Update README.md

README.md

@@ -306,7 +306,7 @@ If you are using PulseAudio in the standard "user" mode, you can not start Shair
 **(2) Settings:**
 To get the best from Shairport Sync, you’ll need to (a) give Shairport Sync a service name by which it will be seen in iTunes etc. and (b) specify the backend you wish to use - `alsa` for the ALSA backend, or `pa` for the PulseAudio back end. If only one backend is included at compilation, or if the backend is ALSA, there is no need to explicitly specify the backend.
 
-For the ALSA backend you may need to (c) specify the output device to use and (d) specify the name of the mixer volume control to use to control the output level. To get values for (b) and (c) you might need to explore the ALSA output devices with a program like `alsamixer` or similar.
+For the ALSA backend you may need to (c) specify the output device to use and (d) specify the name of the mixer volume control to use to control the output level. To get values for (c) and (d) you might need to explore the ALSA output devices with a program like `alsamixer` or similar.
 
 Shairport Sync reads settings from a configuration file at `/etc/shairport-sync.conf` (note that in FreeBSD it will be at `/usr/local/etc/shairport-sync.conf`). When you run `$sudo make install`, a sample configuration file is installed or updated at `/etc/shairport-sync.conf.sample` (`/usr/local/etc/shairport-sync.conf.sample` in FreeBSD). This contains all the setting groups and all the settings available, but they all are commented out (comments begin with `//`) so that default values are used. The file contains explanations of the settings, useful hints and suggestions. In addition, if the file doesn't already exist, a default configuration is installed, which should work in almost any system with a sound card.
 
@@ -326,7 +326,7 @@ general =
 ```
   output_backend = "pa";
 ```
-to the `general` stanza.
+to the `general` group.
 
 The `alsa` group is used to specify properties of the output device. The most obvious setting is the name of the output device which you can set using the `output_device` tag.
 
@@ -350,7 +350,7 @@ Shairport Sync can run programs just before it starts to play an audio stream an
 
 Note that the full path to the programs must be specified, and script files will not be executed unless they are marked as executable and have the appropriate shebang `#!/bin/...` as the first line. (This behaviour may be different from other Shairports.)
 
-Shairport Sync can run a program whenever the volume is set or changed. You specify them using the `general` group settings `run_this_when_volume_changes`. This is to facilitate situations where something has to be done when the volume changes, e.g. adjust an external mixer value. Set the `wait_for_completion` value to `"yes"` for Shairport Sync to wait until the command has been completed before continuing. Again, please note that the full path to the program must be specified, and script files will not be executed unless they are marked as executable and have the appropriate shebang `#!/bin/...` as the first line.
+Shairport Sync can run a program whenever the volume is set or changed. You specify it using the `general` group setting `run_this_when_volume_changes`. This is to facilitate situations where something has to be done when the volume changes, e.g. adjust an external mixer value. Set the `wait_for_completion` value to `"yes"` for Shairport Sync to wait until the command has been completed before continuing. Again, please note that the full path to the program must be specified, and script files will not be executed unless they are marked as executable and have the appropriate shebang `#!/bin/...` as the first line.
 
 Note: Shairport Sync can take configuration settings from command line options. This is mainly for backward compatibility, but sometimes still useful. For normal use, it is strongly recommended that you use the configuration file method.