Skip to content
Commits on Mar 1, 2014
  1. Set XYZ origin to center of platform, tweak speed / accel / jerk valu…

    …es, increase Z home backoff
    Ed Nisley committed Mar 1, 2014
Commits on Dec 11, 2013
  1. Clear all motor directions

    Set preheat constants
    Enable EEPROM storage
    committed Dec 11, 2013
Commits on Dec 10, 2013
Commits on Dec 9, 2013
  1. Add Panucatt Devices Azteeg X3 with thermocouple inputs

    Add thermocouple amp type selection for AD595 and AD849[4567], with proper default gains
    committed Dec 9, 2013
Commits on Dec 7, 2013
  1. @ErikZalm

    Merge pull request #675 from forrestg/master

    Added support for Cheaptronic v1 electronic
    ErikZalm committed Dec 7, 2013
  2. @forrestg
Commits on Nov 28, 2013
  1. @alexborro

    Bed Heater monitoring in Controller Fan

    In some cases the Bed Heater FET heats up more then stepper drivers, so
    this change add the bed monitoring to the controller fan. As soon as the
    bed heater is turned on, the controller fan will run as well.
    alexborro committed Nov 27, 2013
  2. @alexborro

    Z Axis Safe Homing when using Z Probe

    Recommended for those who are using the Z Probe for Z Homing (as
    Z-Endstop)
    
    This feature has two changes:
    
    1) Allow user to choose where the Z Probe will touch the bed when homing
    all axis together (G28) by setting below defines:
    
    Z_SAFE_HOMING_X_POINT
    Z_SAFE_HOMING_Y_POINT
    
    2) Prevents the user to perform Z Axis Homing when the Z Probe is
    outsite bed.
    alexborro committed Nov 27, 2013
Commits on Nov 27, 2013
  1. @alexborro

    Allow heaters to stay full On when PWM=127

    In previous version, even with PWM = 127, the system turns the FET off
    and then on in the next cycle. This bevavior may increase the FET heat
    dissipation.
    It was fixed keeping the FET always On when PWM=127.
    alexborro committed Nov 27, 2013
Commits on Nov 17, 2013
  1. @ErikZalm

    Changed slow buttons behavior.

    ErikZalm committed Nov 17, 2013
  2. @ErikZalm

    Added HEATERS_PARALLEL (Request from reifsnyderb)

    This allows a hot end with two heaters and a FET for each heater. This is useful if the FET is not capable of heating two heaters.
    ErikZalm committed Nov 17, 2013
Commits on Nov 10, 2013
  1. @ErikZalm
  2. @ErikZalm

    Merge pull request #647 from shaggythesheep/newfeature-M226

    Implement M226 - GCode Initiated Pause
    ErikZalm committed Nov 10, 2013
  3. @ErikZalm

    Merge pull request #641 from hugokernel/master

    M80 - ATX Power On related modification
    ErikZalm committed Nov 10, 2013
  4. @ErikZalm

    Merge pull request #640 from fmalpartida/SAV-MkI

    Added support for BT on AT90USB devices, corrected LCD bug, added new board and LCD
    ErikZalm committed Nov 10, 2013
  5. @ErikZalm

    Merge pull request #637 from justuswilhelm/Marlin_v1

    Fix servo control for Melzi v2.0
    ErikZalm committed Nov 10, 2013
  6. @ErikZalm

    Merge pull request #636 from PrintToPeer/Marlin_v1

    Add UUID support to M115 responses.
    ErikZalm committed Nov 10, 2013
  7. @ErikZalm

    Merge pull request #635 from dbenamy/Marlin_v1

    Add (correct) missing pin definitions for Y2
    ErikZalm committed Nov 10, 2013
Commits on Nov 9, 2013
  1. Implement M226 - GCode Initiated Pause

    Implemented M226 as described here:
    http://reprap.org/wiki/G-code#M226:_Gcode_Initiated_Pause
    
    Waits for pin to be become either HIGH, LOW or the inverse of what it
    was before. Allows printing to pause until user interaction
    Richard Miles committed Nov 9, 2013
Commits on Nov 4, 2013
  1. If you have a switch on suicide pin, this is useful if you want to

    start another print with suicide feature after a print without
    suicide...
    Charles R committed Nov 4, 2013
Commits on Nov 3, 2013
  1. @fmalpartida

    Added BT support on AT90USB devices

    Added AT90USB device BT connectivity support using second UART.
    fmalpartida committed Nov 3, 2013
Commits on Nov 1, 2013
  1. @KazW
Commits on Oct 31, 2013
  1. @dbenamy

    Add (correct) missing pin definitions for Y2

    I tested this and it works.
    dbenamy committed Oct 30, 2013
Commits on Oct 30, 2013
  1. @fmalpartida

    Corrected LCD only error

    If only an LCD is defined and no menu or keyboard defined, there is a
    compilation error.
    
    Added conditional compilation.
    fmalpartida committed Oct 30, 2013
  2. Fix servo control for Melzi

    Justus Perlwitz committed Oct 30, 2013
  3. @ErikZalm

    Merge pull request #632 from dbenamy/Marlin_v1

    Made instructions more clear.
    ErikZalm committed Oct 30, 2013
  4. @dbenamy

    Made instructions more clear.

    Not sure what happened to my last commit so this includes that one + reordering the steps.
    dbenamy committed Oct 30, 2013
  5. @fmalpartida

    Initial SAV MkI (RepRap CloneWars board) integration.

    Included support for BT dongle on AT90USB boards.
    Added LCD Shift Register LCD control
    Included support for RepRap Clone Wars project board (SAV MKI).
    fmalpartida committed Oct 30, 2013
Commits on Oct 29, 2013
  1. @ErikZalm

    Merge pull request #630 from dumle29/Marlin_v1

    PS_ON configurable boot state
    ErikZalm committed Oct 29, 2013
  2. @dumle29

    PS_ON configurable boot state

    Allows the user to select wheter or not the PSU should be turned on or
    kept in standby when marlin boots
    dumle29 committed Oct 29, 2013
Commits on Oct 25, 2013
  1. @bkubicek

    Merge pull request #629 from whosawhatsis/Marlin_v1

    Make G11 not horribly broken
    bkubicek committed Oct 24, 2013
  2. @whosawhatsis
Commits on Oct 22, 2013
  1. @alexborro
  2. Fix '#'

    since it can occure in comments.
    bkubicek committed Oct 22, 2013
Something went wrong with that request. Please try again.