New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
Tasmota reseting itself #5507
Comments
|
Please, could you be so kind on completing the troubleshooting template in order to have more information so as to properly help you? Remember to read the Contributing Guideline and Policy. Thanks. Support Information (Guide)See Wiki for more information. |
|
Hi, Please, when you have time, please, complete the troubleshooting template in order to have more information so as to properly help you. Thanks. |
BUG DESCRIPTIONHallo, I have a simple setup. Wemos d1 2 button and 2 relais. Tasmota 6.5 I have created the following rule: it seem to be working but after after some seconds tasmota reseting himself. Tried on 3 different wemos d1. REQUESTED INFORMATIONMake sure these boxes are checked before submitting your issue. Thank you FAILURE TO COMPLETE THE REQUESTED INFORMATION WILL RESULT IN YOUR ISSUE BEING CLOSED
TO REPRODUCE_Steps to reproduce the behavior: device configuration d5 button2 console websend [xx.xx.xx.36:8181]/cuxd.exe%3Fret=dom.GetObject%28%22Steckdose%20152%22%29.State%281%29 create rule rule press button1 EXPECTED BEHAVIOURwhen I press sometime the button tasmota is deleteing all te setting "reset" by himself SCREENSHOTSIf applicable, add screenshots to help explain your problem. ADDITIONAL CONTEXT09:51:48 SRC: WebConsole from xx.xx.xx.90 (Please, remember to close the issue when the problem has been addressed) |
|
Hi, Thanks for completing the template. In the gpio where you have set the button1, you have connected a pushbutton or a switch? Tasmota has a feature that if you keep pushed the button1 for more than 40 seconds, tasmota will reset all configs. If you have connected a switch, you should be using a switch as a gpio config and also you should select the switchmode that suits better your use case. Also, you can disable the reset feature when pushing the button for more than 40 seconds using the following commands in the Tasmota console:
And
Please, tell us if this solves your issue. Thanks |
|
@FraatRamski Hi, Any news on this? |
|
Is working, thanks for the help! |
|
I know this is old but, just to note that this also solves Xiaomi-Philips Bulb continuous resetting problem. (tasmota 8.3.1) |
FraatGIT commentedMar 21, 2019
•
edited
Hallo,
I have a simple setup. Wemos d1 2 button and 2 relais. Tasmota 6.5
I have created the following rule:
rule
on Power1#State=1 do websend [10.xx.xx.xx:8181]/cuxd.exe%3Fret=dom.GetObject%28%22Steckdose%20152%22%29.State%281%29 endon
on Power1#State=0 do websend [10.xx.xx.xx:8181]/cuxd.exe%3Fret=dom.GetObject%28%22Steckdose%20152%22%29.State%280%29 endon
it seem to be working but after after some seconds tasmota reseting himself. Tried on 3 different wemos d1.
20:11:09 MQT: stat/sonoff/POWER1 = OFF
20:11:09 MQT: stat/sonoff/RESULT = {"POWER2":"OFF"}
20:11:09 MQT: stat/sonoff/POWER2 = OFF
20:11:10 MQT: stat/sonoff/RESULT = {"POWER2":"ON"}
20:11:10 MQT: stat/sonoff/POWER2 = ON
20:11:12 MQT: stat/sonoff/RESULT = {"POWER2":"OFF"}
20:11:12 MQT: stat/sonoff/POWER2 = OFF
20:11:13 MQT: stat/sonoff/RESULT = {"POWER1":"ON"}
20:11:13 MQT: stat/sonoff/POWER1 = ON
20:11:14 MQT: stat/sonoff/RESULT = {"POWER1":"OFF"}
20:11:14 MQT: stat/sonoff/POWER1 = OFF
20:11:17 MQT: tele/sonoff/STATE = {"Time":"2019-03-21T20:11:17","Uptime":"0T00:00:19","Vcc":2.766,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":35,"POWER1
":"OFF","POWER2":"OFF","Wifi":{"AP":1,"SSId":"xxx","BSSId":"76:xx:E7:59:93:31","Channel":11,"RSSI":48,"LinkCount":1,"Downtime":"0T00:00:09"}}
20:11:30 CMD: rule on Power1#State=1 do websend [10.xx.xx.xx:8181]/cuxd.exe%3Fret=dom.GetObject%28%22Steckdose%20152%22%29.State%281%29 endon on Pow
er1#State=0 do websend [10.12.14.36:8181]/cuxd.exe%3Fret=dom.GetObject%28%22Steckdose%20152%22%29.State%280%29 endon
20:11:30 MQT: stat/sonoff/RESULT = {"Rule1":"OFF","Once":"OFF","StopOnError":"OFF","Free":259,"Rules":"on Power1#State=1 do websend [10.xx.xx.xx:8181]/
cuxd.exe%3Fret=dom.GetObject%28%22Steckdose%20152%22%29.State%281%29 endon on Power1#State=0 do websend [10.xx.xx.xx:8181]/cuxd.exe%3Fret=dom.GetObje
ct%28%22Steckdose%20152%22%29.State%280%29 endon"}
20:11:35 CMD: rule1 on
20:11:35 MQT: stat/sonoff/RESULT = {"Rule1":"ON","Once":"OFF","StopOnError":"OFF","Free":259,"Rules":"on Power1#State=1 do websend [10.xx.xx.xx:8181]/c
uxd.exe%3Fret=dom.GetObject%28%22Steckdose%20152%22%29.State%281%29 endon on Power1#State=0 do websend [10.xx.xx.xx:8181]/cuxd.exe%3Fret=dom.GetObjec
t%28%22Steckdose%20152%22%29.State%280%29 endon"}
20:11:46 MQT: stat/sonoff/RESULT = {"POWER1":"ON"}
20:11:46 MQT: stat/sonoff/POWER1 = ON
20:11:46 RUL: POWER1#STATE=1 performs "websend [10.xx.xx.xx:8181]/cuxd.exe%3Fret=dom.GetObject%28%22Steckdose%20152%22%29.State%281%29"
20:11:46 MQT: stat/sonoff/RESULT = {"WebSend":"Done"}
20:11:49 MQT: stat/sonoff/RESULT = {"Reset":"Reset and Restarting"}
20:11:49 CFG: Standard verwenden
20:11:50 APP: starte neu
The text was updated successfully, but these errors were encountered: