timer.c

#include	"timer.h"

#include	<avr/interrupt.h>

#include	"arduino.h"
#include	"config.h"

#ifdef	HOST
#include	"dda_queue.h"
#endif

/*
	how often we overflow and update our clock; with F_CPU=16MHz, max is < 4.096ms (TICK_TIME = 65535)
*/
#define		TICK_TIME			2 MS
#define		TICK_TIME_MS	(TICK_TIME / (F_CPU / 1000))

volatile uint32_t	next_step_time;

uint8_t						clock_counter_10ms = 0;
uint8_t						clock_counter_250ms = 0;
uint8_t						clock_counter_1s = 0;
volatile uint8_t	clock_flag = 0;

// comparator B is the "clock", happens every TICK_TIME
ISR(TIMER1_COMPB_vect) {
	// set output compare register to the next clock tick
	OCR1B = (OCR1B + TICK_TIME) & 0xFFFF;
	
	/*
	clock stuff
	*/
	clock_counter_10ms += TICK_TIME_MS;
	if (clock_counter_10ms >= 10) {
		clock_counter_10ms -= 10;
		clock_flag |= CLOCK_FLAG_10MS;
		
		clock_counter_250ms += 1;
		if (clock_counter_250ms >= 25) {
			clock_counter_250ms -= 25;
			clock_flag |= CLOCK_FLAG_250MS;
			
			clock_counter_1s += 1;
			if (clock_counter_1s >= 4) {
				clock_counter_1s -= 4;
				clock_flag |= CLOCK_FLAG_1S;
			}
		}
	}
}

#ifdef	HOST
void timer1_compa_isr(void) __attribute__ ((hot));
void timer1_compa_isr() {
	// led on
	WRITE(SCK, 1);
	
	// disable this interrupt. if we set a new timeout, it will be re-enabled when appropriate
	TIMSK1 &= ~MASK(OCIE1A);
	
	// stepper tick
	queue_step();
	
	// led off
	WRITE(SCK, 0);
}

// comparator A is the step timer. It has higher priority then B.
ISR(TIMER1_COMPA_vect) {
	// Check if this is a real step, or just a next_step_time "overflow"
	if (next_step_time < 65536) {
		next_step_time = 0;
		// step!
		timer1_compa_isr();
		return;
	}
	
	next_step_time -= 65536;

	// similar algorithm as described in setTimer below.
	if (next_step_time < 65536) {
		OCR1A = (OCR1A + next_step_time) & 0xFFFF;
	} else if(next_step_time < 75536){
		OCR1A = (OCR1A - 10000) & 0xFFFF;
		next_step_time += 10000;
	}
	// leave OCR1A as it was
}
#endif /* ifdef HOST */

void timer_init()
{
	// no outputs
	TCCR1A = 0;
	// Normal Mode
	TCCR1B |= MASK(CS10);
	// set up "clock" comparator for first tick
	OCR1B = TICK_TIME & 0xFFFF;
	// enable interrupt
	TIMSK1 |= MASK(OCIE1B);
}

#ifdef	HOST
void setTimer(uint32_t delay)
{
	// save interrupt flag
	uint8_t sreg = SREG;
	uint16_t step_start = 0;
	// disable interrupts
	cli();

	// re-enable clock interrupt in case we're recovering from emergency stop
	TIMSK1 |= MASK(OCIE1B);
	
	if (delay > 0) {
		if (delay <= 16) {
			// unfortunately, force registers don't trigger an interrupt, so we do the following
			// "fire" ISR- maybe it sets a new timeout
			timer1_compa_isr();
		}
		else {
			// Assume all steps belong to one move. Within one move the delay is 
			// from one step to the next one, which should be more or less the same
			// as from one step interrupt to the next one. The last step interrupt happend
			// at OCR1A, so start delay from there.
			step_start = OCR1A;
			if (next_step_time == 0) {
				// new move, take current time as start value
				step_start = TCNT1;
			}

			next_step_time = delay;
			if (next_step_time < 65536) {
				// set the comparator directly to the next real step
				OCR1A = (next_step_time + step_start) & 0xFFFF;
			}
			else if (next_step_time < 75536) {
				// Next comparator interrupt would have to trigger another
				// interrupt within a short time (possibly within 1 cycle).
				// Avoid the impossible by firing the interrupt earlier.
				OCR1A = (step_start - 10000) & 0xFFFF;
				next_step_time += 10000;
			}
			else {
				OCR1A = step_start;
			}
			
			TIMSK1 |= MASK(OCIE1A);
		}
	} else {
		// flag: move has ended
		next_step_time = 0;
		TIMSK1 &= ~MASK(OCIE1A);
	}
	
	// restore interrupt flag
	SREG = sreg;
}

void timer_stop() {
	// disable all interrupts
	TIMSK1 = 0;
}
#endif /* ifdef HOST */