Permalink
Commits on Nov 3, 2011
  1. made it possible to have an intermediate M92 command without the extr…

    …uder motor running wild.
    committed Nov 3, 2011
  2. trying just PI instead of PID

    committed Nov 3, 2011
  3. float should be sufficient.

    committed Nov 3, 2011
Commits on Nov 2, 2011
  1. PID-I was a bit too low.

    committed Nov 2, 2011
  2. a bit higher even.

    committed Nov 2, 2011
  3. PID now working. Actually, its more than pid, lets call it PIDC. Addi…

    …tionnally to the P, I, and D term I use a term that is proportional to the extruder motor speed. If its running faster, one expects that more heat is needed, due to the additional melting.
    committed Nov 2, 2011
Commits on Nov 1, 2011
  1. display update bug

    committed Nov 1, 2011
  2. next try.

    committed Nov 1, 2011
  3. disabled lcd for most users

    committed Nov 1, 2011
  4. Merge branch 'master' of https://github.com/bkubicek/Marlin

    Conflicts:
    	Marlin/Configuration.h
    committed Nov 1, 2011
  5. better PID values.

    added M220 S<percent>velocity factor override
    committed Nov 1, 2011
Commits on Oct 30, 2011
Commits on Oct 26, 2011
  1. enable watchdog with manual reset (still untested, but doing at least…

    … no harm) and adding some reasonable pid settings. Tested without actually printing.
    committed Oct 26, 2011
  2. fix minimum feedrate

    committed Oct 26, 2011
Commits on Oct 24, 2011
Commits on Oct 23, 2011
  1. updates full for lcd

    committed Oct 23, 2011
Commits on Oct 21, 2011
  1. added fan control into menu

    committed Oct 21, 2011
  2. now there is pid enabled by defualt

    Merge branch 'Slowdown' of https://github.com/bkubicek/Marlin
    
    Conflicts:
    	Marlin/EEPROM.h
    	Marlin/Marlin.pde
    committed Oct 21, 2011
  3. enable beep again

    committed Oct 21, 2011
  4. SD card autodetect added.

    committed Oct 21, 2011
  5. found the bug in the new panels. Pullup on output pins instead of inp…

    …ut pins on switch/encoder stuff.
    committed Oct 21, 2011
Commits on Oct 18, 2011
  1. Echo PID settings

    lampmaker committed Oct 18, 2011
  2. fixed typo

    lampmaker committed Oct 18, 2011
  3. Included Streaming lib; added ECHO

    ECHO outputs serial data with "echo:" attached in front of it.   This allows you to send data to replicatorg witout causing error messages.  Debugging level needs to be set to "INFO" in repg.
    
    Using the streaming lib, messages can be sent like this:
    
    ECHO ("Maximum feedrate "<<_FLOAT(max_feedrate,2))
    
     will output "echo: Maximum feedrate 300.00"
    
    ECHOLN(x) is the same as ECHO, but adds a linebreak after.
    lampmaker committed Oct 18, 2011
Commits on Oct 16, 2011
  1. ; fixed

    committed Oct 16, 2011
Commits on Oct 15, 2011
  1. better default values

    committed Oct 15, 2011
  2. sane config

    committed Oct 15, 2011
  3. Merge branch 'master' of https://github.com/bkubicek/Marlin

    Conflicts:
    	Marlin/EEPROM.h
    committed Oct 15, 2011