Skip to content

HTTPS clone URL

Subversion checkout URL

You can clone with HTTPS or Subversion.

Download ZIP
Fetching contributors…

Cannot retrieve contributors at this time

122 lines (118 sloc) 4.482 kb
/* Arduino SdFat Library
* Copyright (C) 2009 by William Greiman
*
* This file is part of the Arduino SdFat Library
*
* This Library is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This Library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with the Arduino SdFat Library. If not, see
* <http://www.gnu.org/licenses/>.
*/
/**
* \file
* \brief configuration definitions
*/
#include "Marlin.h"
#ifdef SDSUPPORT
#ifndef SdFatConfig_h
#define SdFatConfig_h
#include <stdint.h>
//------------------------------------------------------------------------------
/**
* To use multiple SD cards set USE_MULTIPLE_CARDS nonzero.
*
* Using multiple cards costs 400 - 500 bytes of flash.
*
* Each card requires about 550 bytes of SRAM so use of a Mega is recommended.
*/
#define USE_MULTIPLE_CARDS 0
//------------------------------------------------------------------------------
/**
* Call flush for endl if ENDL_CALLS_FLUSH is nonzero
*
* The standard for iostreams is to call flush. This is very costly for
* SdFat. Each call to flush causes 2048 bytes of I/O to the SD.
*
* SdFat has a single 512 byte buffer for SD I/O so it must write the current
* data block to the SD, read the directory block from the SD, update the
* directory entry, write the directory block to the SD and read the data
* block back into the buffer.
*
* The SD flash memory controller is not designed for this many rewrites
* so performance may be reduced by more than a factor of 100.
*
* If ENDL_CALLS_FLUSH is zero, you must call flush and/or close to force
* all data to be written to the SD.
*/
#define ENDL_CALLS_FLUSH 0
//------------------------------------------------------------------------------
/**
* Allow use of deprecated functions if ALLOW_DEPRECATED_FUNCTIONS is nonzero
*/
#define ALLOW_DEPRECATED_FUNCTIONS 1
//------------------------------------------------------------------------------
/**
* Allow FAT12 volumes if FAT12_SUPPORT is nonzero.
* FAT12 has not been well tested.
*/
#define FAT12_SUPPORT 0
//------------------------------------------------------------------------------
/**
* SPI init rate for SD initialization commands. Must be 5 (F_CPU/64)
* or 6 (F_CPU/128).
*/
#define SPI_SD_INIT_RATE 5
//------------------------------------------------------------------------------
/**
* Set the SS pin high for hardware SPI. If SS is chip select for another SPI
* device this will disable that device during the SD init phase.
*/
#define SET_SPI_SS_HIGH 1
//------------------------------------------------------------------------------
/**
* Define MEGA_SOFT_SPI nonzero to use software SPI on Mega Arduinos.
* Pins used are SS 10, MOSI 11, MISO 12, and SCK 13.
*
* MEGA_SOFT_SPI allows an unmodified Adafruit GPS Shield to be used
* on Mega Arduinos. Software SPI works well with GPS Shield V1.1
* but many SD cards will fail with GPS Shield V1.0.
*/
#define MEGA_SOFT_SPI 0
//------------------------------------------------------------------------------
/**
* Set USE_SOFTWARE_SPI nonzero to always use software SPI.
*/
#define USE_SOFTWARE_SPI 0
// define software SPI pins so Mega can use unmodified 168/328 shields
/** Software SPI chip select pin for the SD */
uint8_t const SOFT_SPI_CS_PIN = 10;
/** Software SPI Master Out Slave In pin */
uint8_t const SOFT_SPI_MOSI_PIN = 11;
/** Software SPI Master In Slave Out pin */
uint8_t const SOFT_SPI_MISO_PIN = 12;
/** Software SPI Clock pin */
uint8_t const SOFT_SPI_SCK_PIN = 13;
//------------------------------------------------------------------------------
/**
* The __cxa_pure_virtual function is an error handler that is invoked when
* a pure virtual function is called.
*/
#define USE_CXA_PURE_VIRTUAL 1
/**
* Defines for long (vfat) filenames
*/
/** Number of VFAT entries used. Every entry has 13 UTF-16 characters */
#define MAX_VFAT_ENTRIES (2)
/** Total size of the buffer used to store the long filenames */
#define LONG_FILENAME_LENGTH (13*MAX_VFAT_ENTRIES+1)
#endif // SdFatConfig_h
#endif
Jump to Line
Something went wrong with that request. Please try again.