DDR Version 1.11 20180509 In Channel 0: LPDDR4,50MHz CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x4D MR14=0x4D MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x4D MR14=0x4D MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB Channel 1: LPDDR4,50MHz CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x4D MR14=0x4D MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x4D MR14=0x4D MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB 256B stride channel 0 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 400MHz 0,1 channel 0 CS = 0 MR0=0x98 MR4=0x81 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x81 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x81 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 800MHz 1,0 ch 0 ddrconfig = 0x101, ddrsize = 0x2020 ch 1 ddrconfig = 0x101, ddrsize = 0x2020 pmugrf_os_reg[2] = 0x3AA1FAA1, stride = 0xD OUT U-Boot SPL board init U-Boot SPL 2017.09-gec1524d (Jun 02 2018 - 21:27:10) booted from SD Trying to boot from MMC2 NOTICE: BL31: v1.3(debug):d98d16e NOTICE: BL31: Built : 15:03:07, May 10 2018 NOTICE: BL31: Rockchip release version: v1.1 INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 0 INFO: plat_rockchip_pmu_init(1151): pd status 3e INFO: BL31: Initializing runtime services WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK ERROR: Error initializing runtime service opteed_fast INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9 U-Boot 2017.09-gec1524d (Jun 02 2018 - 21:27:23 +0000), Build: jenkins-linux-build-rock-64-247 Model: Pine64 RockPro64 DRAM: 3.9 GiB MMC: sdhci@fe330000: 0, dwmmc@fe320000: 1 Card did not respond to voltage select! mmc_init: -95, time 21 *** Warning - No block device, using default environment In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: Pine64 RockPro64 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 Card did not respond to voltage select! mmc_init: -95, time 22 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:6... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf reading /extlinux/extlinux.conf 688 bytes read in 8 ms (84 KiB/s) select kernel 1: kernel-latest 2: kernel-previous Enter choice: 1: kernel-latest Retrieving file: /initrd.img reading /initrd.img 6350230 bytes read in 284 ms (21.3 MiB/s) Retrieving file: /Image reading /Image 19490824 bytes read in 858 ms (21.7 MiB/s) append: rw root=LABEL=linux-root rootwait rootfstype=ext4 panic=10 init=/sbin/init coherent_pool=1M ethaddr=26:12:90:d2:f2:ea eth1addr= serial=ef88ee27f7d8e6d cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 Retrieving file: /dtb reading /dtb 69174 bytes read in 10 ms (6.6 MiB/s) ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Loading Ramdisk to f58f6000, end f5f04596 ... OK Loading Device Tree to 00000000f58e2000, end 00000000f58f5e35 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.126-rockchip-ayufan-247 (root@251d97060a57) (gcc version 7.2.0 (Ubuntu/Linaro 7.2.0-6ubuntu1) ) #1 SMP Sat Jun 2 21:31:15 UTC 2018 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0f7eea000 s46248 r8192 d31576 u86016 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 999432 [ 0.000000] Kernel command line: earlyprintk=uart8250-32bit,0xff1a0000 swiotlb=1 rw root=LABEL=linux-root rootwait rootfstype=ext4 panic=10 init=/sbin/init coherent_pool=1M ethaddr=26:12:90:d2:f2:ea eth1addr= serial=ef88ee27f7d8e6d cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] software IO TLB [mem 0xf7ea2000-0xf7ee2000] (0MB) mapped at [ffffffc0f7ea2000-ffffffc0f7ee1fff] [ 0.000000] Memory: 3961980K/4061184K available (11838K kernel code, 1690K rwdata, 4276K rodata, 1152K init, 749K bss, 99204K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] .init : 0xffffff8009050000 - 0xffffff8009170000 ( 1152 KB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008c10000 ( 11840 KB) [ 0.000000] .rodata : 0xffffff8008c10000 - 0xffffff8009050000 ( 4352 KB) [ 0.000000] .data : 0xffffff8009170000 - 0xffffff8009316808 ( 1691 KB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc0008000 - 0xffffffbdc3e00000 ( 61 MB actual) [ 0.000000] fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB) [ 0.000000] memory : 0xffffffc000200000 - 0xffffffc0f8000000 ( 3966 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000 [ 0.000000] ITS: allocated 65536 Devices @f2900000 (psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GIC: using LPI property table @0x00000000f2890000 [ 0.000000] ITS: Allocated 1792 chunks for LPIs [ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000 [ 0.000000] CPU0: using LPI pending table @0x00000000f28a0000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] } [ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] } [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.001231] Console: colour dummy device 80x25 [ 0.002934] console [tty0] enabled [ 0.002977] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000) [ 0.003037] pid_max: default: 32768 minimum: 301 [ 0.003190] Security Framework initialized [ 0.003224] Yama: becoming mindful. [ 0.003272] AppArmor: AppArmor disabled by boot time parameter [ 0.003352] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003390] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.004174] Initializing cgroup subsys io [ 0.004231] Initializing cgroup subsys memory [ 0.004286] Initializing cgroup subsys devices [ 0.004325] Initializing cgroup subsys freezer [ 0.004362] Initializing cgroup subsys net_cls [ 0.004398] Initializing cgroup subsys perf_event [ 0.004436] Initializing cgroup subsys net_prio [ 0.004477] Initializing cgroup subsys hugetlb [ 0.004511] Initializing cgroup subsys pids [ 0.004577] ftrace: allocating 43925 entries in 172 pages [ 0.118454] sched-energy: Sched-energy-costs installed from DT [ 0.118502] CPU0: update cpu_capacity 401 [ 0.118584] ASID allocator initialised with 32768 entries [ 0.121821] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created [ 0.122352] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created [ 0.123643] Detected VIPT I-cache on CPU1 [ 0.123675] CPU1: found redistributor 1 region 0:0x00000000fef20000 [ 0.123706] CPU1: using LPI pending table @0x00000000f2b40000 [ 0.123749] CPU1: update cpu_capacity 401 [ 0.123753] CPU1: Booted secondary processor [410fd034] [ 0.124283] Detected VIPT I-cache on CPU2 [ 0.124304] CPU2: found redistributor 2 region 0:0x00000000fef40000 [ 0.124332] CPU2: using LPI pending table @0x00000000f2b60000 [ 0.124361] CPU2: update cpu_capacity 401 [ 0.124364] CPU2: Booted secondary processor [410fd034] [ 0.124893] Detected VIPT I-cache on CPU3 [ 0.124913] CPU3: found redistributor 3 region 0:0x00000000fef60000 [ 0.124941] CPU3: using LPI pending table @0x00000000f2bc0000 [ 0.124968] CPU3: update cpu_capacity 401 [ 0.124972] CPU3: Booted secondary processor [410fd034] [ 0.125489] Detected PIPT I-cache on CPU4 [ 0.125515] CPU4: found redistributor 100 region 0:0x00000000fef80000 [ 0.125554] CPU4: using LPI pending table @0x00000000f2bf0000 [ 0.125593] CPU4: update cpu_capacity 1024 [ 0.125597] CPU4: Booted secondary processor [410fd082] [ 0.126132] Detected PIPT I-cache on CPU5 [ 0.126151] CPU5: found redistributor 101 region 0:0x00000000fefa0000 [ 0.126187] CPU5: using LPI pending table @0x00000000f2020000 [ 0.126216] CPU5: update cpu_capacity 1024 [ 0.126219] CPU5: Booted secondary processor [410fd082] [ 0.126307] Brought up 6 CPUs [ 0.127005] SMP: Total of 6 processors activated. [ 0.127037] CPU features: detected feature: GIC system register CPU interface [ 0.127075] CPU: All CPU(s) started at EL2 [ 0.127144] alternatives: patching kernel code [ 0.128634] devtmpfs: initialized [ 0.142399] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.142455] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.142971] xor: measuring software checksum speed [ 0.152652] 8regs : 2876.000 MB/sec [ 0.162707] 8regs_prefetch: 2580.000 MB/sec [ 0.172763] 32regs : 3244.000 MB/sec [ 0.182820] 32regs_prefetch: 2868.000 MB/sec [ 0.182839] xor: using