Pillar drill

Guy Fraser edited this page May 9, 2017 · 6 revisions

NuTool Group CH10

Quick links: UsageTroubleshootingMaintenance

Nickname Make Model Where Manual Issue Tracker Status
? NuTool Group CH10 [[Workshop Rooms]] see note below Tool: Drill - Nutool CH10

We couldn't find a manual for this make and model, but there's a Draper drill that looks very similar, so here's the manual for that. If you can find the proper manual, please let us know!

Overview

This machine, a manual 5-speed drill press (sometimes called a "pillar drill"), is used to make vertical holes in pretty much anything.

It's useful for small ad-hoc jobs. For higher volume production consider using a mill, and for higher accuracy consider using a laser cutter.

How it works

It's a very old and rattly machine but very useful when you need it.

You put a bit in the chuck, tighten the chuck with a key, and then start the drill. Place your material on the drill bed and position it roughly under the drill bit. Use the levers on the drill to bring the drill bit closer to your material, but not touching, then adjust the position of the material so the drill bit is exactly over where you want to drill. Now you can lower the drill to make the hole, and then raise it up again quite a bit afterwards so it's not getting in the way of moving your material. Repeat as necessary.

Please remove the bit when you are done and put it back where you found it, or the next person (who will not know where it belongs) will put it aside and it will get lost.

Specifications

TO-DO

History

TO-DO

Using the machine

Training required: need info

To use this machine, you'll need to:

  • Follow safety precautions
  • Obtain materials
  • Prepare drill
  • Drill holes
  • Reset drill

Let's get started...

Safety precautions

With a high speed rotating drill bit, this machine poses serious risk of injury.

Class Orange Equipment

  • Workshop Safety
  • Always turn off the drill when not in use
  • Never leave the drill unattended
  • ...

Step 1: Obtain materials

need infos on what materials can be drilled, where to get them

Step 1: Prepare drill

  • You'll need a drill bit - they are in the drawer near the drill
    • need info about what drill bit to use for different materials, etc
  • Use the chuck key (it's usually attached to the drill by a bit of wire) to tighten the drill bit in the chuck

Depending on the height of your material, you'll want to use either the base table or the moveable one that slides up and down.

  • If using the base table, swing the other one sideways so it's not getting in the way
  • If using the other table, you can move it up and down, left or right, using the quick-release lever on the right
    • ⚠️ Make sure the drill bit still lines up with the hole in the table!
    • Using the three-pronged rotating levers, move the drill but towards the table to make sure it's lined up with, and easily goes in to, the hole in the table
  • Using the three-pronged rotating levers on the right side, raise the drill bit upwards so there's enough room to place your materials under it
  • If the table hole is too big to support the material you are drilling, you can put some scrap wood under your material to support it

Step 2: Drill holes

need info here about speed setting; small diameter drills may need higher speeds

  • Turn on the drill via the buttons on the left side
  • Place your material on the platform
    • If it's a big piece of material, get someone to assist you - don't risk injury!
  • To drill a hole:
    • Use the rotating levers on the right to bring the bit closer to your material, but not touching
    • Reposition your material as necessary so the drill bit is directly above where you want to drill
    • Slowly lower the drill bit in to your material to make the hole
    • Once the hole is made, raise the drill bit up again to leave plenty of room for moving your material
  • Repeat as necessary for any additional holes

Step 3: Reset the drill

  • Turn off the drill using the button on the left side
  • Wait for the chuck and bit to stop spinning - ensure they are completely stopped
  • Carefully remove your material and place on a nearby workbench or table
  • Using the chuck key, loosen the chuck and retrieve the drill bit
    • ⚠️ The drill bit may be very hot - be careful!
  • Put the drill bit back in the drawer so it doesn't get lost

Returning the drill bit to the drawer, rather than just leaving it in the drill, has proved a reliable way of reducing the number of bits that go missing. Please make sure you return it to the drawer!

Hints & Tips

TO-DO

Minimising waste

  • Avoid: don't create useless stuff!
  • Reduce: how to minimise materials used?
  • Reuse: can waste be reused?
  • Upcycle: can waste be upcycled to something else?
  • Recycle: Depending on the material, you might be able to recycle it in the bins near the kitchen.
  • Disposal: For any remaining waste, please put it in the workshop bin.
  • General: Waste, recycling and cleaning up

Troubleshooting

If the advice below doesn't solve the problem, please create a new issue to let us know.

TO-DO

Maintenance

  • If the machine is broken or needs maintenance, create an issue in the issue tracker (link in Troubleshooting above)
    • Label the issue: Tool: Drill - Nutool CH10 as applicable
    • If broken, add Broken label (this triggers various systems to flag the machine unavailable)
    • If maintenance required, add Maintenance label (the machine is working, but needs TLC)
    • If parts or consumables need purchasing, add Shopping label
  • There is a belt between different pulleys under the top cover that sometimes needs ajusting
  • where spare parts are stored?
  • where to buy spare parts?
  • where to buy consumables?

See also

  • Wikipedia: Drill Press
  • Tool: CNC Mill - Proxxon
  • Tool: CNC Mill - Arcitype
  • Tool: Laser Cutter - Small (Sophia)
  • Tool: Laser Cutter - Large (Gerald)
Clone this wiki locally
You can’t perform that action at this time.
You signed in with another tab or window. Reload to refresh your session. You signed out in another tab or window. Reload to refresh your session.
Press h to open a hovercard with more details.