Skip to content
Permalink
Branch: master
Find file Copy path
Find file Copy path
Fetching contributors…
Cannot retrieve contributors at this time
344 lines (264 sloc) 11.8 KB
name category bzurl oldwikiname prodimagename surveyurl sku tags
Gear Stepper Motor Driver Pack
Sensor
105990072

The Gear Stepper Motor Driver Pack includes a stepper motor and a motor drive board. It's a four-phase eight-stepping stepper motor, and you can easily control this stepper motor via the drive board.

You can use this pack for position control.

Features

  • Low noise
  • Large torque
  • Built-in gearbox

Specification

Item Value
Operating Voltage 5V
Phase 4
Reduction ratio 1/64
Step Angle 5.625°/64
Diameter 28mm / Nema 11
Idle In-traction Frequency >500HZ
Idle Out-traction Frequency >1000HZ
Resistance 21±7%
Noise ≤40dB
Drive mode four-phase eight-stepping

Typical applications

  • Desktop printers
  • Plotters
  • 3d printers
  • CNC milling machines

Hardware Overview

Pin Out

Mechanical drawing

you can click it to see the original picture.

Platforms Supported

Arduino Raspberry Pi BeagleBone Wio LinkIt ONE

!!!Caution The platforms mentioned above as supported is/are an indication of the module's software or theoritical compatibility. We only provide software library or code examples for Arduino platform in most cases. It is not possible to provide software library / demo code for all possible MCU platforms. Hence, users have to write their own software library.

Getting Started

Play With Arduino

Hardware

Materials required

Seeeduino V4.2 Gear Stepper Motor Driver Pack Female-Male jumpers
enter image description here enter image description here enter image description here
Get One Now Get One Now Get One Now

!!!note 1 Please plug the USB cable gently, otherwise you may damage the port. Please use the USB cable with 4 wires inside, the 2 wires cable can't transfer data. If you are not sure about the wire you have, you can click here to buy

**2** To make the Gear-Stepper-Motor-Driver-Pack work with your Arduino, several Female-Male jumpers is also required. In case you do not have jumpers, you can click [here](https://www.seeedstudio.com/1-Pin-Female-Male-Jumper-Wire-125mm-50pcs-pac-p-1319.html) to buy.
  • Step 1. Connect the Gear Stepper Motor Driver Board to your seeedunio via jumppers.
Seeeduino Gear Stepper Motor Driver Board
Digital Pin 8 IN1
Digital Pin 9 IN2
Digital Pin 10 IN3
Digital Pin 11 IN4
GND GND
VCC_5V VCC
VCC_5V VM

!!!Tip You can connect the VM pin to VCC_5V or you can just do not use it as long as you choose the VCC in the switch.

  • Step 2. Plug the stepper motor into the Gear Stepper Motor Driver Board.

  • Step 3. Connect Seeeduino to PC via a USB cable.

Software

!!!Attention If this is the first time you work with Arduino, we strongly recommend you to see Getting Started with Arduino before the start.

  • Step 1. Click the icon in upper right corner of the code block to copy the following code into a new sketch in the Arduino IDE.
int pwm1=9;
int pwm2=10;
int ctr_a =9;
int ctr_b =8;
int ctr_c =11;
int ctr_d =10;
int sd =6;
int i=0;
int t=1500;

void setup()
{
    //pinMode(sd,OUTPUT);
    //pinMode(pwm1,OUTPUT);
    //pinMode(pwm2,OUTPUT);
    pinMode(ctr_a,OUTPUT);
    pinMode(ctr_b,OUTPUT);
    pinMode(ctr_c,OUTPUT);
    pinMode(ctr_d,OUTPUT); 
    delay(1);
    //digitalWrite(sd,HIGH);
    //digitalWrite(pwm1,HIGH);
    //digitalWrite(pwm2,HIGH);
//    digitalWrite(ctr_a,LOW);
//    digitalWrite(ctr_b,LOW);
//    digitalWrite(ctr_c,LOW);
//    digitalWrite(ctr_d,LOW);
        