function: 32regs (3244.000 MB/sec) [ 0.182883] pinctrl core: initialized pinctrl subsystem [ 0.184353] Failed to find legacy iommu devices [ 0.184757] NET: Registered protocol family 16 [ 0.189786] cpuidle: using governor ladder [ 0.193793] cpuidle: using governor menu [ 0.194098] vdso: 2 pages (1 code @ ffffff8008c16000, 1 data @ ffffff8009174000) [ 0.194153] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.194694] DMA: preallocated 1024 KiB pool for atomic allocations [ 0.245236] raid6: int64x1 gen() 472 MB/s [ 0.262349] raid6: int64x1 xor() 419 MB/s [ 0.279401] raid6: int64x2 gen() 656 MB/s [ 0.296502] raid6: int64x2 xor() 607 MB/s [ 0.313602] raid6: int64x4 gen() 960 MB/s [ 0.330672] raid6: int64x4 xor() 671 MB/s [ 0.347792] raid6: int64x8 gen() 753 MB/s [ 0.364897] raid6: int64x8 xor() 628 MB/s [ 0.381989] raid6: neonx1 gen() 996 MB/s [ 0.399068] raid6: neonx1 xor() 673 MB/s [ 0.416180] raid6: neonx2 gen() 1332 MB/s [ 0.433257] raid6: neonx2 xor() 994 MB/s [ 0.450372] raid6: neonx4 gen() 1796 MB/s [ 0.467458] raid6: neonx4 xor() 1201 MB/s [ 0.484550] raid6: neonx8 gen() 1695 MB/s [ 0.501648] raid6: neonx8 xor() 1265 MB/s [ 0.501667] raid6: using algorithm neonx4 gen() 1796 MB/s [ 0.501685] raid6: .... xor() 1201 MB/s, rmw enabled [ 0.501704] raid6: using intx1 recovery algorithm [ 0.503336] vcc3v3_pcie: supplied by dc_12v [ 0.503866] vcc_sys: supplied by dc_12v [ 0.504405] vcc3v3_sys: supplied by vcc_sys [ 0.506491] SCSI subsystem initialized [ 0.506685] usbcore: registered new interface driver usbfs [ 0.506740] usbcore: registered new interface driver hub [ 0.506840] usbcore: registered new device driver usb [ 0.506952] media: Linux media interface: v0.10 [ 0.506999] Linux video capture interface: v2.00 [ 0.507074] pps_core: LinuxPPS API ver. 1 registered [ 0.507093] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.507142] PTP clock support registered [ 0.508443] Advanced Linux Sound Architecture Driver Initialized. [ 0.509020] Bluetooth: Core ver 2.21 [ 0.509064] NET: Registered protocol family 31 [ 0.509084] Bluetooth: HCI device and connection manager initialized [ 0.509109] Bluetooth: HCI socket layer initialized [ 0.509132] Bluetooth: L2CAP socket layer initialized [ 0.509169] Bluetooth: SCO socket layer initialized [ 0.509583] NetLabel: Initializing [ 0.509603] NetLabel: domain hash size = 128 [ 0.509621] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.509668] NetLabel: unlabeled traffic allowed by default [ 0.510440] clocksource: Switched to clocksource arch_sys_counter [ 0.562251] thermal thermal_zone1: power_allocator: sustainable_power will be estimated [ 0.562538] NET: Registered protocol family 2 [ 0.563010] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.563217] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes) [ 0.563907] TCP: Hash tables configured (established 32768 bind 32768) [ 0.564050] UDP hash table entries: 2048 (order: 5, 196608 bytes) [ 0.564276] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes) [ 0.564721] NET: Registered protocol family 1 [ 0.565062] RPC: Registered named UNIX socket transport module. [ 0.565084] RPC: Registered udp transport module. [ 0.565102] RPC: Registered tcp transport module. [ 0.565121] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.565864] Trying to unpack rootfs image as initramfs... [ 0.872252] Freeing initrd memory: 6200K [ 0.872791] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 0.872910] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available [ 0.874149] kvm [1]: 8-bit VMID [ 0.874170] kvm [1]: Hyp mode initialized successfully [ 0.874314] kvm [1]: interrupt-controller@fff20000 IRQ10 [ 0.874558] kvm [1]: timer IRQ12 [ 0.877421] audit: initializing netlink subsys (disabled) [ 0.877489] audit: type=2000 audit(0.801:1): initialized [ 0.878216] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.885325] VFS: Disk quotas dquot_6.6.0 [ 0.885516] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.887183] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.888377] NFS: Registering the id_resolver key type [ 0.888419] Key type id_resolver registered [ 0.888460] Key type id_legacy registered [ 0.888495] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.889165] fuse init (API version 7.23) [ 0.889902] JFS: nTxBlock = 8192, nTxLock = 65536 [ 0.895656] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 0.897313] Key type big_key registered [ 0.897383] [ 0.897383] TEE Core Framework initialization (ver 1:0.1) [ 0.897455] TEE armv7 Driver initialization [ 0.897884] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0" [ 0.897909] TEE core: Alloc the misc device "opteearmtz00" (id=0) [ 0.898117] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62) [ 0.902103] NET: Registered protocol family 38 [ 0.902150] Key type asymmetric registered [ 0.902175] Asymmetric key parser 'x509' registered [ 0.902380] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.902555] io scheduler noop registered [ 0.902583] io scheduler deadline registered (default) [ 0.902634] io scheduler cfq registered [ 0.904011] phy phy-ff770000.syscon:usb2-phy@e460.0: Failed to get VBUS supply regulator [ 0.908892] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found [ 0.908937] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found [ 0.929482] rockchip-pcie f8000000.pcie: invalid power supply [ 1.429537] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout! [ 1.429779] rockchip-pcie: probe of f8000000.pcie failed with error -110 [ 1.432688] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.432748] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12 [ 1.434963] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.435020] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 [ 1.437658] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled [ 1.439323] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 36, base_baud = 1500000) is a 16550A [ 1.439935] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 37, base_baud = 1500000) is a 16550A [ 1.555346] console [ttyS2] enabled [ 1.556691] [drm] Initialized drm 1.1.0 20060810 [ 1.560325] [drm] Rockchip DRM driver version: v1.0.1 [ 1.560835] rockchip-drm display-subsystem: No available vop found for display-subsystem. [ 1.561864] usbcore: registered new interface driver udl [ 1.563732] Unable to detect cache hierarchy for CPU 0 [ 1.565019] brd: module loaded [ 1.570656] loop: module loaded [ 1.571210] lkdtm: No crash points registered, enable through debugfs [ 1.574032] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input). [ 1.574690] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28). [ 1.575208] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20). [ 1.575748] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no). [ 1.576488] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed [ 1.577117] rk_gmac-dwmac fe300000.ethernet: clock input from PHY [ 1.582685] rk_gmac-dwmac fe300000.ethernet: init for RGMII [ 1.583312] stmmac - user ID: 0x10, Synopsys ID: 0x35 [ 1.583784] Ring mode enabled [ 1.584070] DMA HW capability register supported [ 1.584481] Normal descriptors [ 1.584802] RX Checksum Offload Engine supported (type 2) [ 1.585299] TX Checksum insertion supported [ 1.585697] Wake-Up On Lan supported [ 1.586068] Enable RX Mitigation via HW Watchdog Timer [ 1.655713] libphy: stmmac: probed [ 1.656055] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active [ 1.656661] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01) [ 1.659057] Rockchip WiFi SYS interface (V1.00) ... [ 1.659670] usbcore: registered new interface driver cdc_ether [ 1.660242] usbcore: registered new interface driver rndis_host [ 1.662165] rockchip-dwc3 usb@fe800000: failed to get drvdata dwc3 [ 1.668193] rockchip-dwc3 usb@fe900000: fail to get drvdata hcd [ 1.669924] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.670552] ehci-pci: EHCI PCI platform driver [ 1.671020] ehci-platform: EHCI generic platform driver [ 1.675399] ehci-platform