#### Default Config file for BigTreeTech TFT Controllers
#
# BIGTREE_TFT35_V1_1 / BIGTREE_TFT35_V1_2    / BIGTREE_TFT35_V2_0
# BIGTREE_TFT35_V3_0 / BIGTREE_TFT35_E3_V3_0 / BIGTREE_TFT28_V1_0
# BIGTREE_TFT28_V3_0 / BIGTREE_TFT24_V1_1    / MKS_32_V1_4
#
# Firmware Source: https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware


#--------------------------------------------------------------------
# Supported Marlin Firmware Version
#--------------------------------------------------------------------
#  Minimum Marlin Firmware Version: 2.0.5.4
#  Distribution date: 2020-05-12
#  Source: https://github.com/MarlinFirmware/Marlin/releases
#

#  Note: Ensure that following options are enabled in Marlin firmware
#
#  M115_GEOMETRY_REPORT (in Configuration_adv.h)
#  REPORT_FAN_CHANGE (in Configuration_adv.h)
#  EMERGENCY_PARSER (in Configuration_adv.h)

#--------------------------------------------------------------------
# General Settings
#--------------------------------------------------------------------

#### UNIFIED MENU / CLASSIC MENU
# Select a UI Menu flavour
# Options: [Unified Menu: 1, Classic Menu: 0]
unified_menu:1

#### Baudrate
# Options: [2400: 0, 9600: 1, 19200: 2, 38400: 3, 57600: 4, 115200: 5, 250000: 6, 500000: 7, 1000000: 8]
baudrate:6

#### Default Touch Mode Language
# Select the language to display on the LCD while in Touch Mode.
# Options: [ENGLISH: 0,  CHINESE: 1,     RUSSIAN: 2,  JAPANESE: 3,    ARMENIAN: 4,
#            GERMAN: 5,    CZECH: 6,       SPAIN: 7,    FRENCH: 8,  PORTUGUESE: 9,
#           ITALIAN: 10,  POLISH: 11,     SLOVAK: 12,    DUTCH: 13,  HUNGARIAN: 14,
#           TURKISH: 15,   GREEK: 16,  SLOVENIAN: 17,  CATALAN: 18]
language:0

#### Default Touch Mode Color Options
# Options: [ WHITE: 0,  BLACK: 1,  RED: 2,  GREEN: 3,      BLUE: 4,       CYAN: 5,  MAGENTA: 6,    YELLOW: 7,
#           ORANGE: 8, PURPLE: 9, LIME: 10, BROWN: 11, DARKBLUE: 12, DARKGREEN: 13,    GRAY: 14, DARKGRAY: 15]
# Or set the color(RGB888 format) hex value directly(start with “0x”).
# Such as: 0xFF0000 : Red, 0x00FF00 : Green, 0x0000FF : Blue
# Title background color
title_back_color:1

# Background color
background_color:1

# Font foreground color
font_color:0

# Reminder font color, such as: "No print attached", "Busy processing", etc.
reminder_color:2

# Volume status/reminder font color, such as: "Card inserted", "Card removed"
volume_status_color:5

# Backgroud color for X Y Z position display in Status Screen.
status_xyz_bg_color:15

# List View Border Color
list_border_color:15

# List View button background color
list_button_bg_color:15

#### Rotate UI 180 degrees
# Options: [enable: 1, disable: 0]
rotate_ui:0

#### Show or hide Temperature ACK in Gcode Terminal
# Options: [Show: 1, Hide: 0]
terminal_ack:0

#### invert X axis button function in Move menu to match move buttons to actual axis
# Options: [enable: 1, disable: 0]
# Invert Axis format      [ X<option> Y<option> Z<option> E<option>]
invert_axis:X0 Y0 Z0

#### Persistent temperature info
# show persistent temperature info on all menu screens
# Options: [enable: 1, disable: 0]
persistent_info:0

#### File List Mode
# show file as list
# Options: [enable: 1, disable: 0]
files_list_mode:1

#### Notification style for ACK messages
# Set the notification style to use for displaying the ACK messages which start with 'echo:'
#
# NOTE: The OFF value is applied to any ACK message type (e.g. even to known echo ACK).
#       It means that any kind of ACK message is silently discard
#
# Options: [OFF: 0, POPUP: 1, TOAST: 2]
#   OFF:   No notification. The message is ignored.
#   POPUP: Display a popup window for user confirmation.
#   TOAST: A non-blocking Toast notification is displayed for few seconds. No user interaction is needed
ack_notification:1

