DDF for Sonoff TRVZB Thermostat by fox34 · Pull Request #7357 · dresden-elektronik/deconz-rest-plugin

fox34 · 2023-11-15T16:13:49Z

As discussed in #7334. Thank you @Smanar!

Product name : TRVZB
Manufacturer : SONOFF
Model identifier : TRVZB

SwoopX

Hi there,

I'm afraid, the DDF requires some significant changes to be considered. The suggested file would be barely functional.

SwoopX · 2023-12-11T22:14:30Z

+        {
+          "name": "attr/uniqueid"
+        },
+        {


The battery reading and checkin is missing:

{ "name": "config/battery", "awake": true, "parse": { "at": "0x0021", "cl": "0x0001", "ep": 1, "eval": "Item.val = Attr.val / 2;", "fn": "zcl:attr" }, "read": { "fn": "none" } }, { "name": "config/checkin", },

SwoopX · 2023-12-11T22:18:44Z

+          "name": "state/lastupdated"
+        },
+        {
+          "name": "state/temperature"


The defaults for this item are tailored for temperature measurement sensors and hence, will not work here. Please replace it by the following:

"name": "state/temperature", "refresh.interval": 3660, "parse": { "at": "0x0000", "cl": "0x0201", "ep": 1, "eval": "Item.val = Attr.val;", "fn": "zcl:attr" }, "read": { "at": "0x0000", "cl": "0x0201", "ep": 1, "fn": "zcl:attr" }

SwoopX · 2023-12-11T22:20:20Z

+      ]
+    }
+  ],
+  "bindings": [


The battery binding is missing:

{ "bind": "unicast", "src.ep": 1, "dst.ep": 1, "cl": "0x0001", "report": [ { "at": "0x0021", "dt": "0x20", "min": 3600, "max": 43200, "change": "0x00000002" } ] },

SwoopX · 2023-12-11T22:27:49Z

+          "min": 30,
+          "max": 360,
+          "change": "0x0000000A"
+        }


Please add additional thermostat bindings

{ "at": "0x0012", "dt": "0x29", "min": 1, "max": 3600, "change": "0x00000001" }, { "at": "0x001C", "dt": "0x30", "min": 1, "max": 3600 }

SwoopX · 2023-12-11T22:28:08Z

+          "min": 30,
+          "max": 360,
+          "change": "0x0000000A"


Please change the values to:

"min": 60, "max": 300, "change": "0x00000064"

SwoopX · 2023-12-11T22:29:56Z

+        {
+          "name": "state/on"
+        },


This item is not supported, so please remove.

SwoopX · 2023-12-11T22:31:08Z

+        {
+          "name": "config/mode"
+        },


Please investigate which modes are supported by the device. The code below must be amended according to the findings:

{ "name": "config/mode", "refresh.interval": 3660, "read": { "at": "0x001C", "cl": "0x0201", "ep": 1, "fn": "zcl:attr" }, "parse": { "at": "0x001C", "cl": "0x0201", "ep": 1, "eval": "if (Attr.val == 0) { Item.val = 'off' } else if (Attr.val == 1) { Item.val = 'auto' } else if (Attr.val == 4) { Item.val = 'heat' };", "fn": "zcl:attr" }, "write": { "at": "0x001C", "cl": "0x0201", "dt": "0x10", "ep": 1, "eval": "if (Item.val == 'off') { 0 } else if (Item.val == 'auto') { 1 } else if (Item.val == 'heat') { 4 };", "fn": "zcl:attr" }, "default": "heat" },

SwoopX · 2023-12-11T22:33:00Z

+          "0x0000",
+          "0x0201"
+        ]
+      },


In order to make use of the config/mode item, the following code must be added and contain the actually usable settings (see respetive item comment)

"meta": { "values": { "config/mode": {"off": 0, "auto": 1, "heat": 4} } },

SwoopX · 2023-12-11T22:34:35Z

+        },
+        {
+          "name": "config/heatsetpoint",
+          "default": 0


Please remove the default value and add "refresh.interval": 3660 instead.

