diff --git a/boards/micoair/h743/bootloader.px4board b/boards/micoair/h743/bootloader.px4board new file mode 100644 index 000000000000..19b6e662be69 --- /dev/null +++ b/boards/micoair/h743/bootloader.px4board @@ -0,0 +1,3 @@ +CONFIG_BOARD_TOOLCHAIN="arm-none-eabi" +CONFIG_BOARD_ARCHITECTURE="cortex-m7" +CONFIG_BOARD_ROMFSROOT="" diff --git a/boards/micoair/h743/default.px4board b/boards/micoair/h743/default.px4board new file mode 100644 index 000000000000..98d8f08aaf05 --- /dev/null +++ b/boards/micoair/h743/default.px4board @@ -0,0 +1,85 @@ +CONFIG_BOARD_TOOLCHAIN="arm-none-eabi" +CONFIG_BOARD_ARCHITECTURE="cortex-m7" +CONFIG_BOARD_SERIAL_URT6="/dev/ttyS5" +CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS2" +CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS0" +CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS1" +CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS3" +CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6" +CONFIG_BOARD_SERIAL_RC="/dev/ttyS4" +CONFIG_DRIVERS_ADC_BOARD_ADC=y +CONFIG_DRIVERS_BAROMETER_DPS310=y +CONFIG_DRIVERS_DSHOT=y +CONFIG_DRIVERS_GPS=y +CONFIG_DRIVERS_IMU_BOSCH_BMI088=y +CONFIG_DRIVERS_IMU_BOSCH_BMI270=y +CONFIG_COMMON_INS=y +CONFIG_COMMON_MAGNETOMETER=y +CONFIG_DRIVERS_OSD_ATXXXX=y +CONFIG_DRIVERS_PPS_CAPTURE=y +CONFIG_DRIVERS_PWM_OUT=y +CONFIG_COMMON_RC=y +CONFIG_DRIVERS_RC_INPUT=y +CONFIG_DRIVERS_TAP_ESC=y +CONFIG_COMMON_TELEMETRY=y +CONFIG_DRIVERS_UAVCAN=y +CONFIG_BOARD_UAVCAN_INTERFACES=1 +CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y +CONFIG_MODULES_BATTERY_STATUS=y +CONFIG_MODULES_COMMANDER=y +CONFIG_MODULES_CONTROL_ALLOCATOR=y +CONFIG_MODULES_DATAMAN=y +CONFIG_MODULES_EKF2=y +CONFIG_MODULES_ESC_BATTERY=y +CONFIG_MODULES_EVENTS=y +CONFIG_MODULES_FLIGHT_MODE_MANAGER=y +CONFIG_MODULES_FW_ATT_CONTROL=y +CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y +CONFIG_MODULES_FW_POS_CONTROL=y +CONFIG_MODULES_FW_RATE_CONTROL=y +CONFIG_MODULES_GYRO_CALIBRATION=y +CONFIG_MODULES_GYRO_FFT=y +CONFIG_MODULES_LAND_DETECTOR=y +CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y +CONFIG_MODULES_LOAD_MON=y +CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=y +CONFIG_MODULES_LOGGER=y +CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y +CONFIG_MODULES_MANUAL_CONTROL=y +CONFIG_MODULES_MAVLINK=y +CONFIG_MODULES_MC_ATT_CONTROL=y +CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y +CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y +CONFIG_MODULES_MC_POS_CONTROL=y +CONFIG_MODULES_MC_RATE_CONTROL=y +CONFIG_MODULES_NAVIGATOR=y +CONFIG_MODULES_PAYLOAD_DELIVERER=y +CONFIG_MODULES_RC_UPDATE=y +CONFIG_MODULES_ROVER_POS_CONTROL=y +CONFIG_MODULES_SENSORS=y +CONFIG_MODULES_TEMPERATURE_COMPENSATION=y +CONFIG_MODULES_UXRCE_DDS_CLIENT=y +CONFIG_MODULES_VTOL_ATT_CONTROL=y +CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y +CONFIG_SYSTEMCMDS_DMESG=y +CONFIG_SYSTEMCMDS_DUMPFILE=y +CONFIG_SYSTEMCMDS_FAILURE=y +CONFIG_SYSTEMCMDS_GPIO=y +CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y +CONFIG_SYSTEMCMDS_I2CDETECT=y +CONFIG_SYSTEMCMDS_NSHTERM=y +CONFIG_SYSTEMCMDS_PARAM=y +CONFIG_SYSTEMCMDS_PERF=y +CONFIG_SYSTEMCMDS_REBOOT=y +CONFIG_SYSTEMCMDS_SD_BENCH=y +CONFIG_SYSTEMCMDS_SD_STRESS=y +CONFIG_SYSTEMCMDS_SERIAL_PASSTHRU=y +CONFIG_SYSTEMCMDS_SERIAL_TEST=y +CONFIG_SYSTEMCMDS_SYSTEM_TIME=y +CONFIG_SYSTEMCMDS_TOP=y +CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y +CONFIG_SYSTEMCMDS_TUNE_CONTROL=y +CONFIG_SYSTEMCMDS_UORB=y +CONFIG_SYSTEMCMDS_USB_CONNECTED=y +CONFIG_SYSTEMCMDS_VER=y +CONFIG_SYSTEMCMDS_WORK_QUEUE=y diff --git a/boards/micoair/h743/extras/micoair_h743_bootloader.bin b/boards/micoair/h743/extras/micoair_h743_bootloader.bin new file mode 100644 index 000000000000..ca8c51127966 Binary files /dev/null and b/boards/micoair/h743/extras/micoair_h743_bootloader.bin differ diff --git a/boards/micoair/h743/firmware.prototype b/boards/micoair/h743/firmware.prototype new file mode 100644 index 000000000000..92f78470517d --- /dev/null +++ b/boards/micoair/h743/firmware.prototype @@ -0,0 +1,13 @@ +{ + "board_id": 1166, + "magic": "PX4FWv1", + "description": "Firmware for the MicoAir743 board", + "image": "", + "build_time": 0, + "summary": "MicoAir743", + "version": "0.1", + "image_size": 0, + "image_maxsize": 1835008, + "git_identity": "", + "board_revision": 0 +} diff --git a/boards/micoair/h743/init/rc.board_defaults b/boards/micoair/h743/init/rc.board_defaults new file mode 100644 index 000000000000..c915812e0065 --- /dev/null +++ b/boards/micoair/h743/init/rc.board_defaults @@ -0,0 +1,24 @@ +#!/bin/sh +# +# board specific defaults +#------------------------------------------------------------------------------ +param set-default BAT1_A_PER_V 40 +param set-default BAT1_N_CELLS 4 +param set-default BAT1_V_CHARGED 4.2 +param set-default BAT1_V_DIV 21.2 +param set-default BAT1_V_EMPTY 3.2 + +param set-default SYS_HAS_MAG 1 +param set-default PWM_MAIN_TIM0 -4 +param set-default RC_INPUT_PROTO -1 + +param set-default IMU_GYRO_RATEMAX 2000 +param set-default SYS_AUTOSTART 4001 +param set-default MC_PITCHRATE_K 0.4 +param set-default MC_ROLLRATE_K 0.35 +param set-default MC_YAWRATE_K 1.2 +param set-default MC_YAWRATE_MAX 360 +param set-default MAV_TYPE 2 +param set-default CA_AIRFRAME 0 +param set-default CA_ROTOR_COUNT 4 +param set-default CBRK_SUPPLY_CHK 894281 diff --git a/boards/micoair/h743/init/rc.board_extras b/boards/micoair/h743/init/rc.board_extras new file mode 100644 index 000000000000..549676dd7df5 --- /dev/null +++ b/boards/micoair/h743/init/rc.board_extras @@ -0,0 +1,7 @@ +#!/bin/sh +# +# board specific extras init +#------------------------------------------------------------------------------ + +# enable onboard OSD chip +atxxxx start -s diff --git a/boards/micoair/h743/init/rc.board_sensors b/boards/micoair/h743/init/rc.board_sensors new file mode 100644 index 000000000000..96273de2da8b --- /dev/null +++ b/boards/micoair/h743/init/rc.board_sensors @@ -0,0 +1,18 @@ +#!/bin/sh +# +# board specific sensors init +#------------------------------------------------------------------------------ + +board_adc start + +# # Internal SPI bus BMI088 accel/gyro +bmi088 -s -b 2 -A -R 6 start +bmi088 -s -b 2 -G -R 6 start + +# # Internal SPI bus BMI270 accel/gyro +bmi270 -s -b 2 -R 0 start + +# Internal baro +dps310 -I start -a 118 + +ist8310 -I -R 2 start diff --git a/boards/micoair/h743/nuttx-config/bootloader/defconfig b/boards/micoair/h743/nuttx-config/bootloader/defconfig new file mode 100644 index 000000000000..76254f132727 --- /dev/null +++ b/boards/micoair/h743/nuttx-config/bootloader/defconfig @@ -0,0 +1,89 @@ +# +# This file is autogenerated: PLEASE DO NOT EDIT IT. +# +# You can use "make menuconfig" to make any modifications to the installed .config file. +# You can then do "make savedefconfig" to generate a new defconfig file that includes your +# modifications. +# +# CONFIG_DEV_CONSOLE is not set +# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set +# CONFIG_SPI_EXCHANGE is not set +# CONFIG_STM32H7_SYSCFG is not set +CONFIG_ARCH="arm" +CONFIG_ARCH_BOARD_CUSTOM=y +CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/micoair/h743/nuttx-config" +CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y +CONFIG_ARCH_BOARD_CUSTOM_NAME="px4" +CONFIG_ARCH_CHIP="stm32h7" +CONFIG_ARCH_CHIP_STM32H743VI=y +CONFIG_ARCH_CHIP_STM32H7=y +CONFIG_ARCH_INTERRUPTSTACK=768 +CONFIG_ARMV7M_BASEPRI_WAR=y +CONFIG_ARMV7M_ICACHE=y +CONFIG_ARMV7M_MEMCPY=y +CONFIG_ARMV7M_USEBASEPRI=y +CONFIG_BOARDCTL=y +CONFIG_BOARDCTL_RESET=y +CONFIG_BOARD_ASSERT_RESET_VALUE=0 +CONFIG_BOARD_INITTHREAD_PRIORITY=254 +CONFIG_BOARD_LATE_INITIALIZE=y +CONFIG_BOARD_LOOPSPERMSEC=95150 +CONFIG_BOARD_RESET_ON_ASSERT=2 +CONFIG_C99_BOOL8=y +CONFIG_CDCACM=y +CONFIG_CDCACM_IFLOWCONTROL=y +CONFIG_CDCACM_PRODUCTID=0x004b +CONFIG_CDCACM_PRODUCTSTR="MicoAir743" +CONFIG_CDCACM_RXBUFSIZE=600 +CONFIG_CDCACM_TXBUFSIZE=12000 +#TODO：ally for VENDOR ID in the future +CONFIG_CDCACM_VENDORID=0x3162 +CONFIG_CDCACM_VENDORSTR="MicoAir" +CONFIG_DEBUG_FULLOPT=y +CONFIG_DEBUG_SYMBOLS=y +CONFIG_DEBUG_TCBINFO=y +CONFIG_DEFAULT_SMALL=y +CONFIG_EXPERIMENTAL=y +CONFIG_FDCLONE_DISABLE=y +CONFIG_FDCLONE_STDIO=y +CONFIG_HAVE_CXX=y +CONFIG_HAVE_CXXINITIALIZE=y +CONFIG_IDLETHREAD_STACKSIZE=750 +CONFIG_INIT_ENTRYPOINT="bootloader_main" +CONFIG_INIT_STACKSIZE=3194 +CONFIG_LIBC_FLOATINGPOINT=y +CONFIG_LIBC_LONG_LONG=y +CONFIG_LIBC_STRERROR=y +CONFIG_MEMSET_64BIT=y +CONFIG_MEMSET_OPTSPEED=y +CONFIG_PREALLOC_TIMERS=50 +CONFIG_PTHREAD_STACK_MIN=512 +CONFIG_RAM_SIZE=245760 +CONFIG_RAM_START=0x20010000 +CONFIG_RAW_BINARY=y +CONFIG_SERIAL_TERMIOS=y +CONFIG_SIG_DEFAULT=y +CONFIG_SIG_SIGALRM_ACTION=y +CONFIG_SIG_SIGUSR1_ACTION=y +CONFIG_SIG_SIGUSR2_ACTION=y +CONFIG_SPI=y +CONFIG_STACK_COLORATION=y +CONFIG_START_DAY=30 +CONFIG_START_MONTH=11 +CONFIG_STDIO_BUFFER_SIZE=32 +CONFIG_STM32H7_BKPSRAM=y +CONFIG_STM32H7_DMA1=y +CONFIG_STM32H7_OTGFS=y +CONFIG_STM32H7_PROGMEM=y +CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y +CONFIG_STM32H7_TIM1=y +CONFIG_SYSTEMTICK_HOOK=y +CONFIG_SYSTEM_CDCACM=y +CONFIG_TASK_NAME_SIZE=24 +CONFIG_TTY_SIGINT=y +CONFIG_TTY_SIGINT_CHAR=0x03 +CONFIG_TTY_SIGTSTP=y +CONFIG_USBDEV=y +CONFIG_USBDEV_BUSPOWERED=y +CONFIG_USBDEV_MAXPOWER=500 +CONFIG_USEC_PER_TICK=1000 diff --git a/boards/micoair/h743/nuttx-config/include/board.h b/boards/micoair/h743/nuttx-config/include/board.h new file mode 100644 index 000000000000..9c30129d3889 --- /dev/null +++ b/boards/micoair/h743/nuttx-config/include/board.h @@ -0,0 +1,426 @@ +/************************************************************************************ + * nuttx-configs/px4_fmu-v6u/include/board.h + * + * Copyright (C) 2016-2019 Gregory Nutt. All rights reserved. + * Authors: David Sidrane + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ************************************************************************************/ +#ifndef __NUTTX_CONFIG_MICOAIR743_INCLUDE_BOARD_H +#define __NUTTX_CONFIG_MICOAIR743_INCLUDE_BOARD_H + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +#include "board_dma_map.h" + +#include + +#ifndef __ASSEMBLY__ +# include +#endif + +#include "stm32_rcc.h" +#include "stm32_sdmmc.h" + +/************************************************************************************ + * Pre-processor Definitions + ************************************************************************************/ + +/* Clocking *************************************************************************/ +/* The MicoAir743 board provides the following clock sources: + * + * X1: 8 MHz crystal for HSE + * + * So we have these clock source available within the STM32 + * + * HSI: 64 MHz RC factory-trimmed + * HSE: 8 MHz crystal for HSE + */ + +#define STM32_BOARD_XTAL 8000000ul + +#define STM32_HSI_FREQUENCY 16000000ul +#define STM32_LSI_FREQUENCY 32000 +#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL +#define STM32_LSE_FREQUENCY 32768 + +/* Main PLL Configuration. + * + * PLL source is HSE = 8,000,000 + * + * PLL_VCOx = (STM32_HSE_FREQUENCY / PLLM) * PLLN + * Subject to: + * + * 1 <= PLLM <= 63 + * 4 <= PLLN <= 512 + * 150 MHz <= PLL_VCOL <= 420MHz + * 192 MHz <= PLL_VCOH <= 836MHz + * + * SYSCLK = PLL_VCO / PLLP + * CPUCLK = SYSCLK / D1CPRE + * Subject to + * + * PLLP1 = {2, 4, 6, 8, ..., 128} + * PLLP2,3 = {2, 3, 4, ..., 128} + * CPUCLK <= 480 MHz + */ + +#define STM32_BOARD_USEHSE + +#define STM32_PLLCFG_PLLSRC RCC_PLLCKSELR_PLLSRC_HSE + +/* PLL1, wide 4 - 8 MHz input, enable DIVP, DIVQ, DIVR + * + * PLL1_VCO = (8,000,000 / 1) * 120 = 960 MHz + * + * PLL1P = PLL1_VCO/2 = 960 MHz / 2 = 480 MHz + * PLL1Q = PLL1_VCO/4 = 960 MHz / 4 = 240 MHz + * PLL1R = PLL1_VCO/8 = 960 MHz / 8 = 120 MHz + */ + +#define STM32_PLLCFG_PLL1CFG (RCC_PLLCFGR_PLL1VCOSEL_WIDE | \ + RCC_PLLCFGR_PLL1RGE_4_8_MHZ | \ + RCC_PLLCFGR_DIVP1EN | \ + RCC_PLLCFGR_DIVQ1EN | \ + RCC_PLLCFGR_DIVR1EN) +#define STM32_PLLCFG_PLL1M RCC_PLLCKSELR_DIVM1(1) +#define STM32_PLLCFG_PLL1N RCC_PLL1DIVR_N1(120) +#define STM32_PLLCFG_PLL1P RCC_PLL1DIVR_P1(2) +#define STM32_PLLCFG_PLL1Q RCC_PLL1DIVR_Q1(4) +#define STM32_PLLCFG_PLL1R RCC_PLL1DIVR_R1(8) + +#define STM32_VCO1_FREQUENCY ((STM32_HSE_FREQUENCY / 1) * 120) +#define STM32_PLL1P_FREQUENCY (STM32_VCO1_FREQUENCY / 2) +#define STM32_PLL1Q_FREQUENCY (STM32_VCO1_FREQUENCY / 4) +#define STM32_PLL1R_FREQUENCY (STM32_VCO1_FREQUENCY / 8) + +/* PLL2 */ + +#define STM32_PLLCFG_PLL2CFG (RCC_PLLCFGR_PLL2VCOSEL_WIDE | \ + RCC_PLLCFGR_PLL2RGE_4_8_MHZ | \ + RCC_PLLCFGR_DIVP2EN | \ + RCC_PLLCFGR_DIVQ2EN | \ + RCC_PLLCFGR_DIVR2EN) +#define STM32_PLLCFG_PLL2M RCC_PLLCKSELR_DIVM2(2) +#define STM32_PLLCFG_PLL2N RCC_PLL2DIVR_N2(48) +#define STM32_PLLCFG_PLL2P RCC_PLL2DIVR_P2(2) +#define STM32_PLLCFG_PLL2Q RCC_PLL2DIVR_Q2(2) +#define STM32_PLLCFG_PLL2R RCC_PLL2DIVR_R2(2) + +#define STM32_VCO2_FREQUENCY ((STM32_HSE_FREQUENCY / 2) * 48) +#define STM32_PLL2P_FREQUENCY (STM32_VCO2_FREQUENCY / 2) +#define STM32_PLL2Q_FREQUENCY (STM32_VCO2_FREQUENCY / 2) +#define STM32_PLL2R_FREQUENCY (STM32_VCO2_FREQUENCY / 2) + +/* PLL3 */ + +#define STM32_PLLCFG_PLL3CFG (RCC_PLLCFGR_PLL3VCOSEL_WIDE | \ + RCC_PLLCFGR_PLL3RGE_4_8_MHZ | \ + RCC_PLLCFGR_DIVQ3EN) +#define STM32_PLLCFG_PLL3M RCC_PLLCKSELR_DIVM3(2) +#define STM32_PLLCFG_PLL3N RCC_PLL3DIVR_N3(48) +#define STM32_PLLCFG_PLL3P RCC_PLL3DIVR_P3(2) +#define STM32_PLLCFG_PLL3Q RCC_PLL3DIVR_Q3(4) +#define STM32_PLLCFG_PLL3R RCC_PLL3DIVR_R3(2) + +#define STM32_VCO3_FREQUENCY ((STM32_HSE_FREQUENCY / 2) * 48) +#define STM32_PLL3P_FREQUENCY (STM32_VCO3_FREQUENCY / 2) +#define STM32_PLL3Q_FREQUENCY (STM32_VCO3_FREQUENCY / 4) +#define STM32_PLL3R_FREQUENCY (STM32_VCO3_FREQUENCY / 2) + +/* SYSCLK = PLL1P = 480MHz + * CPUCLK = SYSCLK / 1 = 480 MHz + */ + +#define STM32_RCC_D1CFGR_D1CPRE (RCC_D1CFGR_D1CPRE_SYSCLK) +#define STM32_SYSCLK_FREQUENCY (STM32_PLL1P_FREQUENCY) +#define STM32_CPUCLK_FREQUENCY (STM32_SYSCLK_FREQUENCY / 1) + +/* Configure Clock Assignments */ + +/* AHB clock (HCLK) is SYSCLK/2 (240 MHz max) + * HCLK1 = HCLK2 = HCLK3 = HCLK4 = 240 + */ + +#define STM32_RCC_D1CFGR_HPRE RCC_D1CFGR_HPRE_SYSCLKd2 /* HCLK = SYSCLK / 2 */ +#define STM32_ACLK_FREQUENCY (STM32_CPUCLK_FREQUENCY / 2) /* ACLK in D1, HCLK3 in D1 */ +#define STM32_HCLK_FREQUENCY (STM32_CPUCLK_FREQUENCY / 2) /* HCLK in D2, HCLK4 in D3 */ +#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */ + +/* APB1 clock (PCLK1) is HCLK/2 (120 MHz) */ + +#define STM32_RCC_D2CFGR_D2PPRE1 RCC_D2CFGR_D2PPRE1_HCLKd2 /* PCLK1 = HCLK / 2 */ +#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2) + +/* APB2 clock (PCLK2) is HCLK/2 (120 MHz) */ + +#define STM32_RCC_D2CFGR_D2PPRE2 RCC_D2CFGR_D2PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */ +#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2) + +/* APB3 clock (PCLK3) is HCLK/2 (120 MHz) */ + +#define STM32_RCC_D1CFGR_D1PPRE RCC_D1CFGR_D1PPRE_HCLKd2 /* PCLK3 = HCLK / 2 */ +#define STM32_PCLK3_FREQUENCY (STM32_HCLK_FREQUENCY/2) + +/* APB4 clock (PCLK4) is HCLK/4 (120 MHz) */ + +#define STM32_RCC_D3CFGR_D3PPRE RCC_D3CFGR_D3PPRE_HCLKd2 /* PCLK4 = HCLK / 2 */ +#define STM32_PCLK4_FREQUENCY (STM32_HCLK_FREQUENCY/2) + +/* Timer clock frequencies */ + +/* Timers driven from APB1 will be twice PCLK1 */ + +#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY) + +/* Timers driven from APB2 will be twice PCLK2 */ + +#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM15_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM16_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM17_CLKIN (2*STM32_PCLK2_FREQUENCY) + +/* Kernel Clock Configuration + * + * Note: look at Table 54 in ST Manual + */ + +/* I2C123 clock source */ + +#define STM32_RCC_D2CCIP2R_I2C123SRC RCC_D2CCIP2R_I2C123SEL_HSI + +/* I2C4 clock source */ + +#define STM32_RCC_D3CCIPR_I2C4SRC RCC_D3CCIPR_I2C4SEL_HSI + +/* SPI123 clock source */ + +#define STM32_RCC_D2CCIP1R_SPI123SRC RCC_D2CCIP1R_SPI123SEL_PLL2 + +/* SPI45 clock source */ + +#define STM32_RCC_D2CCIP1R_SPI45SRC RCC_D2CCIP1R_SPI45SEL_PLL2 + +/* SPI6 clock source */ + +#define STM32_RCC_D3CCIPR_SPI6SRC RCC_D3CCIPR_SPI6SEL_PLL2 + +/* USB 1 and 2 clock source */ + +#define STM32_RCC_D2CCIP2R_USBSRC RCC_D2CCIP2R_USBSEL_PLL3 + +/* ADC 1 2 3 clock source */ + +#define STM32_RCC_D3CCIPR_ADCSEL RCC_D3CCIPR_ADCSEL_PLL2 + +/* FDCAN 1 clock source */ + +#define STM32_RCC_D2CCIP1R_FDCANSEL RCC_D2CCIP1R_FDCANSEL_HSE /* FDCAN 1 2 clock source */ + +#define STM32_FDCANCLK STM32_HSE_FREQUENCY + +/* FLASH wait states + * + * ------------ ---------- ----------- + * Vcore MAX ACLK WAIT STATES + * ------------ ---------- ----------- + * 1.15-1.26 V 70 MHz 0 + * (VOS1 level) 140 MHz 1 + * 210 MHz 2 + * 1.05-1.15 V 55 MHz 0 + * (VOS2 level) 110 MHz 1 + * 165 MHz 2 + * 220 MHz 3 + * 0.95-1.05 V 45 MHz 0 + * (VOS3 level) 90 MHz 1 + * 135 MHz 2 + * 180 MHz 3 + * 225 MHz 4 + * ------------ ---------- ----------- + */ + +#define BOARD_FLASH_WAITSTATES 2 + +/* SDMMC definitions ********************************************************/ + +/* Init 480kHz, freq = PLL1Q/(2*div) div = PLL1Q/(2*freq) */ + +#define STM32_SDMMC_INIT_CLKDIV (300 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT) + +/* 20 MHz Max for now - more reliable on some boards than 25 MHz + * 20 MHz = PLL1Q/(2*div), div = PLL1Q/(2*freq), div = 6 = 240 / 40 + */ + +#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA) +# define STM32_SDMMC_MMCXFR_CLKDIV (6 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT) +#else +# define STM32_SDMMC_MMCXFR_CLKDIV (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT) +#endif +#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA) +# define STM32_SDMMC_SDXFR_CLKDIV (6 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT) +#else +# define STM32_SDMMC_SDXFR_CLKDIV (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT) +#endif + +#define STM32_SDMMC_CLKCR_EDGE STM32_SDMMC_CLKCR_NEGEDGE + +/* LED definitions ******************************************************************/ +/* The board has two, LED_GREEN a Green LED and LED_BLUE a Blue LED, + * that can be controlled by software. + * + * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way. + * The following definitions are used to access individual LEDs. + */ + +/* LED index values for use with board_userled() */ + +#define BOARD_LED1 0 +#define BOARD_LED2 1 +#define BOARD_LED3 2 +#define BOARD_NLEDS 3 + +#define BOARD_LED_RED BOARD_LED1 +#define BOARD_LED_GREEN BOARD_LED2 +#define BOARD_LED_BLUE BOARD_LED3 + +/* LED bits for use with board_userled_all() */ + +#define BOARD_LED1_BIT (1 << BOARD_LED1) +#define BOARD_LED2_BIT (1 << BOARD_LED2) +#define BOARD_LED3_BIT (1 << BOARD_LED3) + +/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in + * include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related + * events as follows: + * + * + * SYMBOL Meaning LED state + * Red Green Blue + * ---------------------- -------------------------- ------ ------ ----*/ + +#define LED_STARTED 0 /* NuttX has been started OFF OFF OFF */ +#define LED_HEAPALLOCATE 1 /* Heap has been allocated OFF OFF ON */ +#define LED_IRQSENABLED 2 /* Interrupts enabled OFF ON OFF */ +#define LED_STACKCREATED 3 /* Idle stack created OFF ON ON */ +#define LED_INIRQ 4 /* In an interrupt N/C N/C GLOW */ +#define LED_SIGNAL 5 /* In a signal handler N/C GLOW N/C */ +#define LED_ASSERTION 6 /* An assertion failed GLOW N/C GLOW */ +#define LED_PANIC 7 /* The system has crashed Blink OFF N/C */ +#define LED_IDLE 8 /* MCU is is sleep mode ON OFF OFF */ + +/* Thus if the Green LED is statically on, NuttX has successfully booted and + * is, apparently, running normally. If the Red LED is flashing at + * approximately 2Hz, then a fatal error has been detected and the system + * has halted. + */ + +/* Alternate function pin selections ************************************************/ + +#define GPIO_USART1_RX GPIO_USART1_RX_2 /* PA10 */ +#define GPIO_USART1_TX GPIO_USART1_TX_2 /* PA9 */ + +#define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */ +#define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */ + +#define GPIO_USART3_RX GPIO_USART3_RX_3 /* PD9 */ +#define GPIO_USART3_TX GPIO_USART3_TX_3 /* PD8 */ + +#define GPIO_UART4_RX GPIO_UART4_RX_2 /* PA1 */ +#define GPIO_UART4_TX GPIO_UART4_TX_2 /* PA0 */ + +#define GPIO_USART6_RX GPIO_USART6_RX_1 /* PC7 */ +#define GPIO_USART6_TX GPIO_USART6_TX_1 /* PC6 */ + +#define GPIO_UART7_RX GPIO_UART7_RX_3 /* PE7 */ +#define GPIO_UART7_TX GPIO_UART7_TX_3 /* PE8 */ + + +#define GPIO_UART8_RX GPIO_UART8_RX_1 /* PE0 */ +#define GPIO_UART8_TX GPIO_UART8_TX_1 /* PE1 */ + + +/* CAN + * + * CAN1 is routed to transceiver. + */ + +#define GPIO_CAN1_RX GPIO_CAN1_RX_2 /* PB8 */ +#define GPIO_CAN1_TX GPIO_CAN1_TX_2 /* PB9 */ + +/* SPI + * + + */ + +#define ADJ_SLEW_RATE(p) (((p) & ~GPIO_SPEED_MASK) | (GPIO_SPEED_2MHz)) + +#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1 /* PA6 */ +#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1 /* PA7 */ +#define GPIO_SPI1_SCK ADJ_SLEW_RATE(GPIO_SPI1_SCK_1) /* PA5 */ + +#define GPIO_SPI2_MISO GPIO_SPI2_MISO_2 /* PC2 */ +#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_3 /* PC3 */ +#define GPIO_SPI2_SCK ADJ_SLEW_RATE(GPIO_SPI2_SCK_5) /* PD3 */ + + + +/* I2C + * + + * + */ + +#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1 /* PB6 */ +#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1 /* PB7 */ + +#define GPIO_I2C1_SCL_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN6) +#define GPIO_I2C1_SDA_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN7) + +#define GPIO_I2C2_SCL GPIO_I2C2_SCL_1 /* PB10 */ +#define GPIO_I2C2_SDA GPIO_I2C2_SDA_1 /* PB11 */ + +#define GPIO_I2C2_SCL_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN10) +#define GPIO_I2C2_SDA_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN11) + +# define PROBE_INIT(mask) +# define PROBE(n,s) +# define PROBE_MARK(n) + +#endif /*__NUTTX_CONFIG_MICOAIR743_INCLUDE_BOARD_H */ diff --git a/boards/micoair/h743/nuttx-config/include/board_dma_map.h b/boards/micoair/h743/nuttx-config/include/board_dma_map.h new file mode 100644 index 000000000000..ba3f15eb9701 --- /dev/null +++ b/boards/micoair/h743/nuttx-config/include/board_dma_map.h @@ -0,0 +1,36 @@ +/**************************************************************************** + * + * Copyright (c) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#pragma once +#define DMAMAP_SPI2_RX DMAMAP_DMA12_SPI2RX_0 /* DMA1:39 */ +#define DMAMAP_SPI2_TX DMAMAP_DMA12_SPI2TX_0 /* DMA1:40 */ diff --git a/boards/micoair/h743/nuttx-config/nsh/defconfig b/boards/micoair/h743/nuttx-config/nsh/defconfig new file mode 100644 index 000000000000..9e4db72b9044 --- /dev/null +++ b/boards/micoair/h743/nuttx-config/nsh/defconfig @@ -0,0 +1,245 @@ +# +# This file is autogenerated: PLEASE DO NOT EDIT IT. +# +# You can use "make menuconfig" to make any modifications to the installed .config file. +# You can then do "make savedefconfig" to generate a new defconfig file that includes your +# modifications. +# +# CONFIG_DEV_CONSOLE is not set +# CONFIG_DISABLE_ENVIRON is not set +# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set +# CONFIG_DISABLE_PTHREAD is not set +# CONFIG_MMCSD_HAVE_CARDDETECT is not set +# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set +# CONFIG_MMCSD_MMCSUPPORT is not set +# CONFIG_MMCSD_SPI is not set +# CONFIG_NSH_DISABLEBG is not set +# CONFIG_NSH_DISABLESCRIPT is not set +# CONFIG_NSH_DISABLE_CAT is not set +# CONFIG_NSH_DISABLE_CD is not set +# CONFIG_NSH_DISABLE_CP is not set +# CONFIG_NSH_DISABLE_DATE is not set +# CONFIG_NSH_DISABLE_DF is not set +# CONFIG_NSH_DISABLE_ECHO is not set +# CONFIG_NSH_DISABLE_ENV is not set +# CONFIG_NSH_DISABLE_EXEC is not set +# CONFIG_NSH_DISABLE_EXIT is not set +# CONFIG_NSH_DISABLE_EXPORT is not set +# CONFIG_NSH_DISABLE_FREE is not set +# CONFIG_NSH_DISABLE_GET is not set +# CONFIG_NSH_DISABLE_HELP is not set +# CONFIG_NSH_DISABLE_ITEF is not set +# CONFIG_NSH_DISABLE_KILL is not set +# CONFIG_NSH_DISABLE_LOOPS is not set +# CONFIG_NSH_DISABLE_LS is not set +# CONFIG_NSH_DISABLE_MKDIR is not set +# CONFIG_NSH_DISABLE_MKFATFS is not set +# CONFIG_NSH_DISABLE_MOUNT is not set +# CONFIG_NSH_DISABLE_MV is not set +# CONFIG_NSH_DISABLE_PRINTF is not set +# CONFIG_NSH_DISABLE_PS is not set +# CONFIG_NSH_DISABLE_PSSTACKUSAGE is not set +# CONFIG_NSH_DISABLE_PWD is not set +# CONFIG_NSH_DISABLE_RM is not set +# CONFIG_NSH_DISABLE_RMDIR is not set +# CONFIG_NSH_DISABLE_SEMICOLON is not set +# CONFIG_NSH_DISABLE_SET is not set +# CONFIG_NSH_DISABLE_SLEEP is not set +# CONFIG_NSH_DISABLE_SOURCE is not set +# CONFIG_NSH_DISABLE_TEST is not set +# CONFIG_NSH_DISABLE_TIME is not set +# CONFIG_NSH_DISABLE_UMOUNT is not set +# CONFIG_NSH_DISABLE_UNSET is not set +# CONFIG_NSH_DISABLE_USLEEP is not set +CONFIG_ARCH="arm" +CONFIG_ARCH_BOARD_CUSTOM=y +CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/micoair/h743/nuttx-config" +CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y +CONFIG_ARCH_BOARD_CUSTOM_NAME="px4" +CONFIG_ARCH_CHIP="stm32h7" +CONFIG_ARCH_CHIP_STM32H743VI=y +CONFIG_ARCH_CHIP_STM32H7=y +CONFIG_ARCH_INTERRUPTSTACK=768 +CONFIG_ARCH_STACKDUMP=y +CONFIG_ARMV7M_BASEPRI_WAR=y +CONFIG_ARMV7M_DCACHE=y +CONFIG_ARMV7M_DTCM=y +CONFIG_ARMV7M_ICACHE=y +CONFIG_ARMV7M_MEMCPY=y +CONFIG_ARMV7M_USEBASEPRI=y +CONFIG_BOARDCTL_RESET=y +CONFIG_BOARD_ASSERT_RESET_VALUE=0 +CONFIG_BOARD_CRASHDUMP=y +CONFIG_BOARD_LOOPSPERMSEC=95150 +CONFIG_BOARD_RESET_ON_ASSERT=2 +CONFIG_BUILTIN=y +CONFIG_CDCACM=y +CONFIG_CDCACM_PRODUCTID=0x0036 +CONFIG_CDCACM_PRODUCTSTR="MicoAir743" +CONFIG_CDCACM_RXBUFSIZE=600 +CONFIG_CDCACM_TXBUFSIZE=12000 +CONFIG_CDCACM_VENDORID=0x1B8C +CONFIG_CDCACM_VENDORSTR="MicoAir" +CONFIG_DEBUG_FULLOPT=y +CONFIG_DEBUG_HARDFAULT_ALERT=y +CONFIG_DEBUG_MEMFAULT=y +CONFIG_DEBUG_SYMBOLS=y +CONFIG_DEFAULT_SMALL=y +CONFIG_DEV_FIFO_SIZE=0 +CONFIG_DEV_PIPE_MAXSIZE=1024 +CONFIG_DEV_PIPE_SIZE=70 +CONFIG_EXPERIMENTAL=y +CONFIG_FAT_DMAMEMORY=y +CONFIG_FAT_LCNAMES=y +CONFIG_FAT_LFN=y +CONFIG_FAT_LFN_ALIAS_HASH=y +CONFIG_FDCLONE_STDIO=y +CONFIG_FS_BINFS=y +CONFIG_FS_CROMFS=y +CONFIG_FS_FAT=y +CONFIG_FS_FATTIME=y +CONFIG_FS_PROCFS=y +CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y +CONFIG_FS_PROCFS_MAX_TASKS=64 +CONFIG_FS_PROCFS_REGISTER=y +CONFIG_FS_ROMFS=y +CONFIG_GRAN=y +CONFIG_GRAN_INTR=y +CONFIG_HAVE_CXX=y +CONFIG_HAVE_CXXINITIALIZE=y +CONFIG_I2C=y +CONFIG_I2C_RESET=y +CONFIG_IDLETHREAD_STACKSIZE=750 +CONFIG_INIT_ENTRYPOINT="nsh_main" +CONFIG_INIT_STACKSIZE=3194 +CONFIG_IOB_NBUFFERS=24 +CONFIG_IOB_NCHAINS=24 +CONFIG_LIBC_FLOATINGPOINT=y +CONFIG_LIBC_LONG_LONG=y +CONFIG_LIBC_MAX_EXITFUNS=1 +CONFIG_LIBC_STRERROR=y +CONFIG_MEMSET_64BIT=y +CONFIG_MEMSET_OPTSPEED=y +CONFIG_MMCSD=y +CONFIG_MMCSD_SDIO=y +CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE=y +CONFIG_MM_IOB=y +CONFIG_MM_REGIONS=4 +CONFIG_NAME_MAX=40 +CONFIG_NSH_ARCHINIT=y +CONFIG_NSH_ARGCAT=y +CONFIG_NSH_BUILTIN_APPS=y +CONFIG_NSH_CMDPARMS=y +CONFIG_NSH_CROMFSETC=y +CONFIG_NSH_LINELEN=128 +CONFIG_NSH_MAXARGUMENTS=15 +CONFIG_NSH_NESTDEPTH=8 +CONFIG_NSH_QUOTE=y +CONFIG_NSH_ROMFSETC=y +CONFIG_NSH_ROMFSSECTSIZE=128 +CONFIG_NSH_STRERROR=y +CONFIG_NSH_VARS=y +CONFIG_OTG_ID_GPIO_DISABLE=y +CONFIG_PIPES=y +CONFIG_PREALLOC_TIMERS=50 +CONFIG_PRIORITY_INHERITANCE=y +CONFIG_PTHREAD_MUTEX_ROBUST=y +CONFIG_PTHREAD_STACK_MIN=512 +CONFIG_RAM_SIZE=245760 +CONFIG_RAM_START=0x20010000 +CONFIG_RAW_BINARY=y +CONFIG_RTC_DATETIME=y +CONFIG_SCHED_HPWORK=y +CONFIG_SCHED_HPWORKPRIORITY=249 +CONFIG_SCHED_HPWORKSTACKSIZE=1280 +CONFIG_SCHED_INSTRUMENTATION=y +CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y +CONFIG_SCHED_INSTRUMENTATION_SWITCH=y +CONFIG_SCHED_LPWORK=y +CONFIG_SCHED_LPWORKPRIORITY=50 +CONFIG_SCHED_LPWORKSTACKSIZE=1632 +CONFIG_SCHED_WAITPID=y +CONFIG_SDMMC1_SDIO_PULLUP=y +CONFIG_SEM_PREALLOCHOLDERS=32 +CONFIG_SERIAL_TERMIOS=y +CONFIG_SIG_DEFAULT=y +CONFIG_SIG_SIGALRM_ACTION=y +CONFIG_SIG_SIGUSR1_ACTION=y +CONFIG_SIG_SIGUSR2_ACTION=y +CONFIG_SIG_SIGWORK=4 +CONFIG_STACK_COLORATION=y +CONFIG_START_DAY=30 +CONFIG_START_MONTH=11 +CONFIG_STDIO_BUFFER_SIZE=256 +CONFIG_STM32H7_ADC1=y +CONFIG_STM32H7_ADC3=y +CONFIG_STM32H7_BBSRAM=y +CONFIG_STM32H7_BBSRAM_FILES=5 +CONFIG_STM32H7_BDMA=y +CONFIG_STM32H7_BKPSRAM=y +CONFIG_STM32H7_DMA1=y +CONFIG_STM32H7_DMA2=y +CONFIG_STM32H7_DMACAPABLE=y +CONFIG_STM32H7_FLASH_OVERRIDE_I=y +CONFIG_STM32H7_I2C1=y +CONFIG_STM32H7_I2C2=y +CONFIG_STM32H7_I2C_DYNTIMEO=y +CONFIG_STM32H7_I2C_DYNTIMEO_STARTSTOP=10 +CONFIG_STM32H7_OTGFS=y +CONFIG_STM32H7_PROGMEM=y +CONFIG_STM32H7_RTC=y +CONFIG_STM32H7_RTC_HSECLOCK=y +CONFIG_STM32H7_RTC_MAGIC_REG=1 +CONFIG_STM32H7_SAVE_CRASHDUMP=y +CONFIG_STM32H7_SDMMC1=y +CONFIG_STM32H7_SERIALBRK_BSDCOMPAT=y +CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y +CONFIG_STM32H7_SPI1=y +CONFIG_STM32H7_SPI2=y +CONFIG_STM32H7_SPI2_DMA=y +CONFIG_STM32H7_SPI2_DMA_BUFFER=4096 +CONFIG_STM32H7_SPI_DMATHRESHOLD=8 +CONFIG_STM32H7_TIM1=y +CONFIG_STM32H7_TIM3=y +CONFIG_STM32H7_TIM4=y +CONFIG_STM32H7_TIM8=y +CONFIG_STM32H7_UART4=y +CONFIG_STM32H7_UART7=y +CONFIG_STM32H7_UART8=y +CONFIG_STM32H7_USART1=y +CONFIG_STM32H7_USART2=y +CONFIG_STM32H7_USART3=y +CONFIG_STM32H7_USART6=y +CONFIG_STM32H7_USART_BREAKS=y +CONFIG_STM32H7_USART_INVERT=y +CONFIG_STM32H7_USART_SINGLEWIRE=y +CONFIG_STM32H7_USART_SWAP=y +CONFIG_SYSTEM_CDCACM=y +CONFIG_SYSTEM_NSH=y +CONFIG_TASK_NAME_SIZE=24 +CONFIG_UART4_BAUD=57600 +CONFIG_UART4_RXBUFSIZE=600 +CONFIG_UART4_TXBUFSIZE=1500 +CONFIG_UART7_BAUD=57600 +CONFIG_UART7_RXBUFSIZE=600 +CONFIG_UART7_TXBUFSIZE=1500 +CONFIG_UART8_BAUD=57600 +CONFIG_UART8_RXBUFSIZE=600 +CONFIG_UART8_TXBUFSIZE=1500 +CONFIG_USART1_BAUD=57600 +CONFIG_USART1_RXBUFSIZE=600 +CONFIG_USART1_TXBUFSIZE=1500 +CONFIG_USART2_BAUD=57600 +CONFIG_USART2_RXBUFSIZE=600 +CONFIG_USART2_TXBUFSIZE=1500 +CONFIG_USART3_BAUD=57600 +CONFIG_USART3_RXBUFSIZE=600 +CONFIG_USART3_TXBUFSIZE=1500 +CONFIG_USART6_BAUD=57600 +CONFIG_USART6_RXBUFSIZE=600 +CONFIG_USART6_TXBUFSIZE=1500 +CONFIG_USBDEV=y +CONFIG_USBDEV_BUSPOWERED=y +CONFIG_USBDEV_MAXPOWER=500 +CONFIG_USEC_PER_TICK=1000 +CONFIG_WATCHDOG=y diff --git a/boards/micoair/h743/nuttx-config/scripts/bootloader_script.ld b/boards/micoair/h743/nuttx-config/scripts/bootloader_script.ld new file mode 100644 index 000000000000..511ef2624248 --- /dev/null +++ b/boards/micoair/h743/nuttx-config/scripts/bootloader_script.ld @@ -0,0 +1,213 @@ +/**************************************************************************** + * scripts/script.ld + * + * Copyright (C) 2016, 2019 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/* The Durandal-v1 uses an STM32H743II has 2048Kb of main FLASH memory. + * The flash memory is partitioned into a User Flash memory and a System + * Flash memory. Each of these memories has two banks: + * + * 1) User Flash memory: + * + * Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each + * Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each + * + * 2) System Flash memory: + * + * Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector + * Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector + * + * 3) User option bytes for user configuration, only in Bank 1. + * + * In the STM32H743II, two different boot spaces can be selected through + * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and + * BOOT_ADD1 option bytes: + * + * 1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0]. + * ST programmed value: Flash memory at 0x0800:0000 + * 2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0]. + * ST programmed value: System bootloader at 0x1FF0:0000 + * + * The Durandal has a Swtich on board, the BOOT0 pin is at ground so by default, + * the STM32 will boot to address 0x0800:0000 in FLASH unless the swiutch is + * drepresed, then the boot will be from 0x1FF0:0000 + * + * The STM32H743ZI also has 1024Kb of data SRAM. + * SRAM is split up into several blocks and into three power domains: + * + * 1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with + * 0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus + * + * 1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000 + * + * The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit + * DTCM ports. The DTCM-RAM could be used for critical real-time + * data, such as interrupt service routines or stack / heap memory. + * Both DTCM-RAMs can be used in parallel (for load/store operations) + * thanks to the Cortex-M7 dual issue capability. + * + * 1.2) 64Kb of ITCM-RAM beginning at address 0x0000:0000 + * + * This RAM is connected to ITCM 64-bit interface designed for + * execution of critical real-times routines by the CPU. + * + * 2) AXI SRAM (D1 domain) accessible by all system masters except BDMA + * through D1 domain AXI bus matrix + * + * 2.1) 512Kb of SRAM beginning at address 0x2400:0000 + * + * 3) AHB SRAM (D2 domain) accessible by all system masters except BDMA + * through D2 domain AHB bus matrix + * + * 3.1) 128Kb of SRAM1 beginning at address 0x3000:0000 + * 3.2) 128Kb of SRAM2 beginning at address 0x3002:0000 + * 3.3) 32Kb of SRAM3 beginning at address 0x3004:0000 + * + * SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000 + * + * 4) AHB SRAM (D3 domain) accessible by most of system masters + * through D3 domain AHB bus matrix + * + * 4.1) 64Kb of SRAM4 beginning at address 0x3800:0000 + * 4.1) 4Kb of backup RAM beginning at address 0x3880:0000 + * + * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000 + * where the code expects to begin execution by jumping to the entry point in + * the 0x0800:0000 address range. + */ + +MEMORY +{ + itcm (rwx) : ORIGIN = 0x00000000, LENGTH = 64K + flash (rx) : ORIGIN = 0x08000000, LENGTH = 2048K + dtcm1 (rwx) : ORIGIN = 0x20000000, LENGTH = 64K + dtcm2 (rwx) : ORIGIN = 0x20010000, LENGTH = 64K + sram (rwx) : ORIGIN = 0x24000000, LENGTH = 512K + sram1 (rwx) : ORIGIN = 0x30000000, LENGTH = 128K + sram2 (rwx) : ORIGIN = 0x30020000, LENGTH = 128K + sram3 (rwx) : ORIGIN = 0x30040000, LENGTH = 32K + sram4 (rwx) : ORIGIN = 0x38000000, LENGTH = 64K + bbram (rwx) : ORIGIN = 0x38800000, LENGTH = 4K +} + +OUTPUT_ARCH(arm) +EXTERN(_vectors) +ENTRY(_stext) + +/* + * Ensure that abort() is present in the final object. The exception handling + * code pulled in by libgcc.a requires it (and that code cannot be easily avoided). + */ +EXTERN(abort) +EXTERN(_bootdelay_signature) + +SECTIONS +{ + .text : { + _stext = ABSOLUTE(.); + *(.vectors) + . = ALIGN(32); + /* + This signature provides the bootloader with a way to delay booting + */ + _bootdelay_signature = ABSOLUTE(.); + FILL(0xffecc2925d7d05c5) + . += 8; + *(.text .text.