Commits on Jan 26, 2013
  1. Some progress

    committed Jan 26, 2013
Commits on Jan 25, 2013
  1. Read materials from OBJ files and store them in the TriangleMesh obje…

    …ct. Now we need to use them...
    committed Jan 25, 2013
Commits on Jan 23, 2013
Commits on Jan 18, 2013
  1. limit layer requests to object->layer_count when preparing skirt #901

    Each object on the plater was being queried for points for
    producing the skirt for all skirt layers, even when the object was
    shorter than the skirt.
    
    layers of the print
    Mike Sheldrake committed Jan 18, 2013
Commits on Jan 17, 2013
  1. Bump version number

    committed Jan 17, 2013
  2. Releasing 0.9.8

    committed Jan 17, 2013
  3. Fixed regression introduced in 4d8757b causing crash during support m…

    …aterial generation
    committed Jan 17, 2013
  4. Update retraction.t to work with two-phase retractions (triggered by …

    …changing the default retract_length_toolchange to something greater than 3)
    committed Jan 17, 2013
  5. Interface support layers were clipped badly. Also, reduce simplificat…

    …ion of the clipping boundaries. #583
    committed Jan 17, 2013
  6. Require Math::Clipper 1.17

    committed Jan 17, 2013
  7. Enable cooling by default

    committed Jan 17, 2013
Commits on Jan 16, 2013
  1. per-thread clipper object for parallel support generation #888

    Mike Sheldrake committed Jan 16, 2013
  2. Merge branch '834-every-n-fill-frags' #834

    Mike Sheldrake committed Jan 16, 2013
  3. use infill flow spacing, not perimeter, for combine_infill() clip off…

    …sets
    Mike Sheldrake committed Jan 15, 2013
Commits on Jan 15, 2013
  1. Ignore perimeter_acceleration and infill_acceleration if their values…

    … are 25 and 50 to handle legacy configs gracefully.
    committed Jan 15, 2013
  2. extraneous fill against sloped walls with fill every N layers #834

    Polygons used for N x depth fill surfaces need to be offset
    by flow spacing before they are reused to clip lower fill surfaces.
    Otherwise thin fill sections remain on clipped layers against sloping
    walls, and the N x depth fill collides with them.
    Mike Sheldrake committed Jan 14, 2013
Commits on Jan 13, 2013
  1. offset miter limit to 3 - 801 828 836 851 875 - spikes and pimples

    Was set to 10 to address 801. Setting to 3 has the same effect for 801,
    and avoids spike artifacts that are likely causing "spike and pimple"
    problems in the referenced issues.
    Mike Sheldrake committed Jan 13, 2013
  2. Bugfix: crash when reading/writing files to paths containing non-ASCI…

    …I characters on Windows. #651 #865
    committed Jan 13, 2013
Commits on Jan 11, 2013
  1. 842, 847 slightly enlarge a clip polygon to counteract integer trunca…

    …tion
    
    Geomery in referenced issues triggered Clipper problems, but also
    pointed to a situation where integer truncation (as coordinates pass
    into Clipper) might be shrinking a clip polygon in a way that leaves
    degenerate or unwanted thin clip results. Growing the clip polygon by 2
    is expected to overcome any issues caused by truncation of floats.
    Mike Sheldrake committed Jan 11, 2013
Commits on Jan 10, 2013
  1. Remove leftover M501

    committed Jan 10, 2013
  2. Acceleration control. #185

    committed Jan 10, 2013
Commits on Jan 2, 2013
Commits on Jan 1, 2013
  1. New unit test for layer heights

    committed Jan 1, 2013
Commits on Dec 31, 2012