Skip to content
Find file
Fetching contributors…
Cannot retrieve contributors at this time
165 lines (126 sloc) 6.74 KB
Information about USB scanners:
With Linux 2.4.* you could either use the kernel scanner module or libusb to
access USB scanners. In Linux 2.6.4 the kernel scanner module was removed.
Therefore with this and later kernels libusb must be used.
While SANE automatically uses libusb when the library and its header file were
present during the build of sane-backends, setting permissions will require some
attention. So if scanimage -L lists your scanner as root but not as normal user
read on this text.
Most distributions support setting permissions without much manual
configuration. Usually you must just add the users that are allowed to access
the scanner to group "scanner". To make that change active, the user must login
again. For more details, see your distribution's documentation e.g. for Debian:
README.debian.gz. If this doesn't work you you want to know more, read on.
The device files used by libusb are located in /proc/bus/usb/
(e.g. /proc/bus/usb/001/003) or in /dev/bus/usb/ (e.g. /dev/bus/usb/001/003), if
you use udev. The exact file name can be found out by running sane-find-scanner
which would print "libusb:001:003" in this case. While setting permissions with
e.g. "chmod a+rw /proc/bus/usb/001/003" works, this change is not permanent.
The permissions will be reset when the scanner is replugged or Linux is
One solution to set permissions on-the-fly is Linux udev which comes with
current distributions. SANE comes with a udev rules file in the tools/udev
directory which may be used by distributions or can be copied to
/etc/udev/rules.d manually. The file format is explained on top of the file
itself. Either you need libusb 0.1.12 or newer or USB_DEVFS_PATH=/dev/bus/usb
must be exported as a system-wide environment variable.
Older distributions may use the Linux hot-plug tools (or hotplug-ng). Your
distribution should have set up the scripts to automatically change permissions
correctly. Look for "libsane.usermap" and "libusbscanner" in /etc/hotplug/usb.
If you build SANE from source you can use the hotplug script that comes with
SANE. See the tools/hotplug/ directory in the source distribution. Please refer
to the README in that directory for the details.
Gentoo information:
Gentoo users: If your USB scanner is not detected at all check that USE=usb is
set when emerging.
Information about SCSI scanners:
Under Linux, your kernel must have generic SCSI support (sg) as well as a
driver for your SCSI adapter. You may want to increase the SCSI buffer size
to increase scan speed. Details on all of the above can be found in
If your SCSI and sg driver are build as moduls you will need to load them
with modprobe:
# modprobe your-driver-name
# modprobe sg
You may find error messages in /var/log/messages. Look at the documentation
for your SCSI driver. Maybe you need to add options like the io port.
Now the SCSI adapter and your scanner should be visible at /proc/scsi/scsi.
# cat /proc/scsi/scsi
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: SCANNER Model: Rev: 2.02
Type: Scanner ANSI SCSI revision: 01 CCS
In this case the real vendor and scanner name are not shown (Mustek
Scannexpress 12000SP) but SANE will detect it nevertheless.
If your scanner is supported by SANE, scanimage -L will list it now:
# scanimage -L
device mustek:/dev/scanner' is a Mustek ScanExpress 12000SP flatbed scanner
If this doesn't work you may have to add the right SCSI generic device name
to the configuration file. This should be documented in the man page for
your backend. To find out about the right SCSI device use sane-find-scanner:
# sane-find-scanner
found SCSI scanner "SCANNER 2.02" at /dev/scanner
found SCSI scanner "SCANNER 2.02" at /dev/sg0
found SCSI scanner "SCANNER 2.02" at /dev/sga
It may help to set a symbolic link /dev/scanner to the respective device if
automatic detection does not work.
If you need more information on the Linux SCSI subsystem, look at Although this
documentation is about the 2.4 kernels, large parts are also valid for
older kernels. One important exception is the section on "Device Names
in devfs".
Adaptec 1542 SCSI adapter:
Using buffer sizes of more than 32768 bytes with the aha1542 driver can
lead to kernel panic with older kernels. To avoid this, run configure with
the option --enable-scsibuffersize or set the environment variable
SANE_SG_BUFFERSIZE to 32768 before running scanimage or another frontend,
or download and install the SG driver 2.1.37 or newer from
The Linux kernel "Emulation of a SCSI host adapter for IDE ATAPI
devices" (idescsi) is reported to cause problems in connection with
SANE. If your scanner isn't found or you encounter segmentation faults
try to disable idescsi.
SCSI Direct IO: Recent versions of the Linux SG driver for the 2.4 kernels
support direct IO, i.e., the SCSI adapter's DMA chip copies data directly
to/from user memory. Direct IO reduces memory usage, but it can lead to
access conflicts, if a backend uses shared memory. SANE does not use
direct IO by default. If you want to use it, run
configure --enable-scsi-directio=yes
Very old Linux distributions are missing the /usr/include/scsi directory. In
such a case, it is necessary to copy the relevant files from the kernel
distribution. Normally, the command:
cp -a /usr/src/linux/include/scsi /usr/include
should fix this problem. Don't do this if you don't get compilation errors
about missing SCSI headers.
Other Information
================= configuration:
"/usr/local/lib/sane" or "/usr/lib/sane" MUST NOT be listed in
/etc/ If your scanner is not detected or only Video for Linux
devices are found, check for one of the above lines in
A line "/usr/local/lib" or "/usr/lib" in is ok, however.
Excessive warnings "pointer of type `void *' used in arithmetic":
Some older versions of glibc generate these warnings not related to SANE
source code. To suppress these warnings do
and rerun configure.
If you use DEC cc on Linux Alpha, you may need to set LDFLAGS="-N" to
be able to build sane-backends.
The Intel C++ Compiler for IA32 and IA64 isn't supported yet. If you want
to try nevertheless, you will experience undefined references to inb
and outb functions. To avoid those replace #include <sys/io.h> with
#if defined(__ICC) && __ICC >= 700
# define __GNUC__ 2
#include <sys/io.h>
#if defined(__ICC) && __ICC >= 700
# undef __GNUC__
#elif defined(__ICC) && defined(HAVE_ASM_IO_H)
# include <asm/io.h>
Jump to Line
Something went wrong with that request. Please try again.