update nl80211.h

nl80211.h

@@ -804,6 +804,30 @@ enum nl80211_commands {
  * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
  *	means support for per-station GTKs.
  *
+ * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting.
+ *	This can be used to mask out antennas which are not attached or should
+ *	not be used for transmitting. If an antenna is not selected in this
+ *	bitmap the hardware is not allowed to transmit on this antenna.
+ *
+ *	Each bit represents one antenna, starting with antenna 1 at the first
+ *	bit. Depending on which antennas are selected in the bitmap, 802.11n
+ *	drivers can derive which chainmasks to use (if all antennas belonging to
+ *	a particular chain are disabled this chain should be disabled) and if
+ *	a chain has diversity antennas wether diversity should be used or not.
+ *	HT capabilities (STBC, TX Beamforming, Antenna selection) can be
+ *	derived from the available chains after applying the antenna mask.
+ *	Non-802.11n drivers can derive wether to use diversity or not.
+ *	Drivers may reject configurations or RX/TX mask combinations they cannot
+ *	support by returning -EINVAL.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving.
+ *	This can be used to mask out antennas which are not attached or should
+ *	not be used for receiving. If an antenna is not selected in this bitmap
+ *	the hardware should not be configured to receive on this antenna.
+ *	For a more detailed descripton see @NL80211_ATTR_WIPHY_ANTENNA_TX.
+ *
+ * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -973,6 +997,11 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_SUPPORT_IBSS_RSN,
 
+	NL80211_ATTR_WIPHY_ANTENNA_TX,
+	NL80211_ATTR_WIPHY_ANTENNA_RX,
+
+	NL80211_ATTR_MCAST_RATE,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -1132,6 +1161,7 @@ enum nl80211_rate_info {
  * @__NL80211_STA_INFO_AFTER_LAST: internal
  * @NL80211_STA_INFO_MAX: highest possible station info attribute
  * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
+ * @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm)
  * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
  * 	containing info as possible, see &enum nl80211_sta_info_txrate.
  * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
@@ -1149,6 +1179,7 @@ enum nl80211_sta_info {
 	NL80211_STA_INFO_PLID,
 	NL80211_STA_INFO_PLINK_STATE,
 	NL80211_STA_INFO_SIGNAL,
+	NL80211_STA_INFO_SIGNAL_AVG,
 	NL80211_STA_INFO_TX_BITRATE,
 	NL80211_STA_INFO_RX_PACKETS,
 	NL80211_STA_INFO_TX_PACKETS,
@@ -1307,7 +1338,11 @@ enum nl80211_bitrate_attr {
  * 	wireless core it thinks its knows the regulatory domain we should be in.
  * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an
  * 	802.11 country information element with regulatory information it
- * 	thinks we should consider.
+ * 	thinks we should consider. cfg80211 only processes the country
+ *	code from the IE, and relies on the regulatory domain information
+ *	structure pased by userspace (CRDA) from our wireless-regdb.
+ *	If a channel is enabled but the country code indicates it should
+ *	be disabled we disable the channel and re-enable it upon disassociation.
  */
 enum nl80211_reg_initiator {
 	NL80211_REGDOM_SET_BY_CORE,
@@ -1413,6 +1448,16 @@ enum nl80211_reg_rule_flags {
  * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
  * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
  * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio
+ *	spent on this channel
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary
+ *	channel was sensed busy (either due to activity or energy detect)
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension
+ *	channel was sensed busy
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent
+ *	receiving data
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent
+ *	transmitting data
  * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
  *	currently defined
  * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
@@ -1422,6 +1467,11 @@ enum nl80211_survey_info {
 	NL80211_SURVEY_INFO_FREQUENCY,
 	NL80211_SURVEY_INFO_NOISE,
 	NL80211_SURVEY_INFO_IN_USE,
+	NL80211_SURVEY_INFO_CHANNEL_TIME,
+	NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY,
+	NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY,
+	NL80211_SURVEY_INFO_CHANNEL_TIME_RX,
+	NL80211_SURVEY_INFO_CHANNEL_TIME_TX,
 
 	/* keep last */
 	__NL80211_SURVEY_INFO_AFTER_LAST,