}


void loop ()
{
//   for(i=1500;i>=1;i--)
//   {
//       digitalWrite(ctr_a,HIGH);//A
//       digitalWrite(ctr_b,LOW);
//       digitalWrite(ctr_c,LOW);
//       digitalWrite(ctr_d,LOW);
//       delay(t);
//       digitalWrite(ctr_a,HIGH);
//       digitalWrite(ctr_b,HIGH);//AB
//       digitalWrite(ctr_c,LOW);
//       digitalWrite(ctr_d,LOW);
//       delay(t);
//       digitalWrite(ctr_a,LOW);
//       digitalWrite(ctr_b,HIGH);//B
//       digitalWrite(ctr_c,LOW);
//       digitalWrite(ctr_d,LOW);
//       delay(t);
//       digitalWrite(ctr_a,LOW);
//       digitalWrite(ctr_b,HIGH);
//       digitalWrite(ctr_c,HIGH);//BC
//        digitalWrite(ctr_d,LOW);
//       delay(t);
//       digitalWrite(ctr_a,LOW);
//       digitalWrite(ctr_b,LOW);
//       digitalWrite(ctr_c,HIGH);//C
//       digitalWrite(ctr_d,LOW);
//       delay(t);
//       digitalWrite(ctr_a,LOW);
//       digitalWrite(ctr_b,LOW);
//       digitalWrite(ctr_c,HIGH);//CD
//       digitalWrite(ctr_d,HIGH);
//       delay(t);
//        digitalWrite(ctr_a,LOW);
//       digitalWrite(ctr_b,LOW);
//       digitalWrite(ctr_c,LOW);//D
//       digitalWrite(ctr_d,HIGH);
//       delay(t);
//        digitalWrite(ctr_a,HIGH);
//       digitalWrite(ctr_b,LOW);
//       digitalWrite(ctr_c,LOW);//DA
//       digitalWrite(ctr_d,HIGH);
//       delay(t);
//       
//   }
//       digitalWrite(ctr_a,LOW);
//       digitalWrite(ctr_b,LOW);
//       digitalWrite(ctr_c,LOW);
//       digitalWrite(ctr_d,LOW);
//   
//   
//   
//     for(i=1500;i>=1;i--)
//   {
//     
//       digitalWrite(ctr_d,HIGH);//D
//       delay(t);
//       digitalWrite(ctr_c,HIGH);//DC
//       delay(t);
//       digitalWrite(ctr_d,LOW);//C
//       delay(t);
//       digitalWrite(ctr_b,HIGH);//CB
//       delay(t);
//       digitalWrite(ctr_c,LOW);//B
//       delay(t);
//       digitalWrite(ctr_a,HIGH);//BA
//       delay(t);
//       digitalWrite(ctr_b,LOW);//A
//       delay(t);
//       digitalWrite(ctr_d,HIGH);//AD
//       delay(t);
//       digitalWrite(ctr_a,LOW);
//       digitalWrite(ctr_d,LOW);
//   }
   
   for(i=1500;i>=1;i--)
   {
       digitalWrite(ctr_a,LOW);//A
       digitalWrite(ctr_b,HIGH);
       digitalWrite(ctr_c,HIGH);
       digitalWrite(ctr_d,HIGH);
       delayMicroseconds(t);
       digitalWrite(ctr_a,LOW);
       digitalWrite(ctr_b,LOW);//AB
       digitalWrite(ctr_c,HIGH);
       digitalWrite(ctr_d,HIGH);
       delayMicroseconds(t);
       digitalWrite(ctr_a,HIGH);
       digitalWrite(ctr_b,LOW);//B
       digitalWrite(ctr_c,HIGH);
       digitalWrite(ctr_d,HIGH);
       delayMicroseconds(t);
       digitalWrite(ctr_a,HIGH);
       digitalWrite(ctr_b,LOW);
       digitalWrite(ctr_c,LOW);//BC
        digitalWrite(ctr_d,HIGH);
       delayMicroseconds(t);
       digitalWrite(ctr_a,HIGH);
       digitalWrite(ctr_b,HIGH);
       digitalWrite(ctr_c,LOW);//C
       digitalWrite(ctr_d,HIGH);
       delayMicroseconds(t);
       digitalWrite(ctr_a,HIGH);
       digitalWrite(ctr_b,HIGH);
       digitalWrite(ctr_c,LOW);//CD
       digitalWrite(ctr_d,LOW);
       delayMicroseconds(t);
        digitalWrite(ctr_a,HIGH);
       digitalWrite(ctr_b,HIGH);
       digitalWrite(ctr_c,HIGH);//D
       digitalWrite(ctr_d,LOW);
       delayMicroseconds(t);
       digitalWrite(ctr_a,LOW);
       digitalWrite(ctr_b,HIGH);
       digitalWrite(ctr_c,HIGH);//DA
       digitalWrite(ctr_d,LOW);
       delayMicroseconds(t);
       
   }
//       digitalWrite(ctr_a,HIGH);
//       digitalWrite(ctr_b,HIGH);
//       digitalWrite(ctr_c,HIGH);
//       digitalWrite(ctr_d,HIGH);
//   
   
   
//     for(i=1500;i>=1;i--)
//   {
//     
//       digitalWrite(ctr_d,HIGH);//D
//       delay(t);
//       digitalWrite(ctr_c,HIGH);//DC
//       delay(t);
//       digitalWrite(ctr_d,LOW);//C
//       delay(t);
//       digitalWrite(ctr_b,HIGH);//CB
//       delay(t);
//       digitalWrite(ctr_c,LOW);//B
//       delay(t);
//       digitalWrite(ctr_a,HIGH);//BA
//       delay(t);
//       digitalWrite(ctr_b,LOW);//A
//       delay(t);
//       digitalWrite(ctr_d,HIGH);//AD
//       delay(t);
//       digitalWrite(ctr_a,LOW);
//       digitalWrite(ctr_d,LOW);
//   }
   

}
  • Step 2. Upload the demo. If you do not know how to upload the code, please check How to upload code.

!!!success If every thing goes well, you can see the motor run:

Resources

Tech Support

Please do not hesitate to submit the issue into our forum

You can’t perform that action at this time.