BauerCam v1.13 (Forge 1.12 and 1.12.1)

• Automatically switches to linear interpolation if you only use 2 points, closes #4 (e.g. dolly zoom is now a lot easier to do)
• Transition from sending "/tp" to direct local world integrated server sync
  • Fixes the "/cam goto", "/cam replace" workflow, (Camera angles were previously normalized due to "/tp" resulting in unwanted barrel rolls) closes #3
  • Supersedes having to open the LAN server with cheats enabled
• Warning messages are now colored

Compatible with Forge 1.12 and 1.12.1

BauerCam v1.12 (Forge 1.12)

Update to 1.12

BauerCam v1.12 (Forge 1.11 and 1.11.2)

Update to 1.11 and 1.11.2

BauerCam v1.12 (Forge 1.10.2)

Preview rendering:

Better performance:

• Interpolated points for preview rendering will now be cached
• Amount of interpolated points is now dynamically determined based on the distances between all points

Bug fixes:

• Uses GLStateManager for most of the rendering now: Rendering should be a bit more compatible with Minecraft.
• Eye height of the rendering position is now used
• Known bug: Using shaders together with VBOs on makes the preview disappear (Needs further investigation)

Changes:

• Preview path is now doubled in thickness

Other changes:

• Added a low german translation
• Warn the player that a focus is still being set when clearing the path

BauerCam v1.11 (Forge 1.10.2)

Preview rendering:

Paths will now be rendered with red lines until you start them. This is useful if you craft an eye-pleasing camera path first and finish your film set afterwards.
Disable/enable with "/cam preview"

BauerCam v1.10 (Forge 1.10.2)

Importing/Exporting:

• "/cam export" and "/cam import" have been renamed to "/cam save" and "/cam load"
• Already existing saved files will not be overwritten now
• The whole filepath to the file is now shown upon saving. This is quite useful if you are using a Launcher which does not require any interaction with the install folder and you do not have a clue where it is.

More precise path control:

"/cam remove" and "/cam insert" have been added. This allows for much better correction of the path now if you mess up.

Circular paths:

• Using "/cam circle" will automatically create path points which behave like a circle
• left/right movement is meant for targets being set inside the circle. A target outside of the circle swaps the logic.

BauerCam v1.9 (Forge 1.10.2)

FOV changing:

• The camera path will now allow dynamic FOV changes by remembering your current FOV setting when setting points
• Or you adjust the FOV setting via the keys O, (Higher) I, (Reset to 70) and U (Lower)
• With those keys you can adjust the FOV beyond the minecraft limits: 5 - 150
• FOV changing is useful for Dolly Zoom effects (be careful with anything else as it can make some people motion sick)
• Due to this new property exported files from v1.8 and below are now incompatible! (Without fixing them by hand)

Target/Focus:

• Use "/cam target set" to set a point where your whole camera path will then be focused to.
• Use "/cam target off" to remove the target point.

Targets will not be saved to exported files.

Internal changes:

• Heavy refactoring for the interpolation section of the code to make it more modular for future additions. (Circular paths are planned)
• Vector math added for targets (will also be useful for circular paths)

BauerCam v1.8 (Forge 1.10.2)

Fixed unstable/jumping camera movement that only some users experienced
Update still highly recommended for all users

BauerCam v1.7 (Forge 1.8.9)

All new features and bugfixes have been backported to 1.8.9.

This release does contain the Coremod again for Optifine compatibility which was not necessary for newer minecraft versions.

BauerCam v1.7 (Forge 1.9.4 & 1.10.2)

Cosmetic changes and some potential bug fixes

Attached source code comes from master (1.10.2) but is completely the same for 1.9.4 (just minecraft target versions have to be changed)