Skip to content
Permalink
Browse files

ath79: Add support for Ubiquiti Nanostation M (XW)

CPU:  AR9342 SoC
RAM:      64 MB DDR2
Flash:     8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN:  2.4/5 GHz
UART:      1 UART
LEDs:        Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:     Reset

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
  • Loading branch information...
ynezz authored and dangowrt committed Dec 12, 2018
1 parent 368b6d1 commit 40530c8eb42aa4b98de10621b6c1c89030f00d0a
@@ -149,6 +149,7 @@ tplink,tl-wr841-v11)
ubnt,bullet-m|\
ubnt,bullet-m-xw|\
ubnt,nano-m|\
ubnt,nanostation-m-xw|\
ubnt,rocket-m)
ucidef_set_rssimon "wlan0" "200000" "1"
ucidef_set_led_rssi "rssilow" "RSSILOW" "ubnt:red:link1" "wlan0" "1" "100"
@@ -212,6 +212,10 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth1" "2:lan:3" "3:lan:2" "4:lan:1"
;;
ubnt,nanostation-m-xw)
ucidef_add_switch "switch0" \
"0@eth0" "5:lan" "1:wan"
;;
ubnt,nanostation-ac|\
ubnt,unifiac-mesh-pro|\
ubnt,unifiac-pro)
@@ -0,0 +1,37 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "ar9342_ubnt_xw.dtsi"

/ {
compatible = "ubnt,nanostation-m-xw", "ubnt,xw", "qca,ar9342";
model = "Ubiquiti Nanostation M (XW)";
};

&mdio0 {
status = "okay";

phy4-mii-enable;
phy-mask = <0x23>;

phy4: ethernet-phy@0 {
reg = <0>;
phy-mode = "mii";
};
};

&eth0 {
status = "okay";

phy-mode = "mii";
phy-handle = <&phy4>;

gmac-config {
device = <&gmac>;
mii-gmac0 = <1>;
mii-gmac0-slave = <1>;
};
};
@@ -113,6 +113,12 @@ define Device/ubnt_nano-m
endef
TARGET_DEVICES += ubnt_nano-m

define Device/ubnt_nanostation-m-xw
$(Device/ubnt-xw)
DEVICE_TITLE := Ubiquiti Nanostation M (XW)
endef
TARGET_DEVICES += ubnt_nanostation-m-xw

define Device/ubnt_lap-120
$(Device/ubnt-wa)
DEVICE_TITLE := Ubiquiti LiteAP ac (LAP-120)

0 comments on commit 40530c8

Please sign in to comment.
You can’t perform that action at this time.