-Jan-2013","Improvements over 2.9-rc4:","1) add constraint to loiter commanded roll and pitch angles","2) relax altitude requirement for take-off command to complete","------------------------------------------------------------------","ArduCopter 2.9-rc4 12-Jan-2013","Improvements over 2.9-rc3:","1) Smoother transition between manual and auto flight modes (Leonard)","2) bug fix for LAND not actually landing when initiated from failsafe (Randy/Craig)","------------------------------------------------------------------","ArduCopter 2.9-rc3 11-Jan-2013","Improvements over 2.9-rc2:","1) alt hold with sonar improvements - now on by default (Leonard/Randy)","2) performance and memory useage improvements (Tridge/Randy)","3) increase APM1 baro pressure read from 5hz to 8.3hz to improve alt hold (Randy)","4) bug fix: altitude error reported to GCS (Randy)","5) limit inertial nav's max accel offset correction to 100cm/s/s to speed up recovery after hard impacts (Randy)_","6) moved rate controllers to run after ins read (Tridge/Randy)","------------------------------------------------------------------","ArduCopter 2.9-rc2 31-Dec-2012","Improvements over 2.9-rc1:","1) increased throttle rate gains from 1.0 to 6.0","2) APM1 fix so it works with inertial nav (5hz update rate of baro was beyond the tolerance set in the inav library)","------------------------------------------------------------------","ArduCopter 2.9-rc1 23-Dec-2012","Improvements over 2.8.1:","1) altitude hold improvements:"," a)inertial navigation for vertical axis [Randy/Jonathan/Leonard/Jason]"," b)accel based throttle controller [Leonard/Randy]"," c)accelerometer calibration routine updated to use gauss-newton method [Randy/Tridge/Rolfe Schmidt]"," d)parameters to control climb rate:"," AUTO_VELZ_MIN, AUTO_VELZ_MAX - allows you to control the maximum climb and descent rates of the autopilot (in cm/s)"," PILOT_VELZ_MAX - allows you to control the maximum climb/descent rate when in alt hold or loiter (in cm/s)","2) landing improvements [Leonard/Randy]"," LAND_SPEED - allows you to set the landing speed in cm/s","3) camera related improvements:"," a) AP_Relay enabled for APM2 and integrated with AP_Camera [Sandro Benigno]"," b) camera trigger with channel 7 switch or DO_DIGICAM_CONTROL mission command [Randy]"," c) allow yaw override by pilot or with CONDITIONAL_YAW command during missions [Randy]"," YAW_OVR_BEHAVE - Controls when autopilot takes back normal control of yaw after pilot overrides (0=after next wp, 1=never)","4) trad heli improvements [Rob]"," a) code tested and brought back into the fold (2.8.1 was never released for trad helis)"," b) enabled rate controller (previously only used angle controllers)"," c) fix to rotor speed controllers - now operates by switching off channel 8"," d) allow wider collective pitch range in acro and alt hold modes vs stabilize mode"," e) removed angle boost function because it created more problems than it solved"," f) bug fix to allow collective pitch to use the entire range of servos","5) mediatek gps driver improvements [Craig]"," a) added support for 1.9 firmware"," b) bug fix to start-up routine so sbas can be enabled","6) failsafe improvements (both throttle and battery) [Randy/Craig/John Arne Birkeland]"," a) RTL will not trigger if your throttle is zero - reduces risk of accidentally invoking RTL if you switch off your receiver before disarming"," b) failsafe triggered in unlikely case of a PPM encoder failure"," c) bug fix to resolve motors momentarily reducing to zero after failsafe is triggered","7) mpu6k filtering made configurable and default changed to 42hz for copters [Leonard/Tridge]","8) support ppm sum for transmitters with as few as 5 channels [Randy/John Arne Birkeland]","9) acro trainer - copter will return to be generally upright if you release the sticks in acro mode [Leonard]"," ACRO_BAL_ROLL, ACRO_BAL_PITCH - controls rate at which roll returns to level"," ACRO_TRAINER - 1 to enable the auto-bring-upright feature","10) other changes and bug fixes:"," a) allow >45 degrees when in stabilize mode by adding lines like below to APM_Config (compile time option only) [Jason]"," #define MAX_INPUT_ROLL_ANGLE 6000 // 60 degrees"," #define MAX_INPUT_PITCH_ANGLE 6000 // 60 degrees"," b) bug fix to stop RTL from ever climbing to an unreasonable height (i.e. >80m) [Jason]"," c) event and state logging [Jason]"," d) allow cli to be used over telemetry link [Tridge]"," e) bug fix to allow compass accumulate to run when we have spare cpu cycles [Randy]"," f) bug fix so do_set_servo command works [Randy]"," g) bug fix to PID controller's so they don't calculate crazy D term on the first call [Tridge]"," h) bug fix to initialise navigation parameter to resolve twitch when entering some navigation modes [Jason]"," i) performance improvement to copter leds - use