Skip to content
No description, website, or topics provided.
Branch: master
Clone or download
Fetching latest commit…
Cannot retrieve the latest commit at this time.
Permalink
Type Name Latest commit message Commit time
Failed to load latest commit information.
digilent-vivado-scripts @ fd7ce6b
proj
repo
sdk
src
.gitignore
.gitmodules
README.md
project_info.tcl

README.md

Nexys A7-50T GPIO Demo

Description

This project is a Vivado demo using the Nexys A7-50T's switches, LEDs, RGB LED's, pushbuttons, seven-segment display, PWM audio output, PDM microphone and USB UART bridge, written in VHDL. When programmed onto the board, all sixteen of the switches are tied to their corresponding LEDs. Every time a switch is toggled, the LED directly above it will toggle with it. If the center push button is pressed, all the LEDs will be tied to ground. The two tri-color LEDs are set to gradually change colors at all times.

The seven segment display counts up from 0 to 9 as long as no buttons are pressed. As long as BTNU is pressed, the first digit on the seven segment display is turned off. In the same manner, BTNL turns off the second digit, BTNR turns off the third, and BTND turns off the fourth. BTNC turns off the entire display and resets the counter. The microphone which is next to Pmod connector JC, records audio data and sends it to the mono audio output located at J8. To listen to the mics output, you will need to plug in headphones or a speaker.

To use the USB-UART bridge feature of this demo, the Nexys A7-50T must be connected to a serial terminal on the computer it is connected to over the MicroUSB cable. For more information on how to set up and use a serial terminal, such as Tera Term or PuTTY, refer to this tutorial. Whenever the reset button or BTNC is pressed, the Nexys A7-50T sends the line “Nexys A7-50T GPIO/UART DEMO!” to the serial terminal. Whenever one of the D-pad buttons other than BTNC is pressed, the line “Button press detected!” is sent.

Button Function
BTNC Turns off the entire seven-segment display and resets the counter
Prints "Nexys A7-50T GPIO/UART DEMO!" through theUSB-UART bridge
BTNU Turns off the first digit on seven-segment display
Prints "Button press detected!" through the USB-UART bridge
BTNL Turns off the second digit on seven-segment display
Prints "Button press detected!" through theUSB-UART bridge
BTNR Turns off the third digit on seven-segment display
Prints "Button press detected!" through the USB-UART bridge
BTND Turns off the fourth digit on seven-segment display
Prints "Button press detected!" through the USB-UART bridge

Requirements

Demo Setup

  1. Download and extract the most recent release ZIP archive from this repository's Releases Page.
  2. Open the project in Vivado 2018.2 by double clicking on the included XPR file found at "<archive extracted location>/vivado_proj/Nexys-A7-50T-GPIO.xpr".
  3. In the Flow Navigator panel on the left side of the Vivado window, click Open Hardware Manager.
  4. Plug the Nexys A7-50T into the computer using a MicroUSB cable.
  5. Open a serial terminal emulator (such as TeraTerm) and connect it to the Nexys A7-50T's serial port, using a baud rate of 9600.
  6. In the green bar at the top of the Vivado window, click Open target. Select Auto connect from the drop down menu.
  7. In the green bar at the top of the Vivado window, click Program device.
  8. In the Program Device Wizard, enter "<archive extracted location>vivado_proj/Nexys-A7-50T-GPIO.runs/impl_1/top.bit" into the "Bitstream file" field. Then click Program.
  9. The demo will now be programmed onto the Nexys A7-50T. See the Description section of this README to learn how to interact with this demo.

Next Steps

This demo can be used as a basis for other projects, either by adding sources included in the demo's release to those projects, or by modifying the sources in the release project.

Check out the Nexys A7-50T's Resource Center to find more documentation, demos, and tutorials.

For technical support or questions, please post on the Digilent Forum.

Additional Notes

For more information on how this project is version controlled, refer to the Digilent Vivado Scripts Repository

You can’t perform that action at this time.