There are currently two sets of tests in this directory:
- functional which test the functionality of obsrd and obsr-qt by interacting with them through the RPC and P2P interfaces.
- util which tests the obsr utilities, currently only obsr-tx.
The util tests are run as part of
make check target. The functional
tests are run by the travis continuous build process whenever a pull
request is opened. Both sets of tests can also be run locally.
Running tests locally
Build for your system first. Be sure to enable wallet, utils and daemon when you configure. Tests will not run otherwise.
The ZMQ functional test requires a python ZMQ library. To install it:
- on Unix, run
sudo apt-get install python3-zmq
- on mac OS, run
pip3 install pyzmq
Running the tests
Individual tests can be run by directly calling the test script, eg:
or can be run through the test_runner harness, eg:
You can run any combination (incl. duplicates) of tests by calling:
test/functional/test_runner.py <testname1> <testname2> <testname3> ...
Run the regression test suite with:
Run all possible tests with
By default, up to 4 tests will be run in parallel by test_runner. To specify
how many jobs to run, append
The individual tests and the test_runner harness have many command-line
test_runner.py -h to see them all.
Troubleshooting and debugging test failures
The P2P and RPC ports used by the obsrd nodes-under-test are chosen to make conflicts with other processes unlikely. However, if there is another obsrd process running on the system (perhaps from a previous test which hasn't successfully killed all its obsrd nodes), then there may be a port conflict which will cause the test to fail. It is recommended that you run the tests on a system where no other obsrd processes are running.
On linux, the test_framework will warn if there is another obsrd process running when the tests are started.
If there are zombie obsrd processes after test failure, you can kill them by running the following commands. Note that these commands will kill all obsrd processes running on the system, so should not be used if any non-test obsrd processes are being run.
pkill -9 obsrd
Data directory cache
A pre-mined blockchain with 200 blocks is generated the first time a functional test is run and is stored in test/cache. This speeds up test startup times since new blockchains don't need to be generated for each test. However, the cache may get into a bad state, in which case tests will fail. If this happens, remove the cache directory (and make sure obsrd processes are stopped as above):
rm -rf cache killall obsrd
The tests contain logging at different levels (debug, info, warning, etc). By default:
- when run through the test_runner harness, all logs are written to
test_framework.logand no logs are output to the console.
- when run directly, all logs are written to
test_framework.logand INFO level and above are output to the console.
- when run on Travis, no logs are output to the console. However, if a test
debug.logs will all be dumped to the console to help troubleshooting.
To change the level of logs output to the console, use the
-l command line
test_framework.log and obsrd
debug.logs can be combined into a single
aggregate log by running the
combine_logs.py script. The output can be plain
text, colorized text or html. For example:
combine_logs.py -c <test data directory> | less -r
will pipe the colorized logs from the test into less.
--tracerpc to trace out all the RPC calls and responses to the console. For
some tests (eg any that use
submitblock to submit a full block over RPC),
this can result in a lot of screen output.
By default, the test data directory will be deleted after a successful run.
--nocleanup to leave the test data directory intact. The test data
directory is never deleted after a failed test.
Attaching a debugger
A python debugger can be attached to tests at any point. Just add the line:
import pdb; pdb.set_trace()
anywhere in the test. You will then be able to inspect variables, as well as call methods that interact with the obsrd nodes-under-test.
If further introspection of the obsrd instances themselves becomes
necessary, this can be accomplished by first setting a pdb breakpoint
at an appropriate location, running the test to that point, then using
gdb to attach to the process and debug.
For instance, to attach to
self.node during a run:
2017-06-27 14:13:56.686000 TestFramework (INFO): Initializing test directory /tmp/user/1000/testo9vsdjo3
use the directory path to get the pid from the pid file:
cat /tmp/user/1000/testo9vsdjo3/node1/regtest/obsrd.pid gdb /home/example/obsrd <pid>
Note: gdb attach step may require
Util tests can be run locally by running
-v option for verbose output.
Writing functional tests
You are encouraged to write functional tests for new or existing features. Further information about the functional test framework and individual tests is found in test/functional.