DigitalFastWrite and DigitalFastRead instead of native arduino functions [Randy]"," j) removed unused stab_d from roll and pitch controller [Jason]"," k) bug fix for guided mode not reaching target altitude if it reaches horizontal target first [Randy]"," l) code clean-up, parameter documentation improvements [Randy/Jason/Rob/others]","","------------------------------------------------------------------","ArduCopter 2.8.1 22-Oct-2012","Improvements over 2.8:","- 430 bytes of RAM freed up to resolve APM1 level issue and reduce chance of memory corruption on both APM1 and APM2","","Improvements over 2.7.3:","- Improved ACRO mode (Leonard Hall)","- Improved stability patch to reduce \"climb-on-yaw\" problem (Leonard, Rob Lefebvre, Randy)","- Rate controller targets moved to body frames (yaw control now works properly when copter is inverted) (Leonard/Randy)","- Less bouncy Stabilize yaw control (Leonard)","- OpticalFlow sensor support for APM2.5 (Randy)","- DMP works again by adding \"#define DMP_ENABLED ENABLED\" to APM_Config.h You can also log DMP vs DCM to the dataflash by adding \"#define SECONDARY_DMP_ENABLED ENABLED\" (Randy)","- Watch dog added to shutdown motors if main loop feezes for 2 seconds (Randy)","- Thrust curve added to linearize pwm->thrust. Removes deadzone found above 90% throttle in most ESC/motors (Randy)","- More timing improvements (main loop is now tied to MPU6000s interrupt) (Randy)","- GPS NMEA bug fix (Alexey Kozin)","- Logging improvements (log I terms, dump all settings at head of dataflash log) (Jason)","","Bug Fixes / Parameter changes:","- fixed skipping of last waypoint (Jason)","- resolved twitching when no GPS attached (Tridge)","- fixed loss of altitude if alt hold is engaged before first GPS lock (Randy/Jason)","- moved Roll-Pitch I terms from Stabilize controllers to Rate controllers","- TILT_COMPENSATION param tuned for TradHeli (Rob)","","Code Cleanup:","- HAL changes for platform portability (Pat Hickey)","- Removed INSTANT_PWM (Randy)","------------------------------------------------------------------"],"stylingDirectives":[[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[],[]],"colorizedLines":null,"csv":null,"csvError":null,"dependabotInfo":{"showConfigurationBanner":false,"configFilePath":null,"networkDependabotPath":"/ArduPilot/ardupilot/network/updates","dismissConfigurationNoticePath":"/settings/dismiss-notice/dependabot_configuration_notice","configurationNoticeDismissed":null},"displayName":"ReleaseNotes.txt","displayUrl":"https://github.com/ArduPilot/ardupilot/blob/ArduCopter-3.2.1/ArduCopter/ReleaseNotes.txt?raw=true","headerInfo":{"blobSize":"40.8 KB","deleteTooltip":"You must be signed in to make or propose changes","editTooltip":"You must be signed in to make or propose changes","ghDesktopPath":"https://desktop.github.com","isGitLfs":false,"onBranch":true,"shortPath":"5c3ba48","siteNavLoginPath":"/login?return_to=https%3A%2F%2Fgithub.com%2FArduPilot%2Fardupilot%2Fblob%2FArduCopter-3.2.1%2FArduCopter%2FReleaseNotes.txt","isCSV":false,"isRichtext":false,"toc":null,"lineInfo":{"truncatedLoc":"650","truncatedSloc":"646"},"mode":"file"},"image":false,"isCodeownersFile":null,"isPlain":false,"isValidLegacyIssueTemplate":false,"issueTemplate":null,"discussionTemplate":null,"language":"Text","languageID":372,"large":false,"planSupportInfo":{"repoIsFork":null,"repoOwnedByCurrentUser":null,"requestFullPath":"/ArduPilot/ardupilot/blob/ArduCopter-3.2.1/ArduCopter/ReleaseNotes.txt","showFreeOrgGatedFeatureMessage":null,"showPlanSupportBanner":null,"upgradeDataAttributes":null,"upgradePath":null},"publishBannersInfo":{"dismissActionNoticePath":"/settings/dismiss-notice/publish_action_from_dockerfile","releasePath":"/ArduPilot/ardupilot/releases/new?marketplace=true","showPublishActionBanner":false},"rawBlobUrl":"https://github.com/ArduPilot/ardupilot/raw/ArduCopter-3.2.1/ArduCopter/ReleaseNotes.txt","renderImageOrRaw":false,"richText":null,"renderedFileInfo":null,"shortPath":null,"symbolsEnabled":true,"tabSize":4,"topBannersInfo":{"overridingGlobalFundingFile":false,"globalPreferredFundingPath":null,"showInvalidCitationWarning":false,"citationHelpUrl":"https://docs.github.com/github/creating-cloning-and-archiving-repositories/creating-a-repository-on-github/about-citation-files","actionsOnboardingTip":null},"truncated":false,"viewable":true,"workflowRedirectUrl":null,"symbols":{"timed_out":false,"not_analyzed":true,"symbols":[]}},"copilotInfo":null,"copilotAccessAllowed":false,"csrf_tokens":{"/ArduPilot/ardupilot/branches":{"post":"7Fs3ltqw0K-1tyECeTpibzi0PjZ2qyOLCtl3uxNN6bW7phX72fxt3Y1__6TPaKS6w2C4IKS4HRZ-BmPBpZ9rqQ"},"/repos/preferences":{"post":"4xrP1Fedo70gFs0WXnvszg_ZHX-SKgBOWg86FsqvIl5fGx1L3obobAiyOTUQB91LvXHHtvJENBB7YY_AcMXyig"}}},"title":"ardupilot/ArduCopter/ReleaseNotes.txt at ArduCopter-3.2.1 ยท ArduPilot/ardupilot"}