@jadonk jadonk released this Jan 23, 2019 · 0 commits to master since this release

Assets 6
  • Fixes USB network driver on some Windows 10 machines
  • Much newer Buildroot than previously built for all but GamePup
  • Uses u-boot environment stored at hard-coded location on MMC
  • Custom environment variable (fdtfile) for each image
  • Needs verification on Black and Black Wireless

@jadonk jadonk released this Jan 8, 2019 · 0 commits to master since this release

Assets 3

Serial number should be in the format of PC0100A4yywwnnnnnnnn

(Use proper version for A4)

  • Lights up both 7 segment displays
  • Plays tone on buzzer
  • Cycles through red, green and blue on RGB LED
  • Reads light sensor (prints over serial)
  • Reads accelerometer (prints over serial)
  • Writes serial number to EEPROM

At the end, it leaves the L button able to toggle the left 7 segment display and the R button to toggle the right 7 segment display.

This image requires you to manually replace the /boot/board.dtb link to am335x-pocketbeagle.dtb with a link to am335x-pocketbeagle-techlab.dtb.

@jadonk jadonk released this Nov 9, 2018 · 0 commits to master since this release

Assets 2

This image requires you to manually replace the /boot/board.dtb link to am335x-pocketbeagle.dtb with a link to am335x-pocketbeagle-gamepup.dtb.

https://builds.beagleboard.org/buildroot/beagle-tester/9e684febdf15ff879e04a6edda358ad9ee654026/buildroot-images-beagle-tester-9e684febdf15ff879e04a6edda358ad9ee654026.tgz

Pre-release
Pre-release

@jadonk jadonk released this Oct 24, 2018 · 3801 commits to beagle-tester since this release

Assets 4

@jadonk jadonk released this Oct 18, 2018 · 0 commits to master since this release

Assets 3

Not yet tested!

Also, make sure you use the SSID: BeagleBone-TESTER and PWD: BeagleBone for the wifi AP used under test.

@jadonk jadonk released this Oct 16, 2018 · 0 commits to master since this release

Assets 4
  • Ignore board type to assign first 12 bytes to EEPROM
  • Create separate images with symlinks to different board device trees

@jadonk jadonk released this Oct 15, 2018 · 3807 commits to beagle-tester since this release

Assets 3

sha256sum:
bd780386188b2e8d744b8bd95bebe6b1fa7b3ea38da25152e84d72075c06d7c0 beagle-tester-0.0.4.img.sz

@jadonk jadonk released this Oct 9, 2018 · 0 commits to master since this release

Assets 3

Changes

  • Add EEPROM header programming for BeagleBone Black
  • Add audio
  • Add a USB disk image with simple README.txt (Now Windows drive A:)
  • Include A15 / CEC 12MHz clock disable

Instructions

  1. Download https://github.com/beagleboard/buildroot/releases/download/bt-0.0.3/sdcard.img.xz
  2. Download https://etcher.io and use it to write the sdcard.img.xz to the microSD card
  3. Insert microSD and connect all cables except scanner and power
  4. Hold the S3/BOOT/SD button while applying power, then release the button when you see the power light
  5. Wait about 30 seconds for the penguin to show on the monitor and then connect the scanner and observe the test screen
  6. proceed with testing

@jadonk jadonk released this Oct 9, 2018 · 0 commits to master since this release

Assets 3

Disable the TDA19988 OSC IN. The device has its own internal oscillator.

Need to evaluate more the best way to configure this, but I verified this works for now.

See datasheet at https://media.digikey.com/pdf/Data%20Sheets/NXP%20PDFs/TDA19988_DS_21_july_2011.pdf

A release for production testing needs a full test log and general love, so don't grab this one for testing quite yet.

Write sdcard.img.xz to your microSD using etcher.io and hold BOOT when applying power to the board. See http://beagleboard.org/getting-started for more details.