From f1c041e34f9742fcdd0c8c65f69888d3ec580541 Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Mon, 25 May 2020 14:50:20 -0700 Subject: [PATCH] ipq40xx: Add subtarget for Google WiFi (Gale) Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port. In its stock configuration, it runs a Chromium OS-based system, but you wouldn't know it, since you can only manage it via a "cloud" + mobile-app system. The "v2" label is coded into the bootloader, which prefers the "google,gale-v2" compatible string. I believe "v1" must have been pre-release hardware. Note: this is *not* the Google Nest WiFi, released in 2019. I include "factory.bin" support, where we generate a GPT-based disk image with 2 partitions -- a kernel partition (using the custom "Chrome OS kernel" GUID type) and a root filesystem partition. See below for flashing instructions. Sysupgrade is supported via recent emmc_do_upgrade() helper. This is a subtarget because it enables different features (FEATURES=boot-part rootfs-part) whose configurations don't make sense in the "generic" target, and because it builds in a few USB drivers, which are necessary for installation (installation is performed by booting from USB storage, and so these drivers cannot be built as modules, since we need to load modules from USB storage). Flashing instructions ===================== Documented here: https://openwrt.org/inbox/toh/google/google_wifi Note this requires booting from USB storage. Features ======== I've tested: * Ethernet, both WAN and LAN ports * eMMC * USB-C (hub, power-delivery, peripherals) * LED0 (R/G/B) * WiFi (limited testing) * SPI flash * Serial console: once in developer mode, console can be accessed via the USB-C port with SuzyQable, or other similar "Closed Case Debugging" tools: https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable * Sysupgrade Not tested: * TPM Known not working: * Reboot: this requires some additional TrustZone / SCM configuration to disable Qualcomm's SDI. I have a proposal upstream, and based on IRC chats, this might be acceptable with additional DT logic: [RFC PATCH] firmware: qcom_scm: disable SDI at boot https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/ * SMP: enabling secondary CPUs doesn't currently work using the stock bootloader, as the qcom_scm driver assumes newer features than this TrustZone firmware has. I posted notes here: [RFC] qcom_scm: IPQ4019 firmware does not support atomic API? https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/ * There's a single external button, and a few useful internal GPIO switches. I haven't hooked them up. The first two are fixed with subsequent commits. Additional notes ================ Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which the manufacturer image uses. Note: the manufacturer bootloader knows how to patch in calibration data via the wifi{0,1} aliases in the DTB, so while these properties aren't present in the DTS, they are available at runtime: # ls -l /sys/firmware/devicetree/base/soc/wifi@a*/qcom,ath10k-pre-calibration-data -r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a000000/qcom,ath10k-pre-calibration-data -r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a800000/qcom,ath10k-pre-calibration-data Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases. Signed-off-by: Brian Norris (updated 901 - x1pro moved in the process) Signed-off-by: Christian Lamparter --- target/linux/ipq40xx/Makefile | 2 +- .../ipq40xx/base-files/etc/board.d/02_network | 1 + .../base-files/lib/upgrade/platform.sh | 10 +- target/linux/ipq40xx/chromium/config-default | 10 + target/linux/ipq40xx/chromium/target.mk | 2 + .../arch/arm/boot/dts/qcom-ipq4019-wifi.dts | 413 ++++++++++++++++++ target/linux/ipq40xx/image/chromium.mk | 14 + .../901-arm-boot-add-dts-files.patch | 5 +- 8 files changed, 453 insertions(+), 4 deletions(-) create mode 100644 target/linux/ipq40xx/chromium/config-default create mode 100644 target/linux/ipq40xx/chromium/target.mk create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts diff --git a/target/linux/ipq40xx/Makefile b/target/linux/ipq40xx/Makefile index fb003243ccc38..9bdb55d7838e8 100644 --- a/target/linux/ipq40xx/Makefile +++ b/target/linux/ipq40xx/Makefile @@ -6,7 +6,7 @@ BOARDNAME:=Qualcomm Atheros IPQ40XX FEATURES:=squashfs fpu ramdisk nand CPU_TYPE:=cortex-a7 CPU_SUBTYPE:=neon-vfpv4 -SUBTARGETS:=generic mikrotik +SUBTARGETS:=generic chromium mikrotik KERNEL_PATCHVER:=5.10 KERNEL_TESTING_PATCHVER:=5.10 diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 2aa4886e6a57b..f3dfd656c3ab6 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -46,6 +46,7 @@ ipq40xx_setup_interfaces() cilab,meshpoint-one|\ edgecore,ecw5211|\ edgecore,oap100|\ + google,wifi|\ openmesh,a42|\ openmesh,a62) ucidef_set_interfaces_lan_wan "eth1" "eth0" diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index e8c94409a7cc0..cded9e3a7ff78 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -152,6 +152,13 @@ platform_do_upgrade() { compex,wpj419) nand_do_upgrade "$1" ;; + google,wifi) + export_bootdevice + export_partdevice CI_ROOTDEV 0 + CI_KERNPART="kernel" + CI_ROOTPART="rootfs" + emmc_do_upgrade "$1" + ;; linksys,ea6350v3 |\ linksys,ea8300 |\ linksys,mr8300) @@ -200,7 +207,8 @@ platform_do_upgrade() { platform_copy_config() { case "$(board_name)" in - glinet,gl-b2200) + glinet,gl-b2200 |\ + google,wifi) emmc_copy_config ;; esac diff --git a/target/linux/ipq40xx/chromium/config-default b/target/linux/ipq40xx/chromium/config-default new file mode 100644 index 0000000000000..83a42dfb663b0 --- /dev/null +++ b/target/linux/ipq40xx/chromium/config-default @@ -0,0 +1,10 @@ +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_SCSI_REQUEST=y +CONFIG_SCSI=y +CONFIG_SG_POOL=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_HOST=y +CONFIG_USB_DWC3_QCOM=y +CONFIG_USB_STORAGE=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PLATFORM=y diff --git a/target/linux/ipq40xx/chromium/target.mk b/target/linux/ipq40xx/chromium/target.mk new file mode 100644 index 0000000000000..3983a9281a5d2 --- /dev/null +++ b/target/linux/ipq40xx/chromium/target.mk @@ -0,0 +1,2 @@ +BOARDNAME:=Google Chromium +FEATURES += emmc boot-part rootfs-part diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts new file mode 100644 index 0000000000000..9448e5145e29c --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts @@ -0,0 +1,413 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2016, 2018 The Linux Foundation. All rights reserved. + * Copyright (c) 2016 Google, Inc + */ + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Google WiFi (Gale)"; + compatible = "google,wifi", "google,gale-v2", "qcom,ipq4019"; + + chosen { + /* + * rootwait: in case we're booting from slow/async USB storage. + */ + bootargs-append = " rootwait"; + stdout-path = &blsp1_uart1; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512MB */ + }; + + soc { + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + }; +}; + +&tlmm { + fw_pinmux { + wp { + pins = "gpio53"; + output-low; + }; + recovery { + pins = "gpio57"; + bias-none; + }; + developer { + pins = "gpio41"; + bias-none; + }; + }; + + reset802_15_4 { + pins = "gpio60"; + }; + + led_reset { + pins = "gpio22"; + output-high; + }; + + sys_reset { + pins = "gpio19"; + output-high; + }; + + rx_active { + pins = "gpio43"; + bias-pull,down; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14","gpio15"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + }; + pinconf { + pins = "gpio13", "gpio14","gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + spi_1_pins: spi_1_pinmux { + pinmux { + function = "blsp_spi1"; + pins = "gpio44", "gpio46","gpio47"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio45"; + }; + pinconf { + pins = "gpio44", "gpio46","gpio47"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio45"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + serial_0_pins: serial0_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9", "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + i2c_0_pins: i2c_0_pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + drive-open-drain; + }; + }; + + i2c_1_pins: i2c_1_pinmux { + mux { + pins = "gpio34", "gpio35"; + function = "blsp_i2c1"; + drive-open-drain; + }; + }; + + sd_0_pins: sd_0_pinmux { + sd0 { + pins = "gpio23", "gpio24", "gpio25", "gpio26", "gpio29", "gpio30", "gpio31", "gpio32"; + function = "sdio"; + drive-strength = <10>; + bias-pull-up; + pull-up-res = <0>; + }; + sdclk { + pins = "gpio27"; + function = "sdio"; + drive-strength = <2>; + bias-pull-up; + pull-up-res = <0>; + }; + sdcmd { + pins = "gpio28"; + function = "sdio"; + drive-strength = <10>; + bias-pull-up; + pull-up-res = <0>; + }; + }; + + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-disable; + }; + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-disable; + }; + mux_3 { + pins = "gpio40"; + function = "gpio"; + bias-disable; + output-high; + }; + }; + + wifi1_1_pins: wifi2_pinmux { + mux { + pins = "gpio58"; + output-low; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_i2c3 { + pinctrl-0 = <&i2c_0_pins>; + pinctrl-names = "default"; + status = "okay"; + + tpm@20 { + compatible = "infineon,slb9645tt"; + reg = <0x20>; + powered-while-suspended; + }; +}; + +&blsp1_i2c4 { + pinctrl-0 = <&i2c_1_pins>; + pinctrl-names = "default"; + status = "okay"; + + led-controller@32 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "national,lp5523"; + reg = <0x32>; + clock-mode = /bits/ 8 <1>; + +#if 1 + led@0 { + reg = <0>; + chan-name = "LED0_Red"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + + led@1 { + reg = <1>; + chan-name = "LED0_Green"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + + led@2 { + reg = <2>; + chan-name = "LED0_Blue"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; +#else + /* + * openwrt isn't ready to handle multi-intensity leds yet + * # echo 255 255 255 > /sys/class/leds/tricolor/multi_intensity + * # echo 255 > /sys/class/leds/tricolor/brightness + */ + multi-led@2 { + reg = <2>; + color = ; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + chan-name = "tricolor"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + + led@1 { + reg = <1>; + chan-name = "tricolor"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + + led@2 { + reg = <2>; + chan-name = "tricolor"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + }; +#endif + }; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_spi2 { + pinctrl-0 = <&spi_1_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; + + /* + * This "spidev" was included in the manufacturer device tree. I + * suspect it's the (unused; and removed from later HW spins) Zigbee + * radio -- SiliconLabs EM3581 Zigbee? There's no driver or binding for + * this at the moment. + */ + spidev@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&gmac0 { + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <2 0x20>; +}; + +&gmac1 { + qcom,phy_mdio_addr = <3>; + qcom,forced_duplex = <1>; + vlan_tag = <1 0x10>; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; +}; + +&prng { + status = "okay"; +}; + +&sdhci { + status = "okay"; + pinctrl-0 = <&sd_0_pins>; + pinctrl-names = "default"; + clock-frequency = <192000000>; + vqmmc-supply = <&vqmmc>; + non-removable; +}; + +&usb2 { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&vqmmc { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "GO_GALE"; +}; + +&wifi1 { + status = "okay"; + pinctrl-0 = <&wifi1_1_pins>; + pinctrl-names = "default"; + qcom,ath10k-calibration-variant = "GO_GALE"; +}; diff --git a/target/linux/ipq40xx/image/chromium.mk b/target/linux/ipq40xx/image/chromium.mk index 15d4c1a077e81..2c8457dcfbbb0 100644 --- a/target/linux/ipq40xx/image/chromium.mk +++ b/target/linux/ipq40xx/image/chromium.mk @@ -20,3 +20,17 @@ define Build/cros-vboot -k $@ -c "root=PARTUUID=%U/PARTNROFF=1" -o $@.new @mv $@.new $@ endef + +define Device/google_wifi + DEVICE_VENDOR := Google + DEVICE_MODEL := WiFi (Gale) + SOC := qcom-ipq4019 + KERNEL_SUFFIX := -fit-zImage.itb.vboot + KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb | cros-vboot + KERNEL_NAME := zImage + IMAGES += factory.bin + IMAGE/factory.bin := cros-gpt | append-kernel-part | append-rootfs + DEVICE_PACKAGES := ipq-wifi-google_wifi partx-utils mkf2fs e2fsprogs \ + kmod-fs-ext4 kmod-fs-f2fs kmod-google-firmware +endef +TARGET_DEVICES += google_wifi diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch index 38ac3058a3166..a6a082a2c8a93 100644 --- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -903,11 +903,75 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -903,11 +903,76 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -71,10 +71,11 @@ Signed-off-by: John Crispin + qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-srr60.dtb \ + qcom-ipq4019-srs60.dtb \ -+ qcom-ipq4019-x1pro.dtb \ + qcom-ipq4019-u4019-32m.dtb \ ++ qcom-ipq4019-wifi.dtb \ + qcom-ipq4019-wpj419.dtb \ + qcom-ipq4019-wtr-m2133hp.dtb \ ++ qcom-ipq4019-x1pro.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-ap-303.dtb \ + qcom-ipq4029-ap-303h.dtb \