Permalink
Fetching contributors…
Cannot retrieve contributors at this time
106 lines (80 sloc) 4.32 KB

Mock platform {#mock}

Mocking capability allows libmraa user to work with the library without any real hardware available. Enabling this requires library recompilation with architecture override (see Building section below). When mock is enabled, library simulates actual HW operations at the backend so that for the application it looks like a usual board. Being implemented at the backend, the functionality is available in all language bindings libmraa supports.

Board configuration

This feature is yet in the experimental mode and not all functionality is available. Right now we simulate a single generic board with:

  • GPIO (without ISR)
  • ADC with 10 (std)/12 (max) bit resolution, which returns random values on read
  • Single I2C bus with one device at address 0x33 and 10 bytes of register space, which can be read or written in bytes or words (big-endian). Technically those registers are just an array of uint8_t, so you can treat them as 10 single-byte registers or 5 single-word ones or a mix thereof.
  • Single SPI bus with one Chip Select. All write functions are supported, received data items (words or bytes) are calculated from the sent ones using sent_byte (or word) XOR constant formula. See SPI mock header for constant values.
  • Single UART port. All functions are supported, but many are simple stubs. Write always succeeds, read returns 'Z' symbol as many times as read() requested.

We plan to develop it further and all contributions are more than welcome. See our @ref contributing page for more information.

See the table below for pin layout and features

MRAA Number Pin Name Notes
0 GPIO0 GPIO pin, no muxing, no ISR
1 ADC0 AIO pin, returns random value on read
2 I2C0SDA SDA pin for I2C0 bus
3 I2C0SCL SCL pin for I2C0 bus
4 SPI0CS CS pin for SPI0 bus
5 SPI0MOSI MOSI pin for SPI0 bus
6 SPI0MISO MISO pin for SPI0 bus
7 SPI0SCLK SCLK pin for SPI0 bus
8 UART0RX RX pin for UART0 port
9 UART0TX TX pin for UART0 port

Building

Generally all the building steps are the same as listed in the main @ref building guide, you just need to set some specific CMake options.

Linux

To build under Linux, follow standard instructions, just make sure to set the -DBUILDARCH="MOCK" CMake option.

Windows

Mocking capability allows us to build and use libmraa under Windows. That helps if you e.g. don't want to leave your customary Windows-based Python IDE, but want to develop libmraa-based programs.

Building Node.js bindings was not yet tested under Windows as MSYS2 does not have a ready-made package. Java was not tested either.

Prerequisites

You'll need the following to build libmraa under Windows:

  • MSYS2 basic installation

  • Several additional packages, install them by running

    pacman -S cmake base-devel gcc git

Compiling

The procedure is conceptually the same as under Linux - you first need to run CMake with specific options to generate makefiles and then run make to build everything.

  • Run MSYS2 shell (not a MinGW one)

  • Clone the libmraa git repo (let's assume into /home/test/mraa/mraa-src dir)

  • Create a build directory outside of the clone one (let's say /home/test/mraa/mraa-build)

  • Run CMake, switching off unsupported options and enabling mock platform:

    cmake ../mraa-src/ -DBUILDARCH="MOCK" -DBUILDSWIGNODE=OFF -DENABLEEXAMPLES=OFF
  • Make, install and test:

    make clean && make install && make test

    All tests should pass.

Note: To have autocompletion in Python IDE, just point it to MSYS2's Python and make sure to specify any additional paths pointing to site-packages dir with mraa module if IDE requires that ("Interpreter Paths" in PyCharm). With the above settings the module will be installed into /usr/local/lib/python2.7/site-packages and the libmraa itself - into /usr/local/bin.