Skip to content

Bluetooth to USB HID relay using a Raspberry Pi Zero 2 W (or any OTG enabled single board computer)

License

Notifications You must be signed in to change notification settings

bahaaador/bluetooth-usb-peripheral-relay

Repository files navigation

Bluetooth USB HID Relay

A delightfully over-engineered solution to an unusual modern problem!

Use Bluetooth peripherals with Bluetooth-disabled computers.

Bluetooth USB HID Relay Overview

This project creates a Bluetooth USB HID relay using a Raspberry Pi Zero (or similar OTG-enabled single-board computer). It allows you to use Bluetooth keyboards and mice with computers that have Bluetooth disabled, by presenting the board as a composite USB HID device.

Inspiration

This project was born out of a desire to help a friend who couldn't use his favorite Bluetooth mouse and keyboard due to Bluetooth being disabled on his work laptop. As someone who enjoys tinkering and problem-solving, I saw this as an opportunity to create something useful while learning more about Linux internals, USB gadgets, and Go programming. The Raspberry Pi Zero became the perfect bridge, connecting Bluetooth peripherals to computers that wouldn't normally allow it.

graph TD
    B(Keyboard) -- Bluetooth -->  A{"HID <br> (Raspberry Pi Zero)"}
    C(Mouse) -- Bluetooth --> A
    A -- USB--> D(Host Computer)
Loading

Features

  • Connects to Bluetooth keyboards and mice
  • Presents itself as a composite USB HID device (keyboard and mouse) to the host computer
  • Works with Windows, Mac, and Linux computers
  • Automatically starts the relay service at boot
  • Configures the board as a USB OTG device
  • Includes a script to help pair Bluetooth devices

Components

  • Raspberry Pi Zero or other single-board computer capable of USB OTG
  • DietPi or another lightweight Linux distribution
  • Bash scripts for setup and configuration
  • Go program for handling Bluetooth input and USB HID output
  • Systemd service for automatic startup

Requirements & Compatibility

Hardware

  • Tested on: Raspberry Pi Zero W 2
  • Should work on: Any Single Board Computer (SBC) with USB OTG or USB host capabilities
  • Key requirement: Device must be able to act as a USB gadget

Software Prerequisites

Before building and running the project, ensure you have the following installed:

  1. Go (version 1.21 or later)

    On most Linux distributions, including Raspberry Pi OS (formerly Raspbian), you can install Go using:

    sudo apt-get update
    sudo apt-get install golang
  2. Task runner using:

    sh -c "$(curl --location https://taskfile.dev/install.sh)" -- -d -b ~/.local/bin

    or

    go install github.com/go-task/task/v3/cmd/task@latest

Note: You may need to add $(go env GOPATH)/bin to your PATH environment variable with the second command.

⚠️ Caution

Please read before proceeding:

This project is currently in an experimental state and has only been tested on a limited number of devices. While it works well for my use case, please be aware that:

  • The scripts modify system-level configurations and USB settings
  • Incorrect USB gadget configuration could potentially require a fresh OS installation to recover
  • The project has only been tested on a small number of devices and configurations
  • This is a personal project, not production-ready software

Before running this project, you should:

  • Only use it on devices where you can easily reinstall the OS if needed
  • Carefully review all scripts and code before execution
  • Have a backup plan in case something goes wrong
  • Be comfortable with Linux system administration and USB configurations

I cannot guarantee this will work on all devices or configurations. Proceed at your own risk.

Setup

  1. Log in to your Raspberry Pi Zero.

  2. Clone this repository to your board.

  3. Run the setup scripts in the following order:

    sudo chmod +x scripts/*.sh # make sure all scripts are executable
    sudo ./scripts/setup_usb_host.sh # enable the USB host and load the necessary modules
    sudo reboot
    sudo ./scripts/setup_bluetooth.sh # enable and start the bluetooth service
    sudo ./scripts/setup_gadgets.sh # create the gadget and configure the USB strings
  4. Pair your Bluetooth devices manually or using the script:

    sudo ./scripts/pair_devices.sh
  5. Build and install the service:

    task build
    sudo task service:install

Usage

Connect the board to the target computer via USB. This will turn the board on and start the service automatically (assuming it was installed and enabled using the steps above) the bluetooth peripherals should connect automatically as well and the service will retry if they are not connected momentarily. Both Windows and MacOS have been tested and should work.

Tasks

This project uses Task runner for common operations:

General tasks

  • task --list - List all available tasks
  • task build - Build the project
  • task clean - Clean build artifacts
  • task test - Run tests
  • task run - Build and run the application
  • task doctor - Run the diagnose tool
  • task simulate - Run the simulate tool

Service Management

  • task service:install - Install and enable the service
  • task service:status - Check service status
  • task service:logs - View service logs
  • task service:restart - Restart the service
  • task service:start - Start the service
  • task service:stop - Stop the service
  • task service:uninstall - Remove the service

Diagnostic Tools

I/O Doctor

This tool will check for connected Bluetooth devices and display all incoming events from your Bluetooth keyboard and mouse, helping you debug connection and input issues.

task doctor

Input Simulation

To test the USB HID output without Bluetooth devices:

task simulate

This interactive tool allows you to:

  1. Move the mouse in a circle pattern
  2. Type a test message These simulations help verify that the USB HID device is working correctly on the host computer.

Uninstall and remove gadget

To uninstall the service:

task service:uninstall

To remove the gadget and restore the USB host configuration:

./scripts/uninstall/undo_setup_gadgets.sh
./scripts/uninstall/undo_setup_usb_host.sh

Development

This project can be used as is or as basis for other types of USB gadgets. It can also serve as a learning opportunity for:

  • Linux internals
  • Creating USB gadgets
  • Using Go for hardware interfacing
  • Setting up systemd services
  • Configuring single-board computers as USB OTG devices
  • Bluetooth device pairing and management

It's been a fun journey of discovery, and I hope others find it useful or inspiring for their own projects!

Compatibility

Tested with DietPi 64bit as host and Windows 10 and MacOS USB clients to which the keyboard and mouse were connected. No issues with latency or input delay. My friend have been using this setup for a few days now and it works great.

Issues and Support

Found a bug or have a suggestion? Please feel free to create an issue on GitHub! I'm actively maintaining this project and would be happy to look into any problems or improvements you identify. While this is a personal project, I'm committed to helping others get it working and making it better.

Your feedback and contributions help make this project more reliable for everyone! 💜

References

License

This project is licensed under the MIT License - see the LICENSE file for details.