Wireless Troubleshooting Guide
These instructions may help with suspend/resume issues for more devices than just wireless cards, that is just the (unfortunately not uncommon) example used here.
Resetting wireless cards by reloading drivers
If your wireless card works, but after suspending and resuming your computer, the Network-Manager applet just says "Device not ready", then try un-loading and re-loading the driver.
Determining your wireless card driver
First, determine which kernel module corresponds to your wireless card. There are several ways to do this.
The easiest is via the output of
lspci -k in your sys-net VM:
[user@sys-net ~]$ lspci -k 00:00.0 Network controller: Intel Corporation Wireless 8260 (rev 3a) Subsystem: Intel Corporation Device 0130 Kernel driver in use: iwlwifi Kernel modules: iwlwifi
Here we see that the machine in question has an Intel wireless card, being used by the
iwlwifi kernel module.
Checking logs for relevant messages
View the output of
dmesg in sys-net, and check if you see a bunch of wireless related errors. Depending on your hardware, they may look like the following (or not):
iwlwifi 0000:00:00.0: loaded firmware version 16.242414.0 op_mode iwlmvm iwlwifi 0000:00:00.0: Detected Intel(R) Dual Band Wireless AC 8260, REV=0x208 ... IPv6: ADDRCONF(NETDEV_UP): wlp0s0: link is not ready iwlwifi 0000:00:00.0: L1 Enabled - LTR Enabled iwlwifi 0000:00:00.0: L1 Enabled - LTR Enabled iwlwifi 0000:00:00.0: Failed to load firmware chunk! iwlwifi 0000:00:00.0: Could not load the  uCode section iwlwifi 0000:00:00.0: Failed to start INIT ucode: -110 iwlwifi 0000:00:00.0: Failed to run INIT ucode: -110 ... iwlwifi 0000:00:00.0: Direct firmware load for iwlwifi-8000C-18.ucode failed with error -2
Seeing what modules you have loaded
You can check which drivers are currently loaded with
lsmod, and view details about a module with
For example, we list what modules we have loaded:
[user@sys-net ~]$ lsmod Module Size Used by iwlmvm 315392 0 iwlwifi 155648 1 iwlmvm mac80211 708608 1 iwlmvm cfg80211 557056 3 iwlwifi,mac80211,iwlmvm ...
and check one:
[user@sys-net ~]$ modinfo iwlmvm | grep -E '^(description|author|depends):' author: Copyright(c) 2003- 2015 Intel Corporation <firstname.lastname@example.org> description: The new Intel(R) wireless AGN driver for Linux depends: iwlwifi,mac80211,cfg80211
Hey, it's our wireless driver!
Now, check if reloading the module makes wireless work again:
[user@sys-net ~]$ sudo rmmod iwlmvm [user@sys-net ~]$ sudo modprobe iwlmvm
and try reconnecting to a network that is known to work.
If that is successful, see below about having Qubes automatically reload the driver for you. If not, try also reloading some dependent modules, in our example we must also reload iwlwifi:
[user@sys-net ~]$ modinfo iwlwifi | grep -E '^(description|author|depends):' author: Copyright(c) 2003- 2015 Intel Corporation <email@example.com> description: Intel(R) Wireless WiFi driver for Linux depends: cfg80211
[user@sys-net ~]$ sudo rmmod iwlmvm [user@sys-net ~]$ sudo rmmod iwlwifi [user@sys-net ~]$ sudo modprobe iwlwifi # note the reverse order of loading/unloading [user@sys-net ~]$ sudo modprobe iwlmvm
Automatically reloading drivers on suspend/resume
If reloading the driver (which resets the hardware into a known-state) resolves your issue when done manually, you can have Qubes automatically un/reload them on suspend & resume by listing the relevant modules in
In the above example, it would look like this:
[user@sys-net config]$ cat /rw/config/suspend-module-blacklist # You can list here modules you want to be unloaded before going to sleep. This # file is used only if the VM has any PCI device assigned. Modules will be # automatically loaded after resume. iwlmvm iwlwifi