CPU 01
BCM33900010
PRID33900010
v4.01
RR:00000003
BFW
AVS init...
B11
STB V=00002823 D=000002c2
DCM V=00002860 D=000002c8
AVS init OK
AVS load:select_image: addr_offset: 00005800 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00005800
LOADED
AVS: overtemp mon ON
I2C @ f040a400.
BID: no ack!
I2C @ f040a400.
WBID: no ack!

======
BOARDS
======

a) BCM93390SV           33900010:00000014
b) BCM93390MWVG         33900010:00000021
c) BCM93390SMWVG                33900010:00000042
d) BCM93390SMWVG_V10            33900010:00000043
e) BCM93390WVG          33900010:00000090
f) BCM93390VMS52S               33900010:00000050
g) BCM93390DCM          33900010:00000061
h) BCM93390PHYDVT               33900010:00000070
i) BCM93390VCM          33900010:00000081
j) BCM97278VMS          33900010:000000f0
k) BCM93390SDVT         33900010:000000a0
l) BCM93390DCMS         33900010:00000062
m) BCM93390VCMS         33900010:00000082
n) BCM93390SMWVG2               33900010:000000b0
o) BCM93390SMWVG2_V10           33900010:000000b1
p) BCM93390VSV          33900010:000000c0
q) BCM93390VVCM         33900010:000000d0

RESET + 1 = this menu
RESET + 8 = bypass AVS
2)  shmoo menu after board menu


Select board type: 
using board #n
OTP Market ID        = 00000000
FSBL Market ID       = 00002900
Market ID Mask       = 00ffff00
Secure Boot
MARKET ID VALIDATION : Generic Mode - PASS
MEMSYS-ALT
MEMSYS AUTHENTICATION: OK
SHMOO 03030100 BLD:memsys_3.3.0.0-5-gbbc1e43a0 HW:hpg0_generic V:3.3.1.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=0000039c(924)
 temperature=00007216(29206)
 PV=0000035c(860)
 MV=00000393(915)
DCD: Current voltage=0000039e(926)
 temperature=00007216(29206)
 PV=00000353(851)
 MV=00000396(918)
AVS FW rev=30313978 [0.1.9.x]
OK
DDR0: MCB#2-1 !@ ffe0e500 <= ffe0e0a8 MEMSYS-0 @ f1500000 
ramSize =   00000400
DDR SCRAMBLER ENABLED
OK
Secure boot detected
COPY CODE... DONE
BOLT VERSION(FSBL): v4.01
BOLT VERSION(SSBL): v4.01
SSBL INTEGRITY: OK
SSBL AUTHENTICATION: OK
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss  0706df10
_ebss  0706eb08
_end   0706eb28
HEAP @ 07100000
STACK @ 07fffff8
ARCH: CONFIG OK
CLR BSS 0706df10 to 0706eb08 OK
CLR SRAM  OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

    ,/    
  ,'/___, BOLT v4.01 v4.01_B1 LOCAL BUILD
.'__  ,'  (2020-02-10 11:05:37 justin@CPE-TC-Build3)
   /,'    Copyright (C) 2020 Broadcom Limited
  /'      

Board: BCM93390SMWVG2
SYS_CTRL: product=3390, family=3390b0, strap=0000441f, 
otp @ 0xf0404030 = 0x060000e0: en_cr(0x00000060) en_testport(0x00000080) 
otp @ 0xf0404034 = 0x00000200: mtsif_enc_ctrl_disable(0x00000200) 
CPU: 2x A15, 1503 MHz
SCB: 324 MHz
DDR0 @ 1067MHz
RESET CAUSE: 0x000003 main_chip_input power_on (2 of 32 possible causes)
CS0: ONFI NAND, 512MB, 128kB blocks, 2048B page, 16B OOB, BCH-4
EMMC1: device probe, no eMMC device found
cannot open flash0.fsbl: -6
cannot open flash0.macadr
cannot get flash info
cannot open flash0.macadr
MAC ADDRESS MUST BE PROGRAMMED; use macprog command
RTS0: 0x21501004, 1 clients, ok
rts 01 [FAKE_NO_RTS]            *default
BOX MODE: 1
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.924V, T=+30.180C, PV=0.860V, MV=0.915V, FW=30313978 [0.1.9.x]
AVS: DCD: V=0.924V, T=+29.693C, PV=0.851V, MV=0.918V
USB @ 0xf1000200: IPP is active low, IOC is negative polarity
USB @ 0xf1010200: IPP is active low, IOC is negative polarity
Board ID is zero! - You need to hardware fix (ECO) it!
board selection update!
board was ?, now n (flags:0xffe00000)
Could not open device 'flash0.fsbl'
Failed.: Device not found
         FCNT not found, defaulting to 0
Watchdog is disabled!
Console is disabled
Executing STARTUP...
Loader:raw Filesys:raw Dev:flash0.devtree0 File:(null) Options:(null)
Loading: ....
 65536 bytes read
Found and loading raw DTB
Loader:zimg Filesys:raw Dev:flash0.kernel0 File:(null) Options:ubi.mtd=flash0.rg0 rootfstype=ubifs root=ubi0:rootfs platformboot ubifs_apps ubifs_data coherent_pool=1M  console=/dev/null noconsole
.
.
.
Reading 3894392 bytes from zImage...........
KERNEL AUTHENTICATION: OK
ByPass TFTP checkNo OPPs generated by bolt
Starting program at 0x8000 (DTB @ 0x7629000)



RG login: