dallasMQTT is a service that will periodically poll an arbitray number of dallas 1 wire sensors and publish the data to an MQTT broker.
dallasMQTT is availably via pypi, so all you need to do is run:
pip install -U dallasMQTT
assuming you have pip installed. (which is the recommended way to install. If you need to use a development version of dallasMQTT you can clone the repo and install it locally with:
git clone https://github.com/mtreinish/dallasMQTT.git
and then install it with:
pip install -e dallasMQTT
which will install dallasMQTT in your python environment in editable mode for local development.
If you don't have pip installed you can manually install dallasMQTT by cloning the repo and installing it from the repo base dir with:
python setup.py install
but, note installing via pip is the recommended and supported method of installing dallasMQTT. (even from a local git clone)
To configure dallasMQTT you need to create configuration yaml file that will tell dallasMQTT how to access sensors, how to use MQTT, etc. The basic format of the file with the 3 sections is:
mqtt: hostname: foo sensors: - id: id number name: 'My Sensor' default: poll_rate: 60 base_topic: a_topic
MQTT Section Configuration
This section is used to configure how dallasMQTT will connect to an MQTT broker.
To configure the
mqtt section there are 3 options it currently takes:
of these only
hostname is required. The other 2 options are optional
you can use
password if client auth is desired (or
required by your mqtt broker).
Sensor Section Configuration
sensor section of the yaml config file is used to specify which sensors
are to be polled and how to label them in the mqtt topics. It takes in a list
of sensors of arbitrary size that takes in a combination of sensor ids and names
for example if there were 3 sensors it would look something like:
sensors: - id: 28-000001 name: Sensor1 - id: 28-000002 name: Sensor2 - id: 28-000003 name: Sensor3
This pattern is just repeated for how ever many sensors you want dallasMQTT to
name field is fairly self explanatory, and it is just the name
of the sensor that will be used as the second half of the topic on mqtt, like:
The id field is used to specify the sensor id to poll. dallasMQTT will poll the sensor file at:
So ensuring you put the proper id here is important otherwise dallasMQTT will not be able to read the sensor data.
This section was written to be sufficiently broad so that in the future additional sensor types could be added to dallasMQTT. This would be a very simple addition and would just require adding an optional driver field to each list element which would tell dallasMQTT which class to use for polling sensors. (these additional sensor wouldn't necessarily have to be dallas 1 wire either) But, as of right now there is only 1 class, DallasTemp, for 1 wire temperature sensors, so this field doesn't exist. However, if/when dallasMQTT is updated to include other sensor types the documentation will be updated. (and backwards compatibility will be adhered to so as to not break anyone)
Default Section configuration
The default section is where you configure settings that contol the basic operation of dallasMQTT. There are 3 options in this section right now:
All 3 options are optional.
base_topic is used to set the basic topic used on MQTT for sending sensor
data. The messages will be sent on mqtt like:
by default this is set to
poll_rate is used to specify a time in seconds to wait between polling
the sensors on a worker thread. Note this is not time between individual sensors
but between polling all the sensors being handled by a single thread. Each
sensor in that group will be polled serially without any wait time between
max_threads is used to specify the maximum number of threads that dallasMQTT
will launch to poll sensors with. If there are less sensors in the configuration
file a single worker thread will be launched for each sensor. If there are more
sensors than threads the sensors will be equally distributed to the number of
workers specified. Each worker will handle polling the list of sensors it
To run dallasMQTT is fairly straightforward. After dallasMQTT is installed you just run:
where config.yaml is the path to your yaml config file.