Skip to content
Permalink
Browse files

ramips: add support for GL.iNet VIXMINI

Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
  • Loading branch information...
blocktrron authored and chunkeey committed Apr 12, 2019
1 parent b3f7a73 commit 43e8c37cb4da64a12a3cb88a84b19db7f2fc640c
@@ -367,6 +367,7 @@ ramips_setup_interfaces()
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5:wan" "6@eth0"
;;
dlink,dir-510l|\
glinet,vixmini|\
netgear,ex6150|\
re350-v1)
ucidef_add_switch "switch0" \
@@ -0,0 +1,114 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include "mt7628an.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/{
compatible = "glinet,vixmini", "mediatek,mt7628an-soc";
model = "GL.iNet VIXMINI";

aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};

chosen {
bootargs = "console=ttyS0,115200";
};

memory@0 {
device_type = "memory";
reg = <0x0 0x4000000>;
};

leds {
compatible = "gpio-leds";

led_power: power {
label = "vixmini:blue:power";
default-state = "on";
gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
};

wlan {
label = "vixmini:white:wlan";
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};

keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;

reset {
label = "reset";
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
};

&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "wdt", "wled_an", "p1led_an";
ralink,function = "gpio";
};
};
};

&ethernet {
mtd-mac-address = <&factory 0x4>;
};

&wmac {
status = "okay";

ralink,mtd-eeprom = <&factory 0x0>;
};

&spi0 {
status = "okay";

flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;

partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;

partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};

partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};

factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};

partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x50000 0x7b0000>;
};
};
};
};
@@ -66,6 +66,14 @@ define Device/gl-mt300n-v2
endef
TARGET_DEVICES += gl-mt300n-v2

define Device/glinet_vixmini
DTS := VIXMINI
IMAGE_SIZE := 7872k
DEVICE_TITLE := GL.iNet VIXMINI
SUPPORTED_DEVICES += vixmini
endef
TARGET_DEVICES += glinet_vixmini

define Device/hc5661a
DTS := HC5661A
IMAGE_SIZE := $(ralink_default_fw_size_16M)

0 comments on commit 43e8c37

Please sign in to comment.
You can’t perform that action at this time.