Skip to content
Permalink
Branch: master
Find file Copy path
Find file Copy path
Fetching contributors…
Cannot retrieve contributors at this time
112 lines (97 sloc) 3.7 KB
/*
* autolight.h
*
* Project: autolight
* Author: NStorm
* License: Apache License Version 2.0, January 2004 http://www.apache.org/licenses/
* https://github.com/N-Storm/autolight
*/
#ifndef AUTOLIGHT_H_
#define AUTOLIGHT_H_
// Settings. PS = proximity sensor, AL = ambient light.
// Trigger interrupt/closed state when proximity value crosses PROX_TH
#define PROX_TH 30
// Set light on if CH0-CH1*2 less than that value (integer math approximation)
#define LIGHT_TH 100
// Delay in ms between measuring AL/PS during working state
#define DELAY 600
/* Uncomment line below to enable AL level reevaluating during working state.
* Enabling this will allow light to turn on/off due to the changes in AL level.
*/
// #define RECHECK_AL
// Uncomment to enable MCU internal pull-up on INT pin
// #define INT_PULLUP
// Expert settings below. It's recommended to leave defaults.
// Wait time 202 ms
#define WTIME_DEFAULT 0xB6
// PS Pulse count
#define PPULSE_DEFAULT 4
// PPERS = 3 consecutive PS values out of range
#define PERS_CON 0b00110000
// ALS Timing recommended ~50ms value, 19 cyc, 51.87ms
#define ATIME_DEFAULT 0xED
// PS Timing, recommended to be set to 0xFF (1 cyc, 10 bits)
#define PTIME_DEFAULT 0xFF
// Addresses and registers. 7-bit address value shifted left to MSB.
#define APDS_ADDR (0x39 << 1)
#define APDS_ENABLE 0x00
#define APDS_ATIME 0x01
#define APDS_PTIME 0x02
#define APDS_WTIME 0x03
#define APDS_PILTL 0x08
#define APDS_PILTH 0x09
#define APDS_PIHTL 0x0A
#define APDS_PIHTH 0x0B
#define APDS_PERS 0x0C
#define APDS_CONFIG 0x0D
#define APDS_PPULSE 0x0E
#define APDS_CONTROL 0x0F
#define APDS_ID 0x12
#define APDS_ALS 0x14
#define APDS_Ch0DATAL 0x14
#define APDS_Ch0DATAH 0x15
#define APDS_Ch1DATAL 0x16
#define APDS_Ch1DATAH 0x17
#define APDS_PROX 0x18
#define APDS_PDATAL 0x18
#define APDS_PDATAH 0x19
#define APDS_ID_VAL 0x39
// Enable register flags
#define SAI (1<<6) // Sleep after interrupt. When asserted, the device will power down at the end of a proximity or ALS cycle if an interrupt has been generated.
#define PIEN (1<<5) // Proximity Interrupt Mask. When asserted, permits proximity interrupts to be generated.
#define AIEN (1<<4) // ALS Interrupt Mask. When asserted, permits ALS interrupt to be generated.
#define WEN (1<<3) // Enable Wait
#define PEN (1<<2) // Enable Prox
#define AEN (1<<1) // Enable ALS
#define PON (1<<0) // Enable Power On
// Control register flags
// #define PDRIVE 0 // 100mA of LED Power
#define PDRIVE 0x80 // 25mA of LED Power
#define PDIODE 0x20 // CH1 Diode
#define PGAIN 0x00 // 1x Prox gain
#define AGAIN 0x01 // 8x ALS gain
// Command register flags
#define APDS_RESET_PROX_INT 0b11100101
#define REPEATED_BYTE 0x80
#define AUTO_INCREMENT 0xA0
#define SPECIAL_FN 0xE0
// States
#define RS_START 0
#define RS_SLEEP 1
#define RS_WAKE 2
#define RS_LOWLIGHT 3
#define RS_HIGHLIGHT 4
#define RS_CLOSED 5
// Utility macros
#define DNOP() _NOP(); _NOP();
#define QNOP() DNOP(); DNOP();
/* Define 2 macros here to enable/disable output to MOSFET on PB3 with pull-up.
* Using additional internal pullup to drive high level instead of only output high due to
* PB3 pin has lower drive capability because it's also act as the RESET pin which
* should be able to accept +12V during programming conditions and it will provide only
* ~ +2.7V high output with Vcc at +3.3V. With pull-up enabled we can get ~ +3.2V output.
*/
#define LIGHTON() do { PORTB |= (1 << PB3); PUEB |= (1 << PUEB3); } while (0);
#define LIGHTOFF() do { PUEB &= ~(1 << PUEB3); PORTB &= ~(1 << PB3); } while (0);
#define CCP_MAGIC 0xD8 // Magic number to enable configuration access
#endif /* AUTOLIGHT_H_ */
You can’t perform that action at this time.