*) + *(.fixup) + *(.gnu.warning) + *(.rodata .rodata.*) + *(.gnu.linkonce.t.*) + *(.glue_7) + *(.glue_7t) + *(.got) + *(.gcc_except_table) + *(.gnu.linkonce.r.*) + _etext = ABSOLUTE(.); + + } > flash + + /* + * Init functions (static constructors and the like) + */ + .init_section : { + _sinit = ABSOLUTE(.); + KEEP(*(.init_array .init_array.*)) + _einit = ABSOLUTE(.); + } > flash + + + .ARM.extab : { + *(.ARM.extab*) + } > flash + + __exidx_start = ABSOLUTE(.); + .ARM.exidx : { + *(.ARM.exidx*) + } > flash + __exidx_end = ABSOLUTE(.); + + _eronly = ABSOLUTE(.); + + .data : { + _sdata = ABSOLUTE(.); + *(.data .data.*) + *(.gnu.linkonce.d.*) + CONSTRUCTORS + _edata = ABSOLUTE(.); + } > sram AT > flash + + .bss : { + _sbss = ABSOLUTE(.); + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + . = ALIGN(4); + _ebss = ABSOLUTE(.); + } > sram + + /* Stabs debugging sections. */ + .stab 0 : { *(.stab) } + .stabstr 0 : { *(.stabstr) } + .stab.excl 0 : { *(.stab.excl) } + .stab.exclstr 0 : { *(.stab.exclstr) } + .stab.index 0 : { *(.stab.index) } + .stab.indexstr 0 : { *(.stab.indexstr) } + .comment 0 : { *(.comment) } + .debug_abbrev 0 : { *(.debug_abbrev) } + .debug_info 0 : { *(.debug_info) } + .debug_line 0 : { *(.debug_line) } + .debug_pubnames 0 : { *(.debug_pubnames) } + .debug_aranges 0 : { *(.debug_aranges) } +} diff --git a/boards/micoair/h743/nuttx-config/scripts/script.ld b/boards/micoair/h743/nuttx-config/scripts/script.ld new file mode 100644 index 000000000000..1dc1a0ef97eb --- /dev/null +++ b/boards/micoair/h743/nuttx-config/scripts/script.ld @@ -0,0 +1,228 @@ +/**************************************************************************** + * scripts/script.ld + * + * Copyright (C) 2020 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/* The board uses an STM32H743II and has 2048Kb of main FLASH memory. + * The flash memory is partitioned into a User Flash memory and a System + * Flash memory. Each of these memories has two banks: + * + * 1) User Flash memory: + * + * Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each + * Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each + * + * 2) System Flash memory: + * + * Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector + * Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector + * + * 3) User option bytes for user configuration, only in Bank 1. + * + * In the STM32H743II, two different boot spaces can be selected through + * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and + * BOOT_ADD1 option bytes: + * + * 1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0]. + * ST programmed value: Flash memory at 0x0800:0000 + * 2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0]. + * ST programmed value: System bootloader at 0x1FF0:0000 + * + * There's a switch on board, the BOOT0 pin is at ground so by default, + * the STM32 will boot to address 0x0800:0000 in FLASH unless the switch is + * drepresed, then the boot will be from 0x1FF0:0000 + * + * The STM32H743ZI also has 1024Kb of data SRAM. + * SRAM is split up into several blocks and into three power domains: + * + * 1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with + * 0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus + * + * 1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000 + * + * The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit + * DTCM ports. The DTCM-RAM could be used for critical real-time + * data, such as interrupt service routines or stack / heap memory. + * Both DTCM-RAMs can be used in parallel (for load/store operations) + * thanks to the Cortex-M7 dual issue capability. + * + * 1.2) 64Kb of ITCM-RAM beginning at address 0x0000:0000 + * + * This RAM is connected to ITCM 64-bit interface designed for + * execution of critical real-times routines by the CPU. + * + * 2) AXI SRAM (D1 domain) accessible by all system masters except BDMA + * through D1 domain AXI bus matrix + * + * 2.1) 512Kb of SRAM beginning at address 0x2400:0000 + * + * 3) AHB SRAM (D2 domain) accessible by all system masters except BDMA + * through D2 domain AHB bus matrix + * + * 3.1) 128Kb of SRAM1 beginning at address 0x3000:0000 + * 3.2) 128Kb of SRAM2 beginning at address 0x3002:0000 + * 3.3) 32Kb of SRAM3 beginning at address 0x3004:0000 + * + * SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000 + * + * 4) AHB SRAM (D3 domain) accessible by most of system masters + * through D3 domain AHB bus matrix + * + * 4.1) 64Kb of SRAM4 beginning at address 0x3800:0000 + * 4.1) 4Kb of backup RAM beginning at address 0x3880:0000 + * + * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000 + * where the code expects to begin execution by jumping to the entry point in + * the 0x0800:0000 address range. + */ + +MEMORY +{ + ITCM_RAM (rwx) : ORIGIN = 0x00000000, LENGTH = 64K + FLASH (rx) : ORIGIN = 0x08020000, LENGTH = 1792K + + DTCM1_RAM (rwx) : ORIGIN = 0x20000000, LENGTH = 64K + DTCM2_RAM (rwx) : ORIGIN = 0x20010000, LENGTH = 64K + AXI_SRAM (rwx) : ORIGIN = 0x24000000, LENGTH = 512K /* D1 domain AXI bus */ + SRAM1 (rwx) : ORIGIN = 0x30000000, LENGTH = 128K /* D2 domain AHB bus */ + SRAM2 (rwx) : ORIGIN = 0x30020000, LENGTH = 128K /* D2 domain AHB bus */ + SRAM3 (rwx) : ORIGIN = 0x30040000, LENGTH = 32K /* D2 domain AHB bus */ + SRAM4 (rwx) : ORIGIN = 0x38000000, LENGTH = 64K /* D3 domain */ + BKPRAM (rwx) : ORIGIN = 0x38800000, LENGTH = 4K +} + +OUTPUT_ARCH(arm) +EXTERN(_vectors) +ENTRY(_stext) + +/* + * Ensure that abort() is present in the final object. The exception handling + * code pulled in by libgcc.a requires it (and that code cannot be easily avoided). + */ +EXTERN(abort) +EXTERN(_bootdelay_signature) + +SECTIONS +{ + .text : { + _stext = ABSOLUTE(.); + *(.vectors) + . = ALIGN(32); + /* + This signature provides the bootloader with a way to delay booting + */ + _bootdelay_signature = ABSOLUTE(.); + FILL(0xffecc2925d7d05c5) + . += 8; + *(.text .text.*) + *(.fixup) + *(.gnu.warning) + *(.rodata .rodata.*) + *(.gnu.linkonce.t.*) + *(.glue_7) + *(.glue_7t) + *(.got) + *(.gcc_except_table) + *(.gnu.linkonce.r.*) + _etext = ABSOLUTE(.); + + } > FLASH + + /* + * Init functions (static constructors and the like) + */ + .init_section : { + _sinit = ABSOLUTE(.); + KEEP(*(.init_array .init_array.*)) + _einit = ABSOLUTE(.); + } > FLASH + + + .ARM.extab : { + *(.ARM.extab*) + } > FLASH + + __exidx_start = ABSOLUTE(.); + .ARM.exidx : { + *(.ARM.exidx*) + } > FLASH + __exidx_end = ABSOLUTE(.); + + _eronly = ABSOLUTE(.); + + .data : { + _sdata = ABSOLUTE(.); + *(.data .data.*) + *(.gnu.linkonce.d.*) + CONSTRUCTORS + _edata = ABSOLUTE(.); + + /* Pad out last section as the STM32H7 Flash write size is 256 bits. 32 bytes */ + . = ALIGN(16); + FILL(0xffff) + . += 16; + } > AXI_SRAM AT > FLASH = 0xffff + + .bss : { + _sbss = ABSOLUTE(.); + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + . = ALIGN(4); + _ebss = ABSOLUTE(.); + } > AXI_SRAM + + /* Emit the the D3 power domain section for locating BDMA data */ + + .sram4_reserve (NOLOAD) : + { + *(.sram4) + . = ALIGN(4); + _sram4_heap_start = ABSOLUTE(.); + } > SRAM4 + + /* Stabs debugging sections. */ + .stab 0 : { *(.stab) } + .stabstr 0 : { *(.stabstr) } + .stab.excl 0 : { *(.stab.excl) } + .stab.exclstr 0 : { *(.stab.exclstr) } + .stab.index 0 : { *(.stab.index) } + .stab.indexstr 0 : { *(.stab.indexstr) } + .comment 0 : { *(.comment) } + .debug_abbrev 0 : { *(.debug_abbrev) } + .debug_info 0 : { *(.debug_info) } + .debug_line 0 : { *(.debug_line) } + .debug_pubnames 0 : { *(.debug_pubnames) } + .debug_aranges 0 : { *(.debug_aranges) } +} diff --git a/boards/micoair/h743/src/CMakeLists.txt b/boards/micoair/h743/src/CMakeLists.txt new file mode 100644 index 000000000000..c47215375d08 --- /dev/null +++ b/boards/micoair/h743/src/CMakeLists.txt @@ -0,0 +1,68 @@ +############################################################################ +# +# Copyright (c) 2021 PX4 Development Team. All rights reserved. +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name PX4 nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ +if("${PX4_BOARD_LABEL}" STREQUAL "bootloader") + add_library(drivers_board + bootloader_main.c + usb.c + ) + target_link_libraries(drivers_board + PRIVATE + nuttx_arch + nuttx_drivers + bootloader + ) + target_include_directories(drivers_board PRIVATE ${PX4_SOURCE_DIR}/platforms/nuttx/src/bootloader/common) + +else() + add_library(drivers_board + i2c.cpp + init.c + led.c + sdio.c + spi.cpp + timer_config.cpp + usb.c + ) + add_dependencies(drivers_board arch_board_hw_info) + + target_link_libraries(drivers_board + PRIVATE + arch_io_pins + arch_spi + arch_board_hw_info + drivers__led + nuttx_arch + nuttx_drivers + px4_layer + ) +endif() diff --git a/boards/micoair/h743/src/board_config.h b/boards/micoair/h743/src/board_config.h new file mode 100644 index 000000000000..48ff3ff203ee --- /dev/null +++ b/boards/micoair/h743/src/board_config.h @@ -0,0 +1,197 @@ +/**************************************************************************** + * + * Copyright (c) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file board_config.h + * + * Board internal definitions + */ + +#pragma once + +/**************************************************************************************************** + * Included Files + ****************************************************************************************************/ + +#include +#include +#include + +#include + +/**************************************************************************************************** + * Definitions + ****************************************************************************************************/ + +// #define FLASH_BASED_PARAMS + + +/* LEDs are driven with push open drain to support Anode to 5V or 3.3V */ + +# define GPIO_nLED_RED /* PE5 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN5) +# define GPIO_nLED_GREEN /* PE6 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN6) +# define GPIO_nLED_BLUE /* PE4 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN4) + +# define BOARD_HAS_CONTROL_STATUS_LEDS 1 +# define BOARD_OVERLOAD_LED LED_RED +# define BOARD_ARMED_STATE_LED LED_BLUE + + +/* + * ADC channels + * + * These are the channel numbers of the ADCs of the microcontroller that + * can be used by the Px4 Firmware in the adc driver + */ + +/* ADC defines to be used in sensors.cpp to read from a particular channel */ +#define SYSTEM_ADC_BASE STM32_ADC1_BASE +#define ADC1_CH(n) (n) + +/* Define GPIO pins used as ADC N.B. Channel numbers must match below */ +#define PX4_ADC_GPIO \ + /* PC0 */ GPIO_ADC123_INP10, \ + /* PC1 */ GPIO_ADC123_INP11 + + +/* Define Channel numbers must match above GPIO pin IN(n)*/ +#define ADC_BATTERY_VOLTAGE_CHANNEL /* PC0 */ ADC1_CH(10) +#define ADC_BATTERY_CURRENT_CHANNEL /* PC1 */ ADC1_CH(11) + + +#define ADC_CHANNELS \ + ((1 << ADC_BATTERY_VOLTAGE_CHANNEL) | \ + (1 << ADC_BATTERY_CURRENT_CHANNEL)) + + +/* Define Battery 1 Voltage Divider and A per V + */ + +// #define BOARD_BATTERY1_V_DIV (11.0f) /* measured with the provided PM board */ +// #define BOARD_BATTERY1_A_PER_V (40.0f) +// #define BOARD_BATTERY2_V_DIV (11.0f) /* measured with the provided PM board */ + + +/* PWM + */ +#define DIRECT_PWM_OUTPUT_CHANNELS 10 +#define DIRECT_INPUT_TIMER_CHANNELS 10 + +#define BOARD_HAS_PWM DIRECT_PWM_OUTPUT_CHANNELS + + +/* USB OTG FS + * + * PA8 OTG_FS_VBUS VBUS sensing + */ + +#define GPIO_OTGFS_VBUS /* PA8 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_100MHz|GPIO_PORTA|GPIO_PIN8) + + +/* High-resolution timer */ +#define HRT_TIMER 2 /* use timer8 for the HRT */ +#define HRT_TIMER_CHANNEL 1 /* use capture/compare channel 3 */ + + +/* RC Serial port */ +#define RC_SERIAL_PORT "/dev/ttyS4" +#define BOARD_SUPPORTS_RC_SERIAL_PORT_OUTPUT + +/* SD Card */ +#define SDIO_SLOTNO 0 /* Only one slot */ +#define SDIO_MINOR 0 + +/* This board provides a DMA pool and APIs */ +#define BOARD_DMA_ALLOC_POOL_SIZE 5120 + +/* This board provides the board_on_reset interface */ +#define BOARD_HAS_ON_RESET 1 + +#define PX4_GPIO_INIT_LIST { \ + PX4_ADC_GPIO, \ + GPIO_CAN1_TX, \ + GPIO_CAN1_RX, \ + } + +#define BOARD_ENABLE_CONSOLE_BUFFER + +#define FLASH_BASED_PARAMS + +#define BOARD_NUM_IO_TIMERS 4 + + +__BEGIN_DECLS + +/**************************************************************************************************** + * Public Types + ****************************************************************************************************/ + +/**************************************************************************************************** + * Public data + ****************************************************************************************************/ + +#ifndef __ASSEMBLY__ + +/**************************************************************************************************** + * Public Functions + ****************************************************************************************************/ + +/**************************************************************************** + * Name: stm32_sdio_initialize + * + * Description: + * Initialize SDIO-based MMC/SD card support + * + ****************************************************************************/ + +int stm32_sdio_initialize(void); + +/**************************************************************************************************** + * Name: stm32_spiinitialize + * + * Description: + * Called to configure SPI chip select GPIO pins for the board. + * + ****************************************************************************************************/ + +extern void stm32_spiinitialize(void); + +extern void stm32_usbinitialize(void); + +extern void board_peripheral_reset(int ms); + +#include + +#endif /* __ASSEMBLY__ */ + +__END_DECLS diff --git a/boards/micoair/h743/src/bootloader_main.c b/boards/micoair/h743/src/bootloader_main.c new file mode 100644 index 000000000000..5670308a29d8 --- /dev/null +++ b/boards/micoair/h743/src/bootloader_main.c @@ -0,0 +1,75 @@ +/**************************************************************************** + * + * Copyright (c) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file bootloader_main.c + * + * FMU-specific early startup code for bootloader +*/ + +#include "board_config.h" +#include "bl.h" + +#include +#include +#include +#include +#include +#include "arm_internal.h" +#include + +extern int sercon_main(int c, char **argv); + +__EXPORT void board_on_reset(int status) {} + +__EXPORT void stm32_boardinitialize(void) +{ + /* configure USB interfaces */ + stm32_usbinitialize(); +} + +__EXPORT int board_app_initialize(uintptr_t arg) +{ + return 0; +} + +void board_late_initialize(void) +{ + sercon_main(0, NULL); +} + +extern void sys_tick_handler(void); +void board_timerhook(void) +{ + sys_tick_handler(); +} diff --git a/boards/micoair/h743/src/hw_config.h b/boards/micoair/h743/src/hw_config.h new file mode 100644 index 000000000000..a428dd53592d --- /dev/null +++ b/boards/micoair/h743/src/hw_config.h @@ -0,0 +1,135 @@ +/**************************************************************************** + * + * Copyright (C) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#pragma once + +/**************************************************************************** + * 10-8--2016: + * To simplify the ripple effect on the tools, we will be using + * /dev/serial/by-id/PX4 to locate PX4 devices. Therefore + * moving forward all Bootloaders must contain the prefix "PX4 BL " + * in the USBDEVICESTRING + * This Change will be made in an upcoming BL release + ****************************************************************************/ +/* + * Define usage to configure a bootloader + * + * + * Constant example Usage + * APP_LOAD_ADDRESS 0x08004000 - The address in Linker Script, where the app fw is org-ed + * BOOTLOADER_DELAY 5000 - Ms to wait while under USB pwr or bootloader request + * BOARD_FMUV2 + * INTERFACE_USB 1 - (Optional) Scan and use the USB interface for bootloading + * INTERFACE_USART 1 - (Optional) Scan and use the Serial interface for bootloading + * USBDEVICESTRING "PX4 BL FMU v2.x" - USB id string + * USBPRODUCTID 0x0011 - PID Should match defconfig + * BOOT_DELAY_ADDRESS 0x000001a0 - (Optional) From the linker script from Linker Script to get a custom + * delay provided by an APP FW + * BOARD_TYPE 9 - Must match .prototype boad_id + * _FLASH_KBYTES (*(uint16_t *)0x1fff7a22) - Run time flash size detection + * BOARD_FLASH_SECTORS ((_FLASH_KBYTES == 0x400) ? 11 : 23) - Run time determine the physical last sector + * BOARD_FLASH_SECTORS 11 - Hard coded zero based last sector + * BOARD_FLASH_SIZE (_FLASH_KBYTES*1024)- Total Flash size of device, determined at run time. + * (1024 * 1024) - Hard coded Total Flash of device - The bootloader and app reserved will be deducted + * programmatically + * + * BOARD_FIRST_FLASH_SECTOR_TO_ERASE 2 - Optional sectors index in the flash_sectors table (F4 only), to begin erasing. + * This is to allow sectors to be reserved for app fw usage. That will NOT be erased + * during a FW upgrade. + * The default is 0, and selects the first sector to be erased, as the 0th entry in the + * flash_sectors table. Which is the second physical sector of FLASH in the device. + * The first physical sector of FLASH is used by the bootloader, and is not defined + * in the table. + * + * APP_RESERVATION_SIZE (BOARD_FIRST_FLASH_SECTOR_TO_ERASE * 16 * 1024) - Number of bytes reserved by the APP FW. This number plus + * BOOTLOADER_RESERVATION_SIZE will be deducted from + * BOARD_FLASH_SIZE to determine the size of the App FW + * and hence the address space of FLASH to erase and program. + * USBMFGSTRING "PX4 AP" - Optional USB MFG string (default is '3D Robotics' if not defined.) + * SERIAL_BREAK_DETECT_DISABLED - Optional prevent break selection on Serial port from entering or staying in BL + * + * * Other defines are somewhat self explanatory. + */ + +/* Boot device selection list*/ +#define USB0_DEV 0x01 +#define SERIAL0_DEV 0x02 +#define SERIAL1_DEV 0x04 + +#define APP_LOAD_ADDRESS 0x08020000 +#define BOOTLOADER_DELAY 5000 +#define INTERFACE_USB 1 +#define INTERFACE_USB_CONFIG "/dev/ttyACM0" +#define BOARD_VBUS MK_GPIO_INPUT(GPIO_OTGFS_VBUS) + +//#define USE_VBUS_PULL_DOWN +#define INTERFACE_USART 1 +#define INTERFACE_USART_CONFIG "/dev/ttyS0,115200" +#define BOOT_DELAY_ADDRESS 0x000001a0 +#define BOARD_TYPE 1166 +#define BOARD_FLASH_SECTORS (14) +#define BOARD_FLASH_SIZE (16 * 128 * 1024) +#define APP_RESERVATION_SIZE (1 * 128 * 1024) + +#define OSC_FREQ 8 + +#define BOARD_PIN_LED_ACTIVITY GPIO_nLED_BLUE // BLUE +#define BOARD_PIN_LED_BOOTLOADER GPIO_nLED_GREEN // GREEN +#define BOARD_LED_ON 0 +#define BOARD_LED_OFF 1 + +#define SERIAL_BREAK_DETECT_DISABLED 1 + +#if !defined(ARCH_SN_MAX_LENGTH) +# define ARCH_SN_MAX_LENGTH 12 +#endif + +#if !defined(APP_RESERVATION_SIZE) +# define APP_RESERVATION_SIZE 0 +#endif + +#if !defined(BOARD_FIRST_FLASH_SECTOR_TO_ERASE) +# define BOARD_FIRST_FLASH_SECTOR_TO_ERASE 1 +#endif + +#if !defined(USB_DATA_ALIGN) +# define USB_DATA_ALIGN +#endif + +#ifndef BOOT_DEVICES_SELECTION +# define BOOT_DEVICES_SELECTION USB0_DEV|SERIAL0_DEV|SERIAL1_DEV +#endif + +#ifndef BOOT_DEVICES_FILTER_ONUSB +# define BOOT_DEVICES_FILTER_ONUSB USB0_DEV|SERIAL0_DEV|SERIAL1_DEV +#endif diff --git a/boards/micoair/h743/src/i2c.cpp b/boards/micoair/h743/src/i2c.cpp new file mode 100644 index 000000000000..1444ea117204 --- /dev/null +++ b/boards/micoair/h743/src/i2c.cpp @@ -0,0 +1,39 @@ +/**************************************************************************** + * + * Copyright (C) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include + +constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = { + initI2CBusExternal(1), + initI2CBusInternal(2), +}; diff --git a/boards/micoair/h743/src/init.c b/boards/micoair/h743/src/init.c new file mode 100644 index 000000000000..43f86f902d24 --- /dev/null +++ b/boards/micoair/h743/src/init.c @@ -0,0 +1,203 @@ +/**************************************************************************** + * + * Copyright (c) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file init.c + * + * FMU-specific early startup code. This file implements the + * board_app_initialize() function that is called early by nsh during startup. + * + * Code here is run before the rcS script is invoked; it should start required + * subsystems and perform board-specific initialisation. + */ + +#include "board_config.h" + +#include + +#include +#include +#include +#include +#include +#include "arm_internal.h" + +#include +#include +#include +#include +#include +#include +#include + +# if defined(FLASH_BASED_PARAMS) +# include +#endif + +__BEGIN_DECLS +extern void led_init(void); +extern void led_on(int led); +extern void led_off(int led); +__END_DECLS + +/************************************************************************************ + * Name: board_peripheral_reset + * + * Description: + * + ************************************************************************************/ +__EXPORT void board_peripheral_reset(int ms) +{ + UNUSED(ms); +} + +/************************************************************************************ + * Name: board_on_reset + * + * Description: + * Optionally provided function called on entry to board_system_reset + * It should perform any house keeping prior to the rest. + * + * status - 1 if resetting to boot loader + * 0 if just resetting + * + ************************************************************************************/ +__EXPORT void board_on_reset(int status) +{ + for (int i = 0; i < DIRECT_PWM_OUTPUT_CHANNELS; ++i) { + px4_arch_configgpio(PX4_MAKE_GPIO_INPUT(io_timer_channel_get_as_pwm_input(i))); + } + + if (status >= 0) { + up_mdelay(6); + } +} + +/************************************************************************************ + * Name: stm32_boardinitialize + * + * Description: + * All STM32 architectures must provide the following entry point. This entry point + * is called early in the initialization -- after all memory has been configured + * and mapped but before any devices have been initialized. + * + ************************************************************************************/ +__EXPORT void stm32_boardinitialize(void) +{ + /* Reset PWM first thing */ + board_on_reset(-1); + + /* configure LEDs */ + board_autoled_initialize(); + + /* configure pins */ + const uint32_t gpio[] = PX4_GPIO_INIT_LIST; + px4_gpio_init(gpio, arraySize(gpio)); + + /* configure SPI interfaces */ + stm32_spiinitialize(); + + /* configure USB interfaces */ + stm32_usbinitialize(); + +} + +/**************************************************************************** + * Name: board_app_initialize + * + * Description: + * Perform application specific initialization. This function is never + * called directly from application code, but only indirectly via the + * (non-standard) boardctl() interface using the command BOARDIOC_INIT. + * + * Input Parameters: + * arg - The boardctl() argument is passed to the board_app_initialize() + * implementation without modification. The argument has no + * meaning to NuttX; + * + * Returned Value: + * Zero (OK) is returned on success; a negated errno value is returned on + * any failure to indicate the nature of the failure. + * + ****************************************************************************/ +__EXPORT int board_app_initialize(uintptr_t arg) +{ + /* Need hrt running before using the ADC */ + px4_platform_init(); + + /* configure the DMA allocator */ + if (board_dma_alloc_init() < 0) { + syslog(LOG_ERR, "[boot] DMA alloc FAILED\n"); + } + + /* initial LED state */ + drv_led_start(); + led_off(LED_RED); + led_off(LED_BLUE); + + if (board_hardfault_init(2, true) != 0) { + led_on(LED_BLUE); + } + +#ifdef CONFIG_MMCSD + int ret = stm32_sdio_initialize(); + + if (ret != OK) { + led_on(LED_BLUE); + return ret; + } + +#endif + +// TODO：internal flash store parameters +#if defined(FLASH_BASED_PARAMS) + static sector_descriptor_t params_sector_map[] = { + {15, 128 * 1024, 0x081E0000}, + {0, 0, 0}, + }; + + /* Initialize the flashfs layer to use heap allocated memory */ + int result = parameter_flashfs_init(params_sector_map, NULL, 0); + + if (result != OK) { + syslog(LOG_ERR, "[boot] FAILED to init params in FLASH %d\n", result); + led_on(LED_RED); + } + +#endif + + /* Configure the HW based on the manifest */ + px4_platform_configure(); + + return OK; +} diff --git a/boards/micoair/h743/src/led.c b/boards/micoair/h743/src/led.c new file mode 100644 index 000000000000..d7794392dbb3 --- /dev/null +++ b/boards/micoair/h743/src/led.c @@ -0,0 +1,114 @@ +/**************************************************************************** + * + * Copyright (c) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file led.c + * + * LED backend. + */ + +#include + +#include + +#include "chip.h" +#include "stm32_gpio.h" +#include "board_config.h" + +#include +#include + +/* + * Ideally we'd be able to get these from arm_internal.h, + * but since we want to be able to disable the NuttX use + * of leds for system indication at will and there is no + * separate switch, we need to build independent of the + * CONFIG_ARCH_LEDS configuration switch. + */ +__BEGIN_DECLS +extern void led_init(void); +extern void led_on(int led); +extern void led_off(int led); +extern void led_toggle(int led); +__END_DECLS + +# define xlat(p) (p) +static uint32_t g_ledmap[] = { + GPIO_nLED_GREEN, // Indexed by BOARD_LED_GREEN + GPIO_nLED_BLUE, // Indexed by BOARD_LED_BLUE + GPIO_nLED_RED, // Indexed by BOARD_LED_RED +}; + +__EXPORT void led_init(void) +{ + /* Configure LED GPIOs for output */ + for (size_t l = 0; l < (sizeof(g_ledmap) / sizeof(g_ledmap[0])); l++) { + if (g_ledmap[l] != 0) { + stm32_configgpio(g_ledmap[l]); + } + } +} + +static void phy_set_led(int led, bool state) +{ + /* Drive Low to switch on */ + if (g_ledmap[led] != 0) { + stm32_gpiowrite(g_ledmap[led], !state); + } +} + +static bool phy_get_led(int led) +{ + /* If Low it is on */ + if (g_ledmap[led] != 0) { + return !stm32_gpioread(g_ledmap[led]); + } + + return false; +} + + +__EXPORT void led_on(int led) +{ + phy_set_led(xlat(led), true); +} + +__EXPORT void led_off(int led) +{ + phy_set_led(xlat(led), false); +} + +__EXPORT void led_toggle(int led) +{ + phy_set_led(xlat(led), !phy_get_led(xlat(led))); +} diff --git a/boards/micoair/h743/src/sdio.c b/boards/micoair/h743/src/sdio.c new file mode 100644 index 000000000000..869d757756a0 --- /dev/null +++ b/boards/micoair/h743/src/sdio.c @@ -0,0 +1,177 @@ +/**************************************************************************** + * + * Copyright (C) 2014, 2016 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include +#include + +#include +#include +#include +#include + +#include +#include + +#include "chip.h" +#include "board_config.h" +#include "stm32_gpio.h" +#include "stm32_sdmmc.h" + +#ifdef CONFIG_MMCSD + + +/**************************************************************************** + * Pre-processor Definitions + ****************************************************************************/ + +/* Card detections requires card support and a card detection GPIO */ + +#define HAVE_NCD 1 +#if !defined(GPIO_SDMMC1_NCD) +# undef HAVE_NCD +#endif + +/**************************************************************************** + * Private Data + ****************************************************************************/ + +static FAR struct sdio_dev_s *sdio_dev; +#ifdef HAVE_NCD +static bool g_sd_inserted = 0xff; /* Impossible value */ +#endif + +/**************************************************************************** + * Private Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: stm32_ncd_interrupt + * + * Description: + * Card detect interrupt handler. + * + ****************************************************************************/ + +#ifdef HAVE_NCD +static int stm32_ncd_interrupt(int irq, FAR void *context) +{ + bool present; + + present = !stm32_gpioread(GPIO_SDMMC1_NCD); + + if (sdio_dev && present != g_sd_inserted) { + sdio_mediachange(sdio_dev, present); + g_sd_inserted = present; + } + + return OK; +} +#endif + +/**************************************************************************** + * Public Functions + ****************************************************************************/ + +/**************************************************************************** + * Name: stm32_sdio_initialize + * + * Description: + * Initialize SDIO-based MMC/SD card support + * + ****************************************************************************/ + +int stm32_sdio_initialize(void) +{ + int ret; + +#ifdef HAVE_NCD + /* Card detect */ + + bool cd_status; + + /* Configure the card detect GPIO */ + + stm32_configgpio(GPIO_SDMMC1_NCD); + + /* Register an interrupt handler for the card detect pin */ + + stm32_gpiosetevent(GPIO_SDMMC1_NCD, true, true, true, stm32_ncd_interrupt); +#endif + + /* Mount the SDIO-based MMC/SD block driver */ + /* First, get an instance of the SDIO interface */ + + finfo("Initializing SDIO slot %d\n", SDIO_SLOTNO); + + sdio_dev = sdio_initialize(SDIO_SLOTNO); + + if (!sdio_dev) { + syslog(LOG_ERR, "[boot] Failed to initialize SDIO slot %d\n", SDIO_SLOTNO); + return -ENODEV; + } + + /* Now bind the SDIO interface to the MMC/SD driver */ + + finfo("Bind SDIO to the MMC/SD driver, minor=%d\n", SDIO_MINOR); + + ret = mmcsd_slotinitialize(SDIO_MINOR, sdio_dev); + + if (ret != OK) { + syslog(LOG_ERR, "[boot] Failed to bind SDIO to the MMC/SD driver: %d\n", ret); + return ret; + } + + finfo("Successfully bound SDIO to the MMC/SD driver\n"); + +#ifdef HAVE_NCD + /* Use SD card detect pin to check if a card is g_sd_inserted */ + + cd_status = !stm32_gpioread(GPIO_SDMMC1_NCD); + finfo("Card detect : %d\n", cd_status); + + sdio_mediachange(sdio_dev, cd_status); +#else + /* Assume that the SD card is inserted. What choice do we have? */ + + sdio_mediachange(sdio_dev, true); +#endif + + return OK; +} + +#endif /* CONFIG_MMCSD */ diff --git a/boards/micoair/h743/src/spi.cpp b/boards/micoair/h743/src/spi.cpp new file mode 100644 index 000000000000..81fdd03f282d --- /dev/null +++ b/boards/micoair/h743/src/spi.cpp @@ -0,0 +1,50 @@ +/**************************************************************************** + * + * Copyright (C) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include +#include +#include + + +constexpr px4_spi_bus_t px4_spi_buses[SPI_BUS_MAX_BUS_ITEMS] = { + initSPIBus(SPI::Bus::SPI1, { + initSPIDevice(DRV_OSD_DEVTYPE_ATXXXX, SPI::CS{GPIO::PortB, GPIO::Pin12}), + }), + initSPIBus(SPI::Bus::SPI2, { + initSPIDevice(DRV_GYR_DEVTYPE_BMI088, SPI::CS{GPIO::PortD, GPIO::Pin5}), + initSPIDevice(DRV_ACC_DEVTYPE_BMI088, SPI::CS{GPIO::PortD, GPIO::Pin4}), + initSPIDevice(DRV_IMU_DEVTYPE_BMI270, SPI::CS{GPIO::PortA, GPIO::Pin15}), + }), +}; + +static constexpr bool unused = validateSPIConfig(px4_spi_buses); diff --git a/boards/micoair/h743/src/timer_config.cpp b/boards/micoair/h743/src/timer_config.cpp new file mode 100644 index 000000000000..515a56928cad --- /dev/null +++ b/boards/micoair/h743/src/timer_config.cpp @@ -0,0 +1,56 @@ +/**************************************************************************** + * + * Copyright (C) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include + +constexpr io_timers_t io_timers[MAX_IO_TIMERS] = { + initIOTimer(Timer::Timer1, DMA{DMA::Index1}), + initIOTimer(Timer::Timer3, DMA{DMA::Index1}), + initIOTimer(Timer::Timer4, DMA{DMA::Index1}), +}; + +constexpr timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = { + initIOTimerChannel(io_timers, {Timer::Timer1, Timer::Channel4}, {GPIO::PortE, GPIO::Pin14}), + initIOTimerChannel(io_timers, {Timer::Timer1, Timer::Channel3}, {GPIO::PortE, GPIO::Pin13}), + initIOTimerChannel(io_timers, {Timer::Timer1, Timer::Channel2}, {GPIO::PortE, GPIO::Pin11}), + initIOTimerChannel(io_timers, {Timer::Timer1, Timer::Channel1}, {GPIO::PortE, GPIO::Pin9}), + initIOTimerChannel(io_timers, {Timer::Timer3, Timer::Channel4}, {GPIO::PortB, GPIO::Pin1}), + initIOTimerChannel(io_timers, {Timer::Timer3, Timer::Channel3}, {GPIO::PortB, GPIO::Pin0}), + initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel1}, {GPIO::PortD, GPIO::Pin12}), + initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel2}, {GPIO::PortD, GPIO::Pin13}), + initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel3}, {GPIO::PortD, GPIO::Pin14}), + initIOTimerChannel(io_timers, {Timer::Timer4, Timer::Channel4}, {GPIO::PortD, GPIO::Pin15}), +}; + +constexpr io_timers_channel_mapping_t io_timers_channel_mapping = + initIOTimerChannelMapping(io_timers, timer_io_channels); diff --git a/boards/micoair/h743/src/usb.c b/boards/micoair/h743/src/usb.c new file mode 100644 index 000000000000..9591784866a6 --- /dev/null +++ b/boards/micoair/h743/src/usb.c @@ -0,0 +1,78 @@ +/**************************************************************************** + * + * Copyright (C) 2021 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file usb.c + * + * Board-specific USB functions. + */ + +#include "board_config.h" +#include +#include +#include +#include + +/************************************************************************************ + * Name: stm32_usbinitialize + * + * Description: + * Called to setup USB-related GPIO pins for the board. + * + ************************************************************************************/ + +__EXPORT void stm32_usbinitialize(void) +{ + /* The OTG FS has an internal soft pull-up */ + + /* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */ + +#ifdef CONFIG_STM32H7_OTGFS + stm32_configgpio(GPIO_OTGFS_VBUS); +#endif +} + +/************************************************************************************ + * Name: stm32_usbsuspend + * + * Description: + * Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is + * used. This function is called whenever the USB enters or leaves suspend mode. + * This is an opportunity for the board logic to shutdown clocks, power, etc. + * while the USB is suspended. + * + ************************************************************************************/ +__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume) +{ + uinfo("resume: %d\n", resume); +}