fe3c0000.usb: EHCI Host Controller [ 1.676085] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1 [ 1.676917] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000 [ 1.683466] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00 [ 1.684182] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.684812] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.685482] usb usb1: Product: EHCI Host Controller [ 1.685930] usb usb1: Manufacturer: Linux 4.4.126-rockchip-ayufan-247 ehci_hcd [ 1.686599] usb usb1: SerialNumber: fe3c0000.usb [ 1.687512] hub 1-0:1.0: USB hub found [ 1.687885] hub 1-0:1.0: 1 port detected [ 1.688779] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.689357] ohci-platform: OHCI generic platform driver [ 1.690331] ohci-platform fe3e0000.usb: Generic Platform OHCI controller [ 1.691100] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2 [ 1.691914] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000 [ 1.747604] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.748221] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.748894] usb usb2: Product: Generic Platform OHCI controller [ 1.749441] usb usb2: Manufacturer: Linux 4.4.126-rockchip-ayufan-247 ohci_hcd [ 1.750102] usb usb2: SerialNumber: fe3e0000.usb [ 1.750951] hub 2-0:1.0: USB hub found [ 1.751327] hub 2-0:1.0: 1 port detected [ 1.753458] usbcore: registered new interface driver iforce [ 1.754019] usbcore: registered new interface driver xpad [ 1.754824] usbcore: registered new interface driver usbtouchscreen [ 1.755655] .. rk pwm remotectl v1.1 init [ 1.756273] input: ff420030.pwm as /devices/platform/ff420030.pwm/input/input0 [ 1.757717] i2c /dev entries driver [ 1.759276] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! [ 1.759977] fan53555-reg: supplied by vcc_sys [ 1.762841] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! [ 1.763527] fan53555-reg: supplied by vcc_sys [ 1.766557] rk808 0-001b: Pmic Chip id: 0x0 [ 1.770296] rk808-regulator rk808-regulator: there is no dvs0 gpio [ 1.770921] rk808-regulator rk808-regulator: there is no dvs1 gpio [ 1.771585] DCDC_REG1: supplied by vcc_sys [ 1.772760] DCDC_REG2: supplied by vcc_sys [ 1.773742] DCDC_REG3: supplied by vcc_sys [ 1.774442] DCDC_REG4: supplied by vcc_sys [ 1.775311] LDO_REG1: supplied by vcc_sys [ 1.776868] LDO_REG2: supplied by vcc_sys [ 1.778250] LDO_REG3: supplied by vcc_sys [ 1.779672] LDO_REG4: supplied by vcc_sys [ 1.781050] LDO_REG5: supplied by vcc_sys [ 1.782468] LDO_REG6: supplied by vcc_sys [ 1.783863] LDO_REG7: supplied by vcc_sys [ 1.785258] LDO_REG8: supplied by vcc_sys [ 1.786683] SWITCH_REG1: supplied by vcc3v3_sys [ 1.787407] SWITCH_REG2: supplied by vcc3v3_sys [ 1.792188] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0 [ 1.793256] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff8009bfa000 [ 1.794581] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff8009bfc000 [ 1.796374] fusb302 4-0022: Can't get property of role, set role to default DRP [ 1.805362] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE [ 1.806228] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff8009bfe000 [ 1.807976] IR NEC protocol handler initialized [ 1.808397] IR RC5(x/sz) protocol handler initialized [ 1.808873] IR RC6 protocol handler initialized [ 1.809293] IR JVC protocol handler initialized [ 1.809722] IR Sony protocol handler initialized [ 1.810150] IR SANYO protocol handler initialized [ 1.810593] IR Sharp protocol handler initialized [ 1.811027] IR MCE Keyboard/mouse protocol handler initialized [ 1.811570] IR XMP protocol handler initialized [ 1.812338] usbcore: registered new interface driver uvcvideo [ 1.812870] USB Video Class driver (1.1.1) [ 1.815815] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647 [ 1.817791] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 1.818611] Bluetooth: Virtual HCI driver ver 1.5 [ 1.819146] Bluetooth: HCI UART driver ver 2.3 [ 1.819570] Bluetooth: HCI UART protocol H4 registered [ 1.820038] Bluetooth: HCI UART protocol LL registered [ 1.820516] Bluetooth: HCI UART protocol ATH3K registered [ 1.821071] usbcore: registered new interface driver bfusb [ 1.821633] usbcore: registered new interface driver btusb [ 1.822562] cpu cpu0: cpu_leakage=24 [ 1.822942] cpu cpu0: cpu_leakage=24 [ 1.835308] cpu cpu0: temp=33888, pvtm=145616 (146536 + -920) [ 1.836337] cpu cpu4: cpu_leakage=42 [ 1.836762] cpu cpu4: cpu_leakage=42 [ 1.849364] cpu cpu4: temp=33333, pvtm=153305 (153873 + -568) [ 1.854573] sdhci: Secure Digital Host Controller Interface driver [ 1.855137] sdhci: Copyright(c) Pierre Ossman [ 1.855555] Synopsys Designware Multimedia Card Interface Driver [ 1.856957] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode. [ 1.857661] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller. [ 1.858284] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a [ 1.858859] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo [ 1.859773] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated. [ 1.860591] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found [ 1.861152] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found [ 1.862578] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode. [ 1.863259] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller. [ 1.863896] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a [ 1.864461] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo [ 1.865352] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated. [ 1.866197] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found [ 1.867020] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done [ 1.867862] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done [ 1.879500] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 1.890504] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized [ 1.891326] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.893513] sdhci-arasan fe330000.sdhci: No vmmc regulator found [ 1.894067] sdhci-arasan fe330000.sdhci: No vqmmc regulator found [ 1.920516] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA [ 1.922882] hidraw: raw HID events driver (C) Jiri Kosina [ 1.928157] usbcore: registered new interface driver usbhid [ 1.928718] usbhid: USB HID core driver [ 1.930288] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 1.933882] mmc0: new high speed SDHC card at address 0002 [ 1.935063] mmcblk0: mmc0:0002 SD32G 30.0 GiB [ 1.937363] ff100000.saradc supply vref not found, using dummy regulator [ 1.939752] usbcore: registered new interface driver snd-usb-audio [ 1.941182] es8316 1-0010: Can not read property spk_ctl_gpio [ 1.949559] u32 classifier [ 1.949867] Netfilter messages via NETLINK v0.30. [ 1.950395] ip_set: protocol 6 [ 1.951099] Initializing XFRM netlink socket [ 1.952771] NET: Registered protocol family 10 [ 1.955141] NET: Registered protocol family 17 [ 1.955626] NET: Registered protocol family 15 [ 1.956084] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.957283] Bridge firewalling registered [ 1.958006] Bluetooth: RFCOMM socket layer initialized [ 1.958569] Bluetooth: RFCOMM ver 1.11 [ 1.958942] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.959511] Bluetooth: HIDP socket layer initialized [ 1.960052] 8021q: 802.1Q VLAN Support v1.8 [ 1.960492] [WLAN_RFKILL]: Enter rfkill_wlan_init [ 1.960609] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 1.960619] GPT:4458495 != 62873599 [ 1.960623] GPT:Alternate GPT header not at the end of the disk. [ 1.960628] GPT:4458495 != 62873599 [ 1.960631] GPT: Use GNU Parted to correct GPT errors. [ 1.960703] mmcblk0: p1 p2 p3 p4 p5 p6 p7 [ 1.964243] [WLAN_RFKILL]: Enter rfkill_wlan_probe [ 1.964789] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6354 [ 1.965421] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control. [ 1.966086] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio. [ 1.966896] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0. [ 1.967746] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio [ 1.968236] [WLAN_RFKILL]: Exit rfkill_wlan_probe [ 1.968771] [BT_RFKILL]: Enter rfkill_rk_init [ 1.969848] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83. [ 1.970669] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9. [ 1.971458] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 91. [ 1.972232] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4. [ 1.973516] [BT_RFKILL]: Request irq for bt wakeup host [ 1.974064] [BT_RFKILL]: ** disable irq [ 1.974630] [BT_RFKILL]: bt_default device registered. [ 1.975233] Key type dns_resolver registered [ 1.976779] Registered cp15_barrier emulation handler [ 1.977350] Registered setend emulation handler [ 1.979587] registered taskstats version 1 [ 1.983049] Btrfs loaded, integrity-checker=on [ 1.983598] BTRFS: selftest: Running btrfs free space cache tests [ 1.984185] BTRFS: selftest: Running extent only tests [ 1.984695] BTRFS: selftest: Running bitmap only tests [ 1.985199] BTRFS: selftest: Running bitmap and extent tests [ 1.985763] BTRFS: selftest: Running space stealing from bitmap to extent [ 1.987692] BTRFS: selftest: Free space cache tests finished [ 1.988218] BTRFS: selftest: Running extent buffer operation tests [ 1.988765] BTRFS: selftest: Running btrfs_split_item tests [ 1.989368] BTRFS: selftest: Running find delalloc tests [ 2.221639] BTRFS: selftest: Running btrfs_get_extent tests [ 2.222312] BTRFS: selftest: Running hole first btrfs_get_extent test [ 2.222939] BTRFS: selftest: Running outstanding_extents tests [ 2.223507] BTRFS: selftest: Running qgroup tests [ 2.223929] BTRFS: selftest: Qgroup basic add [ 2.224358] BTRFS: selftest: Qgroup multiple refs test [ 2.236530] phy phy-ff770000.syscon:usb2-phy@e450.6: Failed to get VBUS supply regulator [ 2.250132] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.251580] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3 [ 2.252708] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010 [ 2.253693] xhci-hcd xhci-hcd.0.auto: irq 222, io mem 0xfe800000 [ 2.254685] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.255354] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.256119] usb usb3: Product: xHCI Host Controller [ 2.256645] usb usb3: Manufacturer: Linux 4.4.126-rockchip-ayufan-247 xhci-hcd [ 2.257381] usb usb3: SerialNumber: xhci-hcd.0.auto [ 2.259614] hub 3-0:1.0: USB hub found [ 2.260082] hub 3-0:1.0: 1 port detected [ 2.261236] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.262630] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4 [ 2.263667] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.264790] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 2.265489] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.266227] usb usb4: Product: xHCI Host Controller [ 2.266747] usb usb4: Manufacturer: Linux 4.4.126-rockchip-ayufan-247 xhci-hcd [ 2.267508] usb usb4: SerialNumber: xhci-hcd.0.auto [ 2.269790] hub 4-0:1.0: USB hub found [ 2.270271] hub 4-0:1.0: 1 port detected [ 2.274042] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 2.274622] usb usb4: USB disconnect, device number 1 [ 2.300173] xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds. [ 2.300939] xhci-hcd xhci-hcd.0.auto: Host controller not halted, aborting reset. [ 2.301760] xhci-hcd xhci-hcd.0.auto: USB bus 4 deregistered [ 2.302705] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 2.303215] usb usb3: USB disconnect, device number 1 [ 2.304649] xhci-hcd xhci-hcd.0.auto: USB bus 3 deregistered [ 2.312469] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.313620] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 2.314585] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010 [ 2.315502] xhci-hcd xhci-hcd.1.auto: irq 223, io mem 0xfe900000 [ 2.316348] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.317016] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.317735] usb usb3: Product: xHCI Host Controller [ 2.318206] usb usb3: Manufacturer: Linux 4.4.126-rockchip-ayufan-247 xhci-hcd [ 2.318925] usb usb3: SerialNumber: xhci-hcd.1.auto [ 