Skip to content


Subversion checkout URL

You can clone with HTTPS or Subversion.

Download ZIP
Fetching contributors…

Cannot retrieve contributors at this time

executable file 183 lines (151 sloc) 7.757 kb
use strict;
use warnings;
use FindBin;
use lib "$FindBin::Bin/lib";
use Getopt::Long;
use Slic3r;
use XXX;
my %opt = ();
my %cli_options = ();
my %options = (
'help' => sub { usage() },
'debug' => \$Slic3r::debug,
'o|output=s' => \$opt{output},
'close-after-slicing' => \$opt{close_after_slicing},
'save=s' => \$opt{save},
'load=s' => \$opt{load},
foreach my $opt_key (keys %$Slic3r::Config::Options) {
my $opt = $Slic3r::Config::Options->{$opt_key};
$options{ $opt->{cli} } = \$cli_options{$opt_key}
if $opt->{cli};
GetOptions(%options) or usage(1);
# load configuration
if ($opt{load}) {
-e $opt{load} or die "Cannot find specified configuration file.\n";
# validate command line options
# apply command line options
Slic3r::Config->set($_ => $cli_options{$_})
for grep defined $cli_options{$_}, keys %cli_options;
# validate configuration
# save configuration
Slic3r::Config->save($opt{save}) if $opt{save};
# start GUI
if (!@ARGV && !$opt{save} && eval "require Slic3r::GUI; 1") {
if ($ARGV[0]) {
# skein
my $input_file = $ARGV[0];
my $skein = Slic3r::Skein->new(
input_file => $input_file,
output_file => $opt{output},
} else {
usage(1) unless $opt{save};
sub usage {
my ($exit_code) = @_;
print <<"EOF";
Slic3r $Slic3r::VERSION is a STL-to-GCODE translator for RepRap 3D printers
written by Alessandro Ranellucci <aar\> -
Usage: [ OPTIONS ] file.stl
--help Output this usage screen and exit
--save <file> Save configuration to the specified file
--load <file> Load configuration from the specified file
-o, --output File to output gcode to (default: <inputfile>.gcode)
Printer options:
--nozzle-diameter Diameter of nozzle in mm (default: $Slic3r::nozzle_diameter)
--print-center Coordinates of the point to center the print around
(default: $Slic3r::print_center->[0],$Slic3r::print_center->[1])
Use relative distances for extrusion in GCODE output
--extrusion-axis The axis used for extrusion; leave empty to disable extrusion
(default: $Slic3r::extrusion_axis)
--z-offset Additional height in mm to add to vertical coordinates
(+/-, default: $Slic3r::z_offset)
--gcode-arcs Use G2/G3 commands for native arcs (experimental, not supported
by all firmwares)
--g0 Use G0 commands for retraction (experimenta, not supported by all
Filament options:
--filament-diameter Diameter in mm of your raw filament (default: $Slic3r::filament_diameter)
Change this to alter the amount of plastic extruded. There should be
very little need to change this value, which is only useful to
compensate for filament packing (default: $Slic3r::extrusion_multiplier)
--temperature Extrusion temperature, set 0 to disable (default: $Slic3r::temperature)
Speed options:
--travel-speed Speed of non-print moves in mm/sec (default: $Slic3r::travel_speed)
--perimeter-speed Speed of print moves for perimeters in mm/sec (default: $Slic3r::perimeter_speed)
Speed of print moves for small perimeters in mm/sec (default: $Slic3r::small_perimeter_speed)
--infill-speed Speed of print moves in mm/sec (default: $Slic3r::infill_speed)
--solid-infill-speed Speed of print moves for solid surfaces in mm/sec (default: $Slic3r::solid_infill_speed)
--bridge-speed Speed of bridge print moves in mm/sec (default: $Slic3r::bridge_speed)
Factor to increase/decrease speeds on bottom
layer by (default: $Slic3r::bottom_layer_speed_ratio)
Accuracy options:
--layer-height Layer height in mm (default: $Slic3r::layer_height)
Multiplication factor for the height to slice and print the first
layer with (> 0, default: $Slic3r::first_layer_height_ratio)
Infill every N layers (default: $Slic3r::infill_every_layers)
Calculate the extrusion width as the layer height multiplied by
this value (> 0, default: calculated automatically)
--bridge-flow-ratio Multiplier for extrusion when bridging (> 0, default: $Slic3r::bridge_flow_ratio)
Print options:
--perimeters Number of perimeters/horizontal skins (range: 1+,
default: $Slic3r::perimeters)
--solid-layers Number of solid layers to do for top/bottom surfaces
(range: 1+, default: $Slic3r::solid_layers)
--fill-density Infill density (range: 0-1, default: $Slic3r::fill_density)
--fill-angle Infill angle in degrees (range: 0-90, default: $Slic3r::fill_angle)
--fill-pattern Pattern to use to fill non-solid layers (default: $Slic3r::fill_pattern)
--solid-fill-pattern Pattern to use to fill solid layers (default: $Slic3r::solid_fill_pattern)
--start-gcode Load initial gcode from the supplied file. This will overwrite
the default command (home all axes [G28]).
--end-gcode Load final gcode from the supplied file. This will overwrite
the default commands (turn off temperature [M104 S0],
home X axis [G28 X], disable motors [M84]).
Retraction options:
--retract-length Length of retraction in mm when pausing extrusion
(default: $Slic3r::retract_length)
--retract-speed Speed for retraction in mm/sec (default: $Slic3r::retract_speed)
Additional amount of filament in mm to push after
compensating retraction (default: $Slic3r::retract_restart_extra)
Only retract before travel moves of this length (default: $Slic3r::retract_before_travel)
--retract-lift Lift Z by the given distance in mm when retracting (default: $Slic3r::retract_lift)
Skirt options:
--skirts Number of skirts to draw (default: $Slic3r::skirts)
--skirt-distance Distance in mm between innermost skirt and object
(default: $Slic3r::skirt_distance)
--skirt-height Height of skirts to draw (expressed in layers, default: $Slic3r::skirt_height)
Transform options:
--scale Factor for scaling input object (default: $Slic3r::scale)
--rotate Rotation angle in degrees (0-360, default: $Slic3r::rotate)
--duplicate-x Number of items along X axis (1+, default: $Slic3r::duplicate_x)
--duplicate-y Number of items along Y axis (1+, default: $Slic3r::duplicate_y)
--duplicate-distance Distance in mm between copies (default: $Slic3r::duplicate_distance)
exit ($exit_code || 0);
Jump to Line
Something went wrong with that request. Please try again.