Permalink
Browse files

blue: blobs for prima wlan 3.1.7.16

  • Loading branch information...
1 parent 1a81348 commit 05f3dcb93c032a9f41d3660249ab1813f85d7dad @codeworkx codeworkx committed Dec 27, 2012
@@ -8,16 +8,13 @@ gEnableImps=1
gEnableIdleScan=0
# Increase sleep duration (seconds) during IMPS
-# 0 implies no periodic wake up from IMPS. Periodic wakeup is
+# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0
# Enable BMPS or not
gEnableBmps=1
-# Enable Close Loop or not
-gEnableCloseLoop=1
-
# Enable suspend or not
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
gEnableSuspend=3
@@ -44,8 +41,8 @@ InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0
-# Enable Firmware RSSI monitoring for roaming
-gEnableFWRssiMonitoring=1
+# Disable RSSI FW filtering
+gEnableFWRssiMonitoring=0
# Make 1x1 the default antenna configuration
gNumRxAnt=1
@@ -56,28 +53,25 @@ gNthBeaconFilter=50
# Enable WAPI or not
# WAPIIsEnabled=0
-# Flags to filter Mcast and Bcast RX packets.
+# Flags to filter Mcast abd Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
-# 2: Filter all Broadcast. 3: Filter all Mcast and Bcast
+# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=3
#Flag to enable HostARPOffload feature or not
hostArpOffload=0
#SoftAP Related Parameters
-# AP MAc addr (obsolete)
+# AP MAc addr
gAPMacAddr=000AF58989EF
-# Enable Random BSSID
-gEnableApRandomBssid=1
-
# 802.11n Protection flag
gEnableApProt=1
-# Enable OBSS protection
+#Enable OBSS protection
gEnableApOBSSProt=0
-# Enable/Disable UAPSD for SoftAP
+#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1
# Fixed Rate
@@ -103,31 +97,18 @@ g11dSupportEnabled=1
# CCX Support and fast transition
CcxEnabled=0
-FastTransitionEnabled=1
+FastTransitionEnabled=0
ImplicitQosIsEnabled=1
gNeighborScanTimerPeriod=200
-gNeighborLookupThreshold=76
-gNeighborReassocThreshold=81
+gNeighborLookupThreshold=50
+gNeighborReassocThreshold=55
+gNeighborScanChannelList=1,11,36,64
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
gMaxNeighborReqTries=3
-# Legacy (non-CCX, non-802.11r) Fast Roaming Support
-# To enable, set FastRoamEnabled=1, gEnableFWRssiMonitoring=1, FastTransitionEnabled=1
-# To disable, set FastRoamEnabled=0, gEnableFWRssiMonitoring=0, FastTransitionEnabled=0
-FastRoamEnabled=1
-
-#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
-#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
-#the RSSI of the new/roamable AP should be for roaming
-RoamRssiDiff=3
-
-#Configure the RSSI gap that will be used to partition/categorize width of
-#each individual category (aka bucket).
-gRssiCatGap=5
-
# SAP Country code
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
# Example
@@ -168,23 +149,20 @@ gApAutoChannelSelection=0
#
gEnablePhyAgcListenMode=128
+#Preferred channel to start BT AMP AP mode (0 means, any channel)
+BtAmpPreferredChannel=0
+
#Preferred band (both or 2.4 only or 5 only)
BandCapability=0
-#Forced Device Listen Interval in multiples of DTIM Period aligned to DTIM
-gEnableModulatedDTIM=3
-
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
-enableBeaconEarlyTermination=1
-beaconEarlyTerminationWakeInterval=11
+enableBeaconEarlyTermination=0
+beaconEarlyTerminationWakeInterval=3
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
gEnableBtAmp=0
-#Preferred channel to start BT AMP AP mode (0 means, any channel)
-BtAmpPreferredChannel=0
-
-#SOFTAP Channel Range selection
+#SOFTAP Channel Range selection
gAPChannelSelectStartChannel=1
gAPChannelSelectEndChannel=11
@@ -193,29 +171,19 @@ gAPChannelSelectEndChannel=11
gAPChannelSelectOperatingBand=0
#Enable Keep alive with non-zero period value
-gStaKeepAlivePeriod = 25
+#gStaKeepAlivePeriod = 30
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
gEnableBypass11d=1
#If set to 0, will not scan DFS channels
-gEnableDFSChnlScan=0
+gEnableDFSChnlScan=1
# Enable logp/SSR
gEnableLogp=1
-# Disable HT40
-gChannelBondingMode5GHz=0
-
# Enable Automatic Tx Power control
gEnableAutomaticTxPowerControl=1
-
-# Derive P2P MAC address from primary MAC address
-isP2pDeviceAddrAdministrated=1
-
-# Disable channel 165 for Indonesia
-gIgnore_Chan165=1
-
END
# Note: Configuration parser would not read anything past the END marker

0 comments on commit 05f3dcb

Please sign in to comment.