You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
That's what I'm hoping to achieve. However as the README has mentioned there are still some issues that can't be overlooked, even if you could get all the exact components right by transferring them from a working board. In specific, the issues are:
the chip U11 and its related traces
the footprint for the resistor networks R5, R6 and R7
Other than these, if you source new components, the capacitors and inductor values and led models are a problem too.
That's what I'm hoping to achieve. However as the README has mentioned there are still some issues that can't be overlooked, even if you could get all the exact components right by transferring them from a working board. In specific, the issues are:
the chip U11 and its related traces
the footprint for the resistor networks R5, R6 and R7
Other than these, if you source new components, the capacitors and inductor values and led models are a problem too.
to get the stock firmware upload file of midi fighter 3d via icsp pinout?
i have request them like this:
Hi,
I have set fuses wrong of midi fighter 64 via icsp port
I use avrduress and forgot to set fuses to 00 so can't detect again the atmega32u4
Should i buy new atmega32u4 chip and flash new bootloader and firmware?
I need your guide and bootloader & firmware & fuses bit value setting
to repair it
and they sent firmware file and tutorial upload by:
Setup
Instal WinAVR (avrdude)
Instal Drivers for the USBTiny Pocket Programmer
Set slide switch on the USB Pocket Programmer to "No Power"
Open Command Prompt, type "avrdude". You should see the version and the options listed
Uploading HEX
Connect the MF64_V3 PCB to the PC with a USB cable
Connect the USB Pocket Programmer as shown in the picture
Make sure all the programing pins are in contact with the PCB. You can put a little pressure on the programmer cable with your thumb to ensure a good connection.
Double click "AVRDude - Upload HEX.bat"
HEX will upload, LED's will cycle RED, GREEN, BLUE. All LED's should be lit, on all colors.
Remove the 6 pin programming header
Remove the MF64_V3 PCB USB connection
Possible Errors:
If USBTiny cannot be found when uploading HEX, unplug and replug the USBTiny Pocket Programmer
maybe you can help to request they sent stock file :))
usb tiny they use it's:
If you have midifighter utility installed, I think you can find the mf3d firmware binary in the internal files.
I have previously sent a support ticket asking for mf3d firmware source code, they replied they did not have plans to release the source code at the time though.
If you have midifighter utility installed, I think you can find the mf3d firmware binary in the internal files.
I have previously sent a support ticket asking for mf3d firmware source code, they replied they did not have plans to release the source code at the time though.
No the factory files is difference they use to set fuses,...
Just ask they new reuqest like me to get the bootloader and fw files because factory they have them, do you use discord telegram or any platform i wanna contact you
That's what I'm hoping to achieve. However as the README has mentioned there are still some issues that can't be overlooked, even if you could get all the exact components right by transferring them from a working board. In specific, the issues are:
the chip U11 and its related traces
the footprint for the resistor networks R5, R6 and R7
Other than these, if you source new components, the capacitors and inductor values and led models are a problem too.
Activity
Zokhoi commentedon Mar 27, 2023
That's what I'm hoping to achieve. However as the README has mentioned there are still some issues that can't be overlooked, even if you could get all the exact components right by transferring them from a working board. In specific, the issues are:
Other than these, if you source new components, the capacitors and inductor values and led models are a problem too.
DRCRecoveryData commentedon Apr 5, 2024
Can you open request to djtechtools:
support@djtechtools.com
to get the stock firmware upload file of midi fighter 3d via icsp pinout?
i have request them like this:
Hi,
I have set fuses wrong of midi fighter 64 via icsp port
I use avrduress and forgot to set fuses to 00 so can't detect again the atmega32u4
Should i buy new atmega32u4 chip and flash new bootloader and firmware?
I need your guide and bootloader & firmware & fuses bit value setting
to repair it
and they sent firmware file and tutorial upload by:
Setup
Uploading HEX
Possible Errors:
maybe you can help to request they sent stock file :))
usb tiny they use it's:
Zokhoi commentedon Apr 5, 2024
If you have midifighter utility installed, I think you can find the mf3d firmware binary in the internal files.
I have previously sent a support ticket asking for mf3d firmware source code, they replied they did not have plans to release the source code at the time though.
DRCRecoveryData commentedon Apr 5, 2024
No the factory files is difference they use to set fuses,...
Just ask they new reuqest like me to get the bootloader and fw files because factory they have them, do you use discord telegram or any platform i wanna contact you
Zokhoi commentedon Apr 5, 2024
My discord is same as my username.
DRCRecoveryData commentedon Apr 5, 2024
can you sent you discord link?
DRCRecoveryData commentedon Apr 9, 2024
U11 is IST8308