Skip to content

Latest commit

 

History

History
157 lines (99 loc) · 5.45 KB

install.md

File metadata and controls

157 lines (99 loc) · 5.45 KB

Installing Rad Pro on the FNIRSI GC-01/JOY-IT JT-RAD01

This guide explains how to install Rad Pro on FNIRSI GC-01 and JOY-IT JT-RAD01 Geiger counters.

What You'll Need

  • A USB data cable (charging-only cables will not work)
  • A Windows 10 or Windows 11 computer

⚠️ Use a Windows 10/11 computer. macOS and Linux are not supported for installation. If something goes wrong on an unsupported OS, recovery requires a Windows machine.

Step 1: Download the Firmware

  1. Go to the Rad Pro releases page: https://github.com/Gissio/radpro/releases
  2. Download the latest radpro-[version].zip.
  3. Extract the archive on your computer.

Step 2: Flash Rad Pro

  1. Make sure your device is powered off.

  2. Connect it to your computer using the USB data cable.

  3. A USB drive should appear.

    If no drive appears, your device may be incompatible. See Troubleshooting below.

  4. Open the extracted firmware folder: fnirsi-gc01_[microprocessor]/firmware/ and choose the correct firmware file: radpro-fnirsi-gc01_[microprocessor]-[language]-x.y.z-install.bin

    • [microprocessor] is apm32f103rbt6 or ch32f103r8t6. Start with apm32f103rbt6. If you get a Drive full error, disconnect the device and retry using ch32f103r8t6.
    • [language] is a two-letter code (e.g., en, es)
  5. Copy the file to the USB drive.

The device will automatically reboot when the transfer completes.

After reboot, Rad Pro is installed.

Troubleshooting

Device not detected:

  • Make sure your USB cable supports data transfer
  • Try another USB port
  • Try a USB hub
  • Hold Right/Settings + OK/Power to expose the USB drive
  • After plugging in, press the reset switch (located near the USB connector, opposite the charge LED)

Installation fails:

  • Try another USB port
  • Try a USB hub
  • Hold OK/Power before plugging in the USB cable, and keep holding throughout the process
  • If the file copy seems to succeed but the device doesn't reboot correctly, try copying the file a second time

Want to restore the original firmware?

  • Copy the stock firmware from the firmware folder to the device using the same process

Still no joy?

Step 3: Basic Controls

Once installed, here are the essential controls:

Navigation

  • Press Up / Down: Change measurement mode / navigate menus
  • Press Right: Select / open settings
  • Press Left: Go back

System

  • Hold OK: Power on/off
  • Hold Left + OK: Toggle lock mode

Measurement Screen

  • Press Left: Switch secondary display
  • Hold Left: Reset measurement / dismiss alerts
  • Hold Right: Toggle pulse sound
  • Press OK: Turn off display

Random generator

  • Press Right: Restart random generator

Step 4: First Configuration

Check that background radiation readings are in the expected range of ~0.05–0.25 µSv/h.

If readings are too low:

  1. Open Settings > Geiger tube > Tube type
  2. Select HH614

Step 5: Finish Up

Hardware Notes

CH32F103R8 (WCH) Devices

Data Storage Capacity

Rad Pro stores up to 5,075 measurements.

At typical background radiation (~20 CPM), this corresponds to:

  • 60-minute interval: ~105 days
  • 10-minute interval: ~17 days
  • 1-minute interval: ~84 hours
  • 10-second interval: ~14 hours
  • 1-second interval: ~84 minutes

High Voltage (HV) Profiles

  • Factory default: 9.207 kHz frequency, 75% duty cycle

APM32F103R8 (Geehy) Devices

Data Storage Capacity

Rad Pro stores up to 72,065 measurements.

At typical background radiation (~20 CPM), this corresponds to:

  • 60-minute interval: ~1502 days
  • 10-minute interval: ~250 days
  • 1-minute interval: ~50 days
  • 10-second interval: ~8 days
  • 1-second interval: ~20 hours