SwoopX · 2023-12-11T22:38:11Z

+        {
+          "name": "config/offset",
+          "default": 0
+        },


Please replace by the code below:

{ "name": "config/offset", "refresh.interval": 3660, "read": { "at": "0x0010", "cl": "0x0201", "ep": 1, "fn": "zcl:attr" }, "parse": { "at": "0x0010", "cl": "0x0201", "ep": 1, "eval": "Item.val = Attr.val * 10;", "fn": "zcl:attr" }, "write": { "at": "0x0010", "cl": "0x0201", "dt": "0x28", "ep": 1, "eval": "Item.val / 10;", "fn": "zcl:attr" }, "range": [-250, 250], "default": 0 },

Smanar · 2024-01-10T16:50:55Z

@fox34 are you still here ?

fox34 · 2024-01-10T20:02:04Z

I made the requested changes, however:

Please investigate which modes are supported by the device.

How would I do this? The device can be toggled between automatic and manual operation (and turned off, obviously). Automatic mode can (only?) be configured in the "official" SONOFF app, which I cannot use because I do not own the SONOFF gateway.

Smanar · 2024-01-11T16:18:55Z

How would I do this? The device can be toggled between automatic and manual operation (and turned off, obviously). Automatic mode can (only?) be configured in the "official" SONOFF app, which I cannot use because I do not own the SONOFF gateway.

Yes, it's fine, just check wich one mode you can use on it.
From Z2M they are using same

.withSystemMode(['off', 'auto', 'heat'], ea.ALL, 'Mode of the thermostat')

And they have too problem with the "auto" mode, it seem this device don't use zigbee classic request, and use instead a personnal one > Koenkk/zigbee-herdsman-converters#6443

And BTW, they have too found some others request on the special cluster, for exemple can try


                {
                    "name": "config/locked",
                    "read": {
                        "at": "0x0000",
                        "cl": "0xFC11",
                        "ep": 1,
                        "fn": "zcl:attr"
                    },
                    "write": {
                        "at": "0x0000",
                        "cl": "0xFC11",
                        "dt": "0x30",
                        "ep": 1,
                        "eval": "Item.val ? 1 : 0;",
                        "fn": "zcl:attr"
                    },
                    "parse": {
                        "at": "0x0000",
                        "cl": "0xFC11",
                        "ep": 1,
                        "eval": "Item.val = Attr.val",
                        "fn": "zcl:attr"
                    },
                    "default": false,
                    "refresh.interval": 84000
                },

for the lock/unlock

SwoopX

Looks ok for me wrt the requested changes, thanks!

manup · 2024-02-05T01:10:00Z

So ready for merging? :)

Smanar · 2024-02-05T16:48:35Z

For me yes, have checked again ,all @SwoopX remark are resolved.

coives · 2024-03-14T10:49:51Z

When merging?

Add support for SONOFF TRVZB Thermostat

35b0030

fox34 mentioned this pull request Nov 15, 2023

Device Request: SONOFF TRVZB Thermostat #7334

Closed

1 task done

SwoopX added the Device Request label Dec 11, 2023

SwoopX linked an issue Dec 11, 2023 that may be closed by this pull request

Device Request: SONOFF TRVZB Thermostat #7334

Closed

1 task done

SwoopX requested changes Dec 11, 2023

View reviewed changes

Sonoff TRVZB: Requested changes

05abe4d

fix surplus comma

a5fd85f

fox34 requested a review from SwoopX January 11, 2024 08:44

SwoopX approved these changes Jan 14, 2024

View reviewed changes

SwoopX added this to the v2.27.0-beta milestone Mar 21, 2024

manup merged commit 5e399d1 into dresden-elektronik:master Mar 28, 2024

manup changed the title ~~DDF for SONOFF TRVZB Thermostat~~ DDF for Sonoff TRVZB Thermostat Mar 28, 2024

fox34 deleted the sonoff-trvzb branch November 19, 2024 08:06

Conversation

fox34 commented Nov 15, 2023 • edited Loading Uh oh! There was an error while loading. Please reload this page.

Uh oh!

Uh oh!

SwoopX left a comment

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Choose a reason for hiding this comment

Uh oh!

Smanar commented Jan 10, 2024

Uh oh!

fox34 commented Jan 10, 2024

Uh oh!

Smanar commented Jan 11, 2024 • edited Loading Uh oh! There was an error while loading. Please reload this page.

Uh oh!

Uh oh!

SwoopX left a comment

Choose a reason for hiding this comment

Uh oh!

manup commented Feb 5, 2024

Uh oh!

Smanar commented Feb 5, 2024

Uh oh!

coives commented Mar 14, 2024

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

5 participants

fox34 commented Nov 15, 2023 •

edited

Loading

Smanar commented Jan 11, 2024 •

edited

Loading