2.320507] hub 3-0:1.0: USB hub found [ 2.320922] hub 3-0:1.0: 1 port detected [ 2.321832] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.323051] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 2.323990] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.324996] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 2.325667] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.326370] usb usb4: Product: xHCI Host Controller [ 2.326858] usb usb4: Manufacturer: Linux 4.4.126-rockchip-ayufan-247 xhci-hcd [ 2.327574] usb usb4: SerialNumber: xhci-hcd.1.auto [ 2.329610] hub 4-0:1.0: USB hub found [ 2.330046] hub 4-0:1.0: 1 port detected [ 2.335753] ehci-platform fe380000.usb: EHCI Host Controller [ 2.336710] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5 [ 2.337666] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000 [ 2.343766] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00 [ 2.344762] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.345406] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.346130] usb usb5: Product: EHCI Host Controller [ 2.346619] usb usb5: Manufacturer: Linux 4.4.126-rockchip-ayufan-247 ehci_hcd [ 2.347320] usb usb5: SerialNumber: fe380000.usb [ 2.348751] hub 5-0:1.0: USB hub found [ 2.349165] hub 5-0:1.0: 1 port detected [ 2.351066] ohci-platform fe3a0000.usb: Generic Platform OHCI controller [ 2.352044] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6 [ 2.352981] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000 [ 2.409199] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.409917] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.410679] usb usb6: Product: Generic Platform OHCI controller [ 2.411267] usb usb6: Manufacturer: Linux 4.4.126-rockchip-ayufan-247 ohci_hcd [ 2.412026] usb usb6: SerialNumber: fe3a0000.usb [ 2.413890] hub 6-0:1.0: USB hub found [ 2.414343] hub 6-0:1.0: 1 port detected [ 2.417948] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode. [ 2.418769] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller. [ 2.419473] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a [ 2.420087] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo [ 2.421123] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated. [ 2.422208] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found [ 2.422843] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found [ 2.424211] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq [ 2.435784] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 2.447841] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized [ 2.473804] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0) [ 2.513685] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0) [ 2.553655] asoc-simple-card es8316-sound: ES8316 HiFi <-> ff890000.i2s mapping ok [ 2.554501] asoc-simple-card es8316-sound: ASoC: no source widget found for MICBIAS1 [ 2.555286] asoc-simple-card es8316-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack [ 2.556215] asoc-simple-card es8316-sound: ASoC: no sink widget found for IN1P [ 2.556976] asoc-simple-card es8316-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P [ 2.558312] es8316 1-0010: ASoC: Failed to create Left Hp mixer debugfs file [ 2.559040] es8316 1-0010: ASoC: Failed to create Right Hp mixer debugfs file [ 2.559793] es8316 1-0010: ASoC: Failed to create HPCP L debugfs file [ 2.560459] es8316 1-0010: ASoC: Failed to create HPCP R debugfs file [ 2.561123] es8316 1-0010: ASoC: Failed to create HPVOL L debugfs file [ 2.561796] es8316 1-0010: ASoC: Failed to create HPVOL R debugfs file [ 2.568836] rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:50:08 UTC (1358499008) [ 2.569772] of_cfs_init [ 2.570137] of_cfs_init: OK [ 2.606424] vcc3v3_pcie: disabling [ 2.607852] input: rk29-keypad as /devices/platform/rockchip-key/input/input1 [ 2.610302] ALSA device list: [ 2.610608] #0: rockchip,es8316-codec [ 2.611239] ttyS2 - failed to request DMA, use interrupt mode [ 2.612332] Freeing unused kernel memory: 1152K