solutions: reference designs: Added AD-MAX32LRWISE-SL page and sub-page

.github/styles/config/vocabularies/Base/accept.txt

@@ -65,6 +65,7 @@ Zener
 ns
 dBm
 Gbps
+kbps
 
 [Oo]vercurrent
 [Oo]vervoltage

docs/solutions/reference-designs/ad-max32lrwise-sl/ev-cattletag-ardz/index.rst

@@ -0,0 +1,211 @@
+.. _ev-cattletag-ardz:
+
+EV-CATTLETAG-ARDZ
+=================
+
+Sensor for Livestock Tracking and Health Monitoring
+"""""""""""""""""""""""""""""""""""""""""""""""""""
+
+Overview
+--------
+
+The :adi:`EV-CATTLETAG-ARDZ` is an Arduino board with a fully integrated solution
+for harvesting energy from single-/multicell solar sources. The device includes
+battery chargers for small lithium-ion systems, and a digital temperature sensor
+for applications such as Wearables and IoT. The system is consisting of a
+:adi:`MAX20361` power harvester, :adi:`MAX20335 BMS <MAX20335>`, and a :adi:`MAX30210`
+temperature sensor and a buzzer with an option for vibration motor.
+
+.. figure:: ev-cattletag-ardz.jpg
+   :width: 500 px
+
+Features
+~~~~~~~~
+
+- Monitors the health and vitality of livestock in real-time, enabling farmers
+  to quickly treat animals and prevent the spread of illness or disease.
+- Tracks grazing animals to prevent loss and to identify grazing patterns.
+- Gathers and analyzes historical data to identify trends in cattle health or to
+  track the spread of illness.
+- Monitors readiness to mate or give birth, preventing the loss of new calves
+  and optimizing breeding practices.
+
+Applications
+~~~~~~~~~~~~
+
+- Asset location
+- Asset recovery
+- Asset traceability
+- Inventory management
+- Asset loss and theft prevention
+
+System Architecture
+-------------------
+
+.. figure:: ev-cattletag-ardz_block_diagram.png
+
+Hardware Design
+---------------
+
+Components and Connections
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Power Supply
+^^^^^^^^^^^^
+
+When using the board, the power supply may come from different sources,
+and these are listed below:
+
+.. figure:: ev-cattletag-ardz_power_supply_input.png
+
+- **Solar Panel** - use to recharge the lithium-ion connected to either P8 or to the
+  2x AAA battery. An example of a probe that can be used is a product from
+  AnySolar and its datasheet can be found
+  `here <https://waf-e.dubudisk.com/anysolar.dubuplus.com/techsupport@anysolar.biz/O18Ae08/DubuDisk/www/Gen3/KXOB25-14X1F%20DATA%20SHEET%20202007.pdf>`__.
+- **P6 Terminal block** - external power source (e.g., solar panel)
+
+.. note:: When using an external power source, it is required to
+      disconnect the on-board solar panel by removing the resistor **R30**.
+
+.. figure:: ev-cattletag-ardz_solar_panel_option.png
+
+- **P8 Terminal block** - external power supply, between 3V to 4.2V allowable
+  input
+- **Battery holder** - 2xAAA battery is required.
+- **Arduino Power** - external power supply that comes directly from the host board
+  it is connected to.
+
+.. note:: When power supply directly from the host board is used, it is
+      required to remove the **R84** resistor and placed a 0Ω resistor at **R86**.
+
+.. figure:: ev-cattletag-ardz_power_source_option.png
+
+Digital Interface (Arduino)
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The Arduino interface is a standardized digital interface for various digital
+communication protocols such as SPI, I2C, and UART. These interface types were
+standardized by Arduino, which is hardware and software company. Complete
+details on the PMOD specification can be found
+`here <https://www.arduino.cc/en/hardware>`__.
+
+The pin map for the Arduino pins is described in the table and its schematic
+diagram below.
+
+.. figure:: ev-cattletag-ardz_arduino_connector.png
+
+Applications
+------------
+
+The :adi:`EV-CATTLETAG-ARDZ` can be used with the :adi:`MAX32670-LR-ARDZ` Base Board,
+which is a long-range wireless radio development platform based on MAX32670
+ultralow power Arm Cortex-M4 microcontroller and LR1110 RF transceiver.
+
+Using these platforms together enables users to design solutions based on
+low-power, long range proprietary radio communication technique that is
+suitable for customized heat/flow meters.
+
+To learn more about the Long Range Wireless Radio solution developed by Analog
+Devices, visit the
+:ref:`AD-MAX32LRWISE-SL Long Range Wireless Radio Development Kit User Guide <ad-max32lrwise-sl>`.
+
+System Setup
+------------
+
+PHASE 1: Hardware Setup
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Note that this setup only applies for MAX32670-LR-ARDZ Base Board. Users may use
+a different base board or microcontroller, however the firmware built for this
+demo application cannot be used as this is specifically designed for the
+MAX32670-LR-ARDZ.
+
+Equipment Needed
+^^^^^^^^^^^^^^^^
+
+- One (1) :adi:`MAX32670-LR-ARDZ` Base Board
+- One (1) :adi:`EV-CATTLETAG-ARDZ` Sensor Node
+- One (1) MAX32625PICO Rapid Development Platform with 10-pin ribbon cable
+  with firmware image:
+  `MAX32625PICO Firmware Image for MAX32670 <https://github.com/analogdevicesinc/max32625pico-firmware-images/raw/master/bin/max32625_max32670evkit_if_crc_swd_v1.0.3.bin>`__
+- One (1) CR123A Battery or any equivalent external DC power supply (+3V to +4.7V)
+  **Note that this is not included in the kit**
+- One (1) Micro USB to USB cable
+- Host PC (Windows 10 or later)
+
+.. figure:: hardware_setup.png
+
+#. Insert one CR123A battery (3V to 4.7V) into the battery holder (BT1
+   connector) of the :adi:`MAX32670-LR-ARDZ` Base Board.
+
+   **Make sure to check for the battery polarity in
+   the BT1 connector, refer to the figure below. The DS3 LED will light up
+   indicating that you have inserted the battery correctly and that power is
+   provided in the base board.**
+
+   .. figure:: max32670-lr-ardz_with_battery.png
+
+#. Connect the :adi:`EV-CATTLETAG-ARDZ` Sensor Node to the
+   :adi:`MAX32670-LR-ARDZ` Base Board by aligning the
+   corresponding Arduino headers on each board.
+#. Connect the :adi:`MAX32625PICO` programming adapter to the
+   :adi:`MAX32670-LR-ARDZ` Base Board through the 10-pin
+   ribbon cable.
+
+   **Make sure that the MAX32625PICO programming adapter has been flashed with the
+   correct image before connecting it to the MAX32670-LR-ARDZ Base Board. If you do
+   not know how to load the image, click on the instructions below:**
+
+How to flash the firmware image in the MAX32625PICO
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+#. Download the firmware image: `MAX32625PICO Firmware Image for
+   MAX32670 <https://github.com/analogdevicesinc/max32625pico-firmware-images/raw/master/bin/max32625_max32670evkit_if_crc_swd_v1.0.3.bin>`__
+#. Do not connect the MAX32625PICO to the
+   :adi:`MAX32670-LR-ARDZ` Base Board yet.
+#. Connect the MAX32625PICO to the Host PC using the micro USB to USB cable.
+#. Press the button on the MAX32625PICO. **(Do not release the button until the
+   MAINTENANCE drive is mounted)**.
+
+   .. figure:: max32625pico_maxdap.png
+      :width: 300 px
+
+#. Release the button once the MAINTENANCE drive is mounted.
+#. Drag and drop (to the MAINTENANCE drive) the firmware image.
+#. After a few seconds, the MAINTENANCE drive will disappear and be replaced by
+   a drive named DAPLINK. This indicates that the process is complete, and the
+   MAX32625PICO can now be used to flash the firmware of the
+   :adi:`MAX32670-LR-ARDZ` Base Board.
+
+#. Connect the :adi:`MAX32625PICO` programming adapter to the
+   Host PC using the micro USB to USB cable.
+
+   .. figure:: max32670-lr-ardz_to_maxpico.png
+
+Once you have completed this setup, proceed to PHASE 2 found in
+:dokuwiki:`ADI Long Range Wireless Radio Software UserGuide </resources/eval/user-guides/longrangewirelessradio/software>`.
+
+Resources
+---------
+
+- :adi:`MAX20361 Product Page <MAX20361>`
+- :adi:`MAX20335 Product Page <MAX20335>`
+- :adi:`MAX30210 Product Page <MAX30210>`
+
+Design and Integration Files
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+.. admonition:: Download
+
+   :download:`EV-CATTLETAG-ARDZ Design Support Package Rev. C <ev-cattletag-ardz-designsupport.zip>`
+
+   - Schematic
+   - Bill of Materials
+   - Layout
+   - Fabrication Files
+
+Help and Support
+~~~~~~~~~~~~~~~~
+
+For questions and more information about this product, connect with us through
+the :ez:`Analog Devices Engineer Zone </>`.