Skip to content
Permalink
Browse files

ath79: add support for D-Link DIR-859 A1

Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880

USB is supported on the PCB but not connected.

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or the u-boot
   failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted. Otherwise the u-boot
   will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the firmware
   checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
   upgrade the factory.bin through the u-boot failsafe interface and then goto
   step 2.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
  • Loading branch information...
hackpascal authored and mkresin committed Dec 29, 2018
1 parent fd35c5b commit abc7ed2c58860fc1363129efbe9e8c60f81a802c
@@ -28,6 +28,9 @@ buffalo,whr-g301n)
ucidef_set_led_switch "lan3" "LAN3" "$boardname:green:lan3" "switch0" "0x08"
ucidef_set_led_switch "lan4" "LAN4" "$boardname:green:lan4" "switch0" "0x10"
;;
dlink,dir-859-a1)
ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20"
;;
etactica,eg200)
ucidef_set_led_netdev "lan" "LAN" "$boardname:red:eth0" "eth0"
ucidef_set_led_oneshot "modbus" "Modbus" "$boardname:red:modbus" "100" "33"
@@ -158,6 +158,7 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
;;
dlink,dir-859-a1|\
tplink,tl-wr1043nd-v4)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
@@ -234,6 +235,10 @@ ath79_setup_macs()
lan_mac=$(mtd_get_mac_text "mac" 4)
wan_mac=$(mtd_get_mac_text "mac" 24)
;;
dlink,dir-859-a1)
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
;;
elecom,wrc-300ghbk2-i)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2)
;;
@@ -105,6 +105,10 @@ case "$FIRMWARE" in
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac_crc $(mtd_get_mac_text "mac" 4) 2
;;
dlink,dir-859-a1)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata "wlan24mac") 2
;;
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2|\
iodata,wn-ag300dgr)
@@ -92,6 +92,10 @@ case "$FIRMWARE" in
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
;;
dlink,dir-859-a1)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
;;
glinet,gl-x750)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
@@ -168,6 +168,7 @@ CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPLIT_FIRMWARE=y
CONFIG_MTD_SPLIT_LZMA_FW=y
CONFIG_MTD_SPLIT_SEAMA_FW=y
CONFIG_MTD_SPLIT_TPLINK_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_MTD_TPLINK_PARTS=y
@@ -0,0 +1,177 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "qca956x.dtsi"

/ {
model = "D-Link DIR-859 A1";
compatible = "dlink,dir-859-a1", "qca,qca9563";

aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-upgrade = &power;
};

chosen {
bootargs = "console=ttyS0,115200n8";
};

leds {
compatible = "gpio-leds";

wps {
label = "dir-859-a1:green:wps";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};

power: power {
label = "dir-859-a1:green:power";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};

internet {
label = "dir-859-a1:green:internet";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};

wlan {
label = "dir-859-a1:green:wlan";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};

keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;

wps {
linux,code = <KEY_RESTART>;
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};

reset {
linux,code = <KEY_RESTART>;
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};

gpio-export {
compatible = "gpio-export";
#size-cells = <0>;

gpio_switch_reset {
gpio-export,name = "dir-859-a1:reset:switch";
gpio-export,output = <1>;
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
};
};
};

&uart {
status = "okay";
};

&gpio {
status = "okay";
};

&pcie {
status = "okay";
};

&spi {
num-cs = <1>;

status = "okay";

flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <30000000>;

partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;

partition@0 {
label = "bootloader";
reg = <0x000000 0x40000>;
read-only;
};

partition@40000 {
label = "bdcfg";
reg = <0x040000 0x10000>;
read-only;
};

partition@50000 {
label = "devdata";
reg = <0x050000 0x10000>;
read-only;
};

partition@60000 {
label = "devconf";
reg = <0x060000 0x10000>;
read-only;
};

partition@70000 {
compatible = "seama";
label = "firmware";
reg = <0x070000 0xf80000>;
};

art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};

&mdio0 {
status = "okay";

phy-mask = <0>;

phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "sgmii";

qca,ar8327-initvals = <
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
0x10 0x81000080 /* POWER_ON_STRIP */
0x50 0xcc35cc35 /* LED_CTRL0 */
0x54 0xcb37cb37 /* LED_CTRL1 */
0x58 0x00000000 /* LED_CTRL2 */
0x5c 0x00f3cf00 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
};

&eth0 {
status = "okay";

pll-data = <0x03000101 0x00000101 0x00001919>;

phy-mode = "sgmii";
phy-handle = <&phy0>;
};

&wmac {
status = "okay";
qca,no-eeprom;
};
@@ -2,6 +2,7 @@ include ./common-buffalo.mk
include ./common-netgear.mk

DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK

define Build/cybertan-trx
@echo -n '' > $@-empty.bin
@@ -53,6 +54,23 @@ define Build/nec-fw
mv $@.new $@
endef

define Device/seama
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
IMAGES += factory.bin
SEAMA_MTDBLOCK := 1

# 64 bytes offset:
# - 28 bytes seama_header
# - 36 bytes of META data (4-bytes aligned)
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := \
$$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin := \
$$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | check-size $$$$(IMAGE_SIZE)
SEAMA_SIGNATURE :=
endef

define Device/avm_fritz300e
ATH_SOC := ar7242
DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E
@@ -192,6 +210,17 @@ define Device/dlink_dir-835-a1
endef
TARGET_DEVICES += dlink_dir-835-a1

define Device/dlink_dir-859-a1
$(Device/seama)
ATH_SOC := qca9563
DEVICE_TITLE := D-LINK DIR-859 A1
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
SUPPORTED_DEVICES += dir-859-a1
endef
TARGET_DEVICES += dlink_dir-859-a1

define Device/elecom_wrc-300ghbk2-i
ATH_SOC := qca9563
DEVICE_TITLE := ELECOM WRC-300GHBK2-I

0 comments on commit abc7ed2

Please sign in to comment.
You can’t perform that action at this time.