#--------------------------------------------------------------------
# Marlin Mode Settings (Only for TFT24_V1.1 & TFT28/TFT35/TFT43/TFT50/TFT70_V3.0)
#--------------------------------------------------------------------

#### Default Mode
# Options: [0: Marlin Mode, 1: Touch Mode]
default_mode:1

#### Keep Serial Always ON
# Keep UART (Serial communication) alive in Marlin Mode
# Allow seamless OctoPrint UART connection to the TFT's UART/serial expansion port no matter which mode the TFT is in.
# Options: [0: Disabled, 1: Enabled]
serial_always_on:0

#### Default Marlin Mode Background & Font Color Options
# Options: [ WHITE: 0,  BLACK: 1,  RED: 2,  GREEN: 3,      BLUE: 4,       CYAN: 5,  MAGENTA: 6,    YELLOW: 7,
#           ORANGE: 8, PURPLE: 9, LIME: 10, BROWN: 11, DARKBLUE: 12, DARKGREEN: 13,    GRAY: 14, DARKGRAY: 15]
# Or set the color(RGB888 format) hex value directly(start with “0x”).
# Such as: 0xFF0000 : Red, 0x00FF00 : Green, 0x0000FF : Blue
marlin_bg_color:1
marlin_fn_color:8

#### Marlin Mode show title
# Options: [enable: 1, disable: 0]
marlin_show_title:1

# Run Marlin Mode in Fullscreen
# Options: [enable: 1, disable: 0] [Disabled. RECOMMENDED FOR TFT24]
marlin_fullscreen:0

# Select marlin type
# Options: [LCD12864: 1, LCD2004: 0]
marlin_type:1

#### Text displayed at the top of the TFT in Marlin Mode.
marlin_title:LCD12864 Simulator

#--------------------------------------------------------------------
# Printer / Machine Settings
#--------------------------------------------------------------------

#### Hotend Count
# Options: [1 to 6]
hotend_count:1

#### Enable heated Bed
# Options: [enable: 1, disable: 0]
heated_bed:1

#### Enable heated chamber
# The TFT will auto-detect if chamber heating is enabled in marlin firmware.
# Options: [enable: 1, disable: 0]
heated_chamber:0

#### Extruder Count
# Options: [1 to 6]
ext_count:1

#### Fan Count
# Options: [1 to 6]
fan_count:1

#### Fan Controller Count
# Options: 0 to 2
fan_ctrl_count:0

#### Bed / Extruder / Chamber Maximum Temperatures
# format [max_temp: T0:<max temp> T1:<max temp> T2:<max temp> T3:<max temp> T4:<max temp> T5:<max temp> BED:<max temp> CHAMBER:<max temp>]
max_temp:T0:275 T1:275 T2:275 T3:275 T4:275 T5:275 BED:150 CHAMBER:60

#### Cold Extrusion Minimum Temperature
min_temp:180

#### Fan Maximum PWM speed (0 to 255)
# format [fan_max: F0:<max PWM> F1:<max PWM> F2:<max PWM> F3:<max PWM> F4:<max PWM> F5:<max PWM> CtL:<max PWM> CtI:<max PWM>]
fan_max:F0:255 F1:255 F2:255 F3:255 F4:255 F5:255  CtL:255 CtI:255

#### Machine Size / Build Area (mm)
# The TFT will auto-detect the machine size in marlin firmware (Requires enabling `M115_GEOMETRY_REPORT`
# in Configuration_adv.h in Marlin firmware).
# Options: [X Axis: X, Y Axis: Y, Z Axis: Z]
# minimum possible value: -2000, maximum possible value: 2000
# minimum size limit format [size_min: X<minimum distance> Y<minimum distance> Z<minimum distance>]
# maximum size limit format [size_max: X<maximum distance> Y<maximum distance> Z<maximum distance>]
size_min:X0 Y0 Z0
size_max:X235 Y235 Z250

#### default Move Speeds (mm/min)
# Options: [Slow: S, Normal: N, Fast: F]
# format   [move_speed: S<feedrate mm/min> N<feedrate mm/min> F<feedrate mm/min>]
move_speed:S1000 N3000 F5000

