Skip to content
Permalink
Browse files

remove non ASCII characters

small typo
  • Loading branch information...
nechry committed Mar 16, 2019
1 parent 8b00f02 commit 057c4f0a548b97af3d52f3ca39c4b006c8dec4e6
Showing with 27 additions and 27 deletions.
  1. +1 −1 config/philio/pan05.xml
  2. +11 −9 config/tronika/zv9040.xml
  3. +15 −17 config/tronika/zv9101.xml
@@ -15,7 +15,7 @@
<Item label="Switch On" value="2" />
</Value>
<Value type="list" genre="config" instance="1" index="3" label="Manual On/Off mode" min="0" max="1" value="1" size="1">
<Help>The On/Off function of S1S2 and learn switch can be disabled or enabled by this parameter, default value is Enable. But the learning operation won’t be affected. When manual On/Off function is disabled, the RF command can only switch On but not Off. This is useful function for keeping the device in switch on state</Help>
<Help>The On/Off function of S1,S2 and learn switch can be disabled or enabled by this parameter, default value is Enable. But the learning operation wont be affected. When manual On/Off function is disabled, the RF command can only switch On but not Off. This is useful function for keeping the device in switch on state</Help>
<Item label="Disable manual On/Off" value="0" />
<Item label="Enable manual On/Off" value="1" />
</Value>
@@ -9,7 +9,8 @@
<CommandClass id="112">
<Value type="list" genre="config" instance="1" index="2" label="Saving state before power failure" size="1" value="1">
<Help>
Saving state before power failure. Default Not saved.
Saving state before power failure.
Default Not saved.
</Help>
<Item label="State NOT saved at power failure, all outputs are set to OFF upon power restore" value="0"/>
<Item label="State NOT saved at power failure, all outputs are set to ON upon power restore" value="1"/>
@@ -24,16 +25,16 @@
<Item label="Enable" value="1"/>
</Value>
<Value type="byte" genre="config" instance="1" index="4" label="Fade time" min="0" max="255" value="1">
<Help>Fade time (units betwen 1-127 represent 1-127 seconds.
Units Betwen 128-244 represent minutes, 128 = 1 minute, 129 = 2 minutes..
<Help>Fade time (units between 1-127 represent 1-127 seconds.
Units Betwen 128-244 represent minutes, 128 = 1 minute, 129 = 2 minutes.
This value has the same function as Duration of Multilevel).
Default 1.
</Help>
</Value>
<Value type="byte" genre="config" instance="1" index="5" label="Setting minimum brightness value" min="0" max="50" value="0">
<Help>Setting minimum brightness value.
Valid value: 0 - 50, the bigger the value is, the higher the load’s minimum brightness is.
Note: when configure this value, the value of Multilevel will be configured as 1 automatically so that users can preview the corre-sponding effect of minimum brightness value
Valid value: 0 - 50, the bigger the value is, the higher the loads minimum brightness is.
Note: when configure this value, the value of Multilevel will be configured as 1 automatically so that users can preview the corresponding effect of minimum brightness value
</Help>
</Value>
<Value type="byte" genre="config" instance="1" index="6" label="Setting maximum brightness value" min="0" max="100" value="100">
@@ -60,14 +61,15 @@
</Value>
<Value type="list" genre="config" instance="1" index="9" label="External switch to be added to and removed from a network" size="1" value="1">
<Help>Enable/disable external switch to be added to and removed from a network.
When enables this function, triple press the external switch within 1.5 seconds to be added to or removed from a net-work. Defaul Enabled.
When enables this function, triple press the external switch within 1.5 seconds to be added to or removed from a net-work.
Default Enabled.
</Help>
<Item label="Disable" value="0"/>
<Item label="Enable" value="1"/>
</Value>
<Value type="list" genre="config" instance="1" index="10" label="Detect load after re-power on" size="1" value="0">
<Help>
Enable/disable to detect laod after re-power on (detect load type, minimum brightness, maximum brightness)
Enable/disable to detect load after re-power on (detect load type, minimum brightness, maximum brightness)
</Help>
<Item label="Disable" value="0"/>
