Permalink
Commits on May 14, 2013
  1. WIP for now.

    Jordan Miller committed May 14, 2013
Commits on May 12, 2013
  1. 3000 mm/min for all default speeds. relatively quick with no resonanc…

    …e sounds
    Jordan Miller committed May 12, 2013
  2. don't home_retract_mm. set to 0 mm for x y z.

    Jordan Miller committed May 12, 2013
  3. slow down homing_feedrate too.

    Jordan Miller committed May 12, 2013
  4. let's start off with slower speeds, k? thx.

    Jordan Miller committed May 12, 2013
Commits on May 9, 2013
  1. flipped y-axis again, changed all max speeds and accelerations and je…

    …rk settings based on testing. Set X Y and Z all the same. This ROCKS.
    Jordan Miller committed May 9, 2013
  2. had to invert Y and Z Motors

    Jordan Miller committed May 9, 2013
  3. ShopBot Moved! Now changed to 4000 steps per inch which is the settin…

    …g ShopBot Gave Us
    Jordan Miller committed May 9, 2013
  4. Redefined Pins.h to follow JohnnyR's MotorExt pin diagram and details…

    …. Ready to try with ShopBot
    Jordan Miller committed May 9, 2013
  5. first mods preparing for ShopBot Desktop 3D Printing. Marlin works an…

    …d can drive x-motor no probs on this RAMBo board.
    Jordan Miller committed May 9, 2013
Commits on Aug 27, 2012
  1. doing 1/8th stepping on x and y since 1/16th stepping setting is in r…

    …eality only 1/8th stepping max.
    Jordan Miller committed Aug 27, 2012
Commits on Aug 13, 2012
  1. Upgraded ChenLab Komodo to RAMBO prototype 2 based on Hive Komodo RAM…

    …BO prototype 2. Ready for sugar printing and plastic printing. MakerGear Extruder Motor only takes a little bit of current compared to Extruder built from Phidgets 0.9 degree motors.
    Jordan Miller committed Aug 13, 2012
Commits on Aug 5, 2012
Commits on Jul 28, 2012
  1. FINAL MODS for version 1.0. Forgot I am using TechPaladin pulleys, NO…

    …T Misumi Pulleys. Aack. Now we are correct scale for x and y and e. Printing like a champ!
    Jordan Miller committed Jul 28, 2012
Commits on Jul 26, 2012
  1. calibrated and ready to print. WIN

    Jordan Miller committed Jul 26, 2012
  2. Y is Y, E0 is E0, E1 is Z2. DONE AND DONE.

    Jordan Miller committed Jul 26, 2012
  3. decrease extruder min temp

    Jordan Miller committed Jul 26, 2012
  4. problem with e-enable?

    Jordan Miller committed Jul 26, 2012
  5. y is y again, now make e1 z2 and make e0 e0 again

    Jordan Miller committed Jul 26, 2012
Commits on Jun 27, 2012
  1. missed a few lines in planner.cpp. maybe this will fix the order of o…

    …perations where M106 stays on but replacing with M126 would fail
    Jordan Miller committed Jun 27, 2012
  2. IT WORKS! enabled RAMBO pin 6 and 7 for PWM like FAN with High PWM fr…

    …equency to decrease noise. Want very smooth PWM here, so high frequency should help
    Jordan Miller committed Jun 27, 2012
Commits on Jun 26, 2012
  1. try increased current to improve torque and do 1/2 stepping on z only…

    … to improve torque there. exercise gcode for z-axis shows a bit of loss in z-position over time when running very fast
    Jordan Miller committed Jun 26, 2012
  2. 1/16th stepping on all axes, 1/4 stepping on Z axis, Z axis motors sp…

    …lit between Z and E0 drivers FTW. This bot rocks even at 1100 mm/min z travel. WIN!
    Jordan Miller committed Jun 26, 2012
  3. moving z consistently at 600 mm/min w00t!

    Jordan Miller committed Jun 26, 2012
  4. commenting out REV_E_DIR and NORM_E_DIR

    Jordan Miller committed Jun 26, 2012
  5. more edits, still not inverting direction though.

    Jordan Miller committed Jun 26, 2012
  6. don't forget to invert the direction as well!

    Jordan Miller committed Jun 26, 2012
  7. got help from Erik van der Zalm. now it compiles. thanks! trying righ…

    …t now...
    Jordan Miller committed Jun 26, 2012
  8. still not working, getting help from EvdZ

    Jordan Miller committed Jun 26, 2012
  9. set E0 to be microstepping 1 just like Z-axis and drop the current to…

    … each driver so we can do single motors at high torque
    Jordan Miller committed Jun 26, 2012
  10. attempt to get z movements to output to E0 pins. Let's get some more …

    …power here to z-axis since we don't need an extruder motor for this application
    Jordan Miller committed Jun 26, 2012
  11. Komodo and Marlin and RAMBO working together. Now let's kick it up a …

    …notch. Note: Phidgets Motors are best at 2.4A, but not good for x and y axes at 255. so x and y at 185, z is shared with motors in SERIES, so z should be 255
    Jordan Miller committed Jun 26, 2012
  12. first attempt to drive komodo printer with rambo board

    Jordan Miller committed Jun 26, 2012