#### default Extruder Speeds (mm/min)
# Options: [Slow: S, Normal: N, Fast: F]
# format   [ext_speed: S<feedrate mm/min> N<feedrate mm/min> F<feedrate mm/min>]
ext_speed:S60 N600 F1200

#### Auto Save Load Leveling Data
# The TFT will auto-detect if Auto Bed Level is available.
# Enable this will send "M500" after "G29" to store leveling value
# and send "M420 S1" to enable leveling state after startup
# Options: [enable: 1, disable: 0]
auto_load_leveling:1

#### Onboard / Printer SD Card Support
# On Marlin Firmware, The TFT will auto detect Onboard SD Card
# Auto-detect is not available for other firmwares like Smoothieware
# Options: [enable: 1, disable: 0, auto-detect: 2]
onboard_sd_support:2

#### M27 / Printing status refresh time (this will be used if SD_AUTOREPORT is not detected by the TFT)
M27_refresh_time:3

#### M27 always active - keep polling M27 even if not printing
# Options: [enable: 1, disable: 0]
M27_always_active:1

#### Long File Names Support
# On Marlin Firmware, The TFT will autodetect Long File Name supported
# Auto-detect is not available for other firmwares like Smoothieware
# Options: [enable: 1, disable: 0, auto-detect: 2]
long_filename_support:2

#### Show Fan Speed as Percentage
# Options: [enable: 1, disable: 0]
fan_speed_percent:1

#### Pause Settings
# position & Lengths in mm, Feedrates in mm/min
# minimum possible value: 0, maximum possible value: 2000
# Pause retract distance format [pause_retract: R<retract length> P<Resume Purge length>]
# Pause XY position format      [pause_pos: X<position in mm> Y<position in mm>]
# Pause Z raise format          [pause_z_raise: Z<distance in mm>]
# Pause feed Rate # format      [ X<feedrate mm/min> Y<feedrate mm/min> Z<feedrate mm/min> E<feedrate mm/min>]
pause_retract:R15 P16
pause_pos:X10 Y10
pause_z_raise:10
pause_feedrate:X6000 Y6000 Z6000 E600

### Manual Level Points Edge distance (mm)
# distance in mm, Feedrates in mm/min
# Leveling Edge distance format  [level_edge_distance: <distance from edge in mm>]
# Leveling Z Position format     [level_z_pos: Z<position in mm>]
# Leveling Z raise format        [level_z_raise: Z<distance in mm>]
# Leveling feed Rate format      [ X<feedrate mm/min> Y<feedrate mm/min> Z<feedrate mm/min>]
level_edge_distance:20
level_z_pos:0.2
level_z_raise:10
level_feedrate:X6000 Y6000 Z6000

#### Preheat Temperature
# Maximum Filament name length 7 characters
# format [T<hotend temp> B<bed temp>]
preheat_name1:PLA
preheat_temp1:T200 B60

preheat_name2:PETG
preheat_temp2:T240 B70

preheat_name3:ABS
preheat_temp3:T230 B90

preheat_name4:WOOD
preheat_temp4:T170 B50

preheat_name5:TPU
preheat_temp5:T220 B50

preheat_name6:NYLON
preheat_temp6:T250 B90

#--------------------------------------------------------------------
# Power Supply Settings (if connected to TFT Controller)
#--------------------------------------------------------------------

#### Default Power Supply Mode
# Options: [OFF: 0, ON: 1: Auto:2]
ps_on:0

#### Power Supply Active HIGH Settings
# Options: [HIGH: 1, LOW: 0]
ps_on_active_high:1

#### Maximum hot-end temperature of automatic shut down after printing (only if auto power is enabled)
# wait for the hot-end temperature to be lower than this value, then turn off the power automatically
auto_shutdown_temp:50

#--------------------------------------------------------------------
# Filament Runout Settings (if connected to TFT Controller)
#--------------------------------------------------------------------

#### Default FIlament Sensor
# Options: [NONE: 0, Normal: 1, SMART: 2]
fil_runout:0

#### Filament runout inverting - invert the logic of the sensor.
# Options: [true: 1, false: 0]
fil_runout_inverting:1

#### filament noise threshold  - Pause print when filament runout is detected for this time period in (ms).
# time duration in ms
fil_noise_threshold:100

#### Smart filament runout detection
# For use with an encoder disc that toggles runout pin as filament moves
fil_runout_distance:7

#--------------------------------------------------------------------
# Power Loss Recovery & BTT UPS Settings (if connected to TFT Controller)
#--------------------------------------------------------------------
#### Power Loss recovery default enable, disable to reduce the loss of SD card or U disk
# Options: [enable: 1, disable: 0]
pl_recovery_en:1

#### Home before Power Loss recovery
# Options: [enable: 1, disable: 0]
pl_recovery_home:0

#### Power Loss Z raise (mm)
# Raise Z axis on resume (on power loss with UPS)
pl_z_raise:10

#### Enable BTT UPS
# Options: [enable: 1, disable: 0]
btt_mini_ups:0


#--------------------------------------------------------------------
# Other device-specific settings
#--------------------------------------------------------------------

#### Sounds / Buzzer
# set sounds ON or OFF
#   touch_sound: enable/disable this to control touch feedback sound
#   toast_sound: enable/disable this to control all toast notification sounds
#   alert_sound: enable/disable this to control all popup and alert sounds
#                 like print finish alert, dialog sound etc.
# NOTE: Error messages from printer will always play the error sound.
# Options: [enable: 1, disable: 0]
touch_sound:1
toast_sound:1
alert_sound:1

#### Knob Led Color (only for TFT35 E3.0)
# Options: [LED_OFF: 0, LED_WHITE: 1, LED_RED: 2, LED_ORANGE: 3, LED_YELLOW: 4, LED_GREEN: 5, LED_BLUE: 6, LED_INDIGO: 7, LED_VIOLET: 8]
knob_led_color:0

#### Knob idle state
# Options: [true: 1, false: 0]
knob_led_idle:1

#### Default LCD Brightness levels (only for TFT35v3.0 & TFT28v3.0)
# Options: [(off) 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 (full)]
lcd_brightness:11
lcd_idle_brightness:5

#### Default LCD idle time (only for TFT35v3.0 & TFT28v3.0)
# Options [Off: 0, 5Sec: 1, 10Sec: 2, 30sec: 3, 1min: 4, 2min: 5, 5min: 6, 10min: 7]
lcd_idle_delay:4


#--------------------------------------------------------------------
# Custom G-Code Commands (up to 15 custom G-code)
#--------------------------------------------------------------------

#### To enable a custom Command:
# Remove '#' at the begining custom commands label & gcode.

#### To disable a custom Command:
# Add '#' at the begining custom commands label & gcode.

# if the values are left blank then default name and G-code will be used

# Options: [Label maximum length: 24 characters, G-code Maximum length 70 characters]

custom_label_1:Disable steppers
custom_gcode_1:M84\n
custom_label_2:Init sd card
custom_gcode_2:M21\n
custom_label_3:Release sd card
custom_gcode_3:M22\n
custom_label_4:Restore leveling
custom_gcode_4:M420 S1\n
custom_label_5:Save to EEPROM
custom_gcode_5:M500\n
custom_label_6:Restore from EEPROM
custom_gcode_6:M501\n
custom_label_7:EEPROM defaults
custom_gcode_7:M502\n
#custom_label_8:custom8
#custom_gcode_8:M105\n
#custom_label_9:custom9
#custom_gcode_9:M105\n
#custom_label_10:custom10
#custom_gcode_10:M105\n
#custom_label_11:custom11
#custom_gcode_11:M105\n
#custom_label_12:custom12
#custom_gcode_12:M105\n
#custom_label_13:custom13
#custom_gcode_13:M105\n
#custom_label_14:custom14
#custom_gcode_14:M105\n
#custom_label_15:custom15
#custom_gcode_15:M105\n

#--------------------------------------------------------------------
# Start, End & Cancel G-codes
#--------------------------------------------------------------------

#### Default Start Gcode Status
# Options: [enable: 1, disable: 0]
start_gcode_enabled:0

#### Default End Gcode Status
# Options: [enable: 1, disable: 0]
end_gcode_enabled:0

#### Default Cancel Gcode Status
# Options: [enable: 1, disable: 0]
cancel_gcode_enabled:0

#### Start G-code - run this G-code before starting print
# maximum length 50 characters
start_gcode:G28 XY R20\n

#### End G-code - run this G-code after finishing print
# maximum length 50 characters
end_gcode:M104 S0\nM140 S0\nM18\n

#### Cancel G-code - run this G-code after canceling print
# maximum length 50 characters
cancel_gcode:M104 S0\nM140 S0\nG28 XY R10\n