Skip to content
nnaufel edited this page Nov 1, 2021 · 94 revisions
Clone this wiki locally

Arrow DataStorm DAQ Development Platform featuring technology from Analog Devices® & Intel®

Overview

This site provides content on how to create new FMC Card reference designs or access to completed reference designs for the DataStorm DAQ platform. The DataStorm DAQ features an Intel® Cyclone™ V SoC FPGA with a dual core ARM Cortex™-A9 processors and logic.

Developers of new FMC Card reference designs are provided with step by step instruction for both hardware and software build flows.

Completed reference designs are provided with a Quick Start guide, Platform Architectural descriptions, and instructions on how to rebuild the design. Complete bootable SD card images are also provided for each reference design. The table below, show a list of the completed designs.

Table of Contents

  1. Introduction
  2. Prerequisites for Developers *** Do this first if intentions are to build any of the designs ***
  3. Developer Starter Guides
  4. Additional Developer Documentation
  5. Completed Reference Designs
  6. Terms of Use

Introduction

The DataStorm DAQ (Trenz Electronic TE0022-03) is an SoC board based on Intel Cyclone V FPGA, an ethernet PHY, 1 GB DDR3 SDRAM per HPS and FPGA, and one 32 MB Quad SPI Flash memory for configuration and operation per HPS and FPGA, and powerful switching-mode power supplies for all on-board voltages.

Key Features

SoC FPGA

  • Intel Cyclone® V (5CSEMA5F31C8N)
  • Package: FBGA 896 pins
  • Speed Grade: 8
  • Temperature: Commercial (Tj = 0 °C to 85 °C)

Memory/Storage

  • 1 GB DDR3 SDRAM for HPS
  • 1 GB DDR3 SDRAM for FPGA
  • 32 MB SPI for HPS
  • 32 MB SPI for FPGA

On Board

  • up to 7 x SMA Connector
  • Temperature Sensor
  • Intel MAX®10 for board management

Interfaces

  • LPC FMC Connector
  • 4 x PMOD Connector
  • JTAG
  • UART via micro USB B Connector (for FPGA)
  • UART via micro USB B Connector (for HPS)
  • 4 x USB 2.0 Host
  • Ethernet via RJ45 Connector
  • SD Card
  • HDMI output

Power

  • 12 V Input supply voltage

Developer Starter Guides

These starter guides guide developers through the process of creating their own reference designs for the DataStorm DAQ and act as a starting point for future customization.

Additional Developer Documentation

Completed Reference Designs

The following platforms are ready to be used in their existing state and do not require additional development effort

Terms of Use

YOU TAKE ALL SUCH PRODUCTS AND SERVICES “AS-IS” WITHOUT ANY WARRANTY. THERE ARE NO REPRESENTATIONS OR WARRANTIES OF ANY KIND BY SELLER, EXPRESS OR IMPLIED, AS TO THE CONDITION OR PERFORMANCE OF ANY PRODUCTS OR SERVICES, THEIR MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR USE, NON-INFRINGEMENT, OR OTHERWISE. SELLER ASSUMES NO RESPONSIBILITY OR LIABILITY FOR SUPPLIERS’ PRODUCT OR SERVICE SPECIFICATIONS OR THE PERFORMANCE OR ADEQUACY OF ANY DESIGN OR SPECIFICATION PROVIDED TO SELLER.

All rights in intellectual property owned or licensed by Seller or Supplier are hereby reserved and deemed restricted or limited. Seller makes no representation or warranty with respect to such rights and will have no liability in connection with them. You agree to comply with all requirements with regard to any intellectual property (including any requirement to enter into a separate license agreement and prohibitions against duplicating, reverse engineering, or disclosing the same). You shall indemnify Seller against and defend and hold it harmless from all liability, cost, or expense arising out of or relating to any (a) breach or alleged breach of these terms and conditions, (b) allegation or claim, including infringement claims, that arise from Your use of Products or services in combination with other products or services, or (c) alleged or actual infringement of any intellectual property rights provided by You to Seller.



Return - Table of Contents
Return - Top of Page