<Item label="Enable to detect every time after re-power on" value="1"/>
@@ -100,13 +102,13 @@
<Value type="short" genre="config" instance="1" index="14" label="Power automatic report absolute threshold" size="2" units="W" value="10">
<Help>
Power automatic report absolute threshold, unit is W.
When power changes above the absolute threhold, immediately report current power value
When power changes above the absolute threshold, immediately report current power value
</Help>
</Value>
<Value type="byte" genre="config" instance="1" index="15" label="Power automatic report percentage threshold" size="1" units="%" value="20">
<Help>
Power automatic report percentage threshold, unit is %.
When power changes above the percentage threhold, immediately report current power value
When power changes above the percentage threshold, immediately report current power value
</Help>
</Value>
<Value type="int" genre="config" instance="1" index="21" label="Power metering automatich report time cycle" size="4" units="second" value="600">
@@ -15,27 +15,25 @@
<Item label="State NOT saved at power failure, all outputs are set to ON upon power restore" value="1"/>
<Item label="State saved at power failure, all outputs are set to previous state upon power restore" value="2"/>
</Value>
<Value type="list" genre="config" instance="1" index="3" label="Enable/disable to send the basic report" size="1" value="1">
<Value type="list" genre="config" instance="1" index="3" label="Send the basic report" size="1" value="1">
<Help>Enable/disable to send the basic report to the Lifeline when the load state changed.
When value set as 1, re-power on the dimmer, it will send Basic report automatically. Default Enabled.
When value set as 1, re-power on the dimmer, it will send Basic report automatically.
Default Enabled.
</Help>
<Item label="Disable to send Basic report" value="0"/>
<Item label="Enable to send Basic report" value="1"/>
<Item label="Disable" value="0"/>
<Item label="Enable" value="1"/>
</Value>
<Value type="byte" genre="config" instance="1" index="4" label="Fade time." min="0" max="255" value="1">
<Help>Fade time (units betwen 1-127 represent 1-127 seconds. Units Betwen 128-244 represent minutes, 128 = 1 minute, 129 = 2 minutes..
This value has the same function as Duration of Multilevel). Default 1.
<Value type="byte" genre="config" instance="1" index="4" label="Fade time" min="0" max="255" value="1">
<Help>Fade time (units between 1-127 represent 1-127 seconds.
Units Between 128-244 represent minutes, 128 = 1 minute, 129 = 2 minutes.
This value has the same function as Duration of Multilevel).
Default 1.
</Help>
</Value>
<Value type="byte" genre="config" instance="1" index="5" label="Setting minimum brightness value" min="0" max="50" value="0">
<Help>Setting minimum brightness value
Valid value: 0 - 50, the bigger the value is, the
higher the load’s minimum brightness is.

Note: when configure this value, the value of
Multilevel will be configured as 1 automatically
so that users can preview the corre-sponding
effect of minimum brightness value
<Help>Setting minimum brightness value.
Valid value: 0 - 50, the bigger the value is, the higher the loads minimum brightness is.
Note: when configure this value, the value of Multilevel will be configured as 1 automatically so that users can preview the corresponding effect of minimum brightness value
</Help>
</Value>
<Value type="list" genre="config" instance="1" index="6" label="Choose MOSFET driving type" size="1" value="1">
@@ -47,8 +45,8 @@
</Value>
<Value type="list" genre="config" instance="1" index="7" label="Enable/disable external switch to be added to and removed from a network" size="1" value="1">
<Help>Enable/disable external switch to be added to and removed from a network.
When enables this function, triple press the external switch within 1.5 seconds
to be added to or removed from a net-work. Defaul Enabled.
When enables this function, triple press the external switch within 1.5 seconds to be added to or removed from a net-work.
Default Enabled.
</Help>
<Item label="Disable" value="0"/>
<Item label="Enable" value="1"/>

0 comments on commit 057c4f0

Please sign in to comment.
You can’t perform that action at this time.