U-Boot 2018.01-21439-gd244ce5 (Jul 29 2021 - 16:33:01 +0100), Build: jenkins-development-build_uboot-1 Model: Zynq Zed Development Board Board: Xilinx Zynq Silicon: v3.1 DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 (SD) SF: Detected n25q256a with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Importing environment from SD ... Hit any key to stop autoboot: 0 Device: sdhci@e0100000 Manufacturer ID: fe OEM: 3432 Name: SD16G Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 58.2 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes reading uEnv.txt 407 bytes read in 19 ms (20.5 KiB/s) Loaded environment from uEnv.txt Importing environment from SD ... Running uenvcmd ... Copying Linux from SD to RAM... reading uImage 5593704 bytes read in 321 ms (16.6 MiB/s) reading devicetree.dtb 19895 bytes read in 23 ms (844.7 KiB/s) ** Unable to read file uramdisk.image.gz ** ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-5.10.0-98248-g1bbe32fa5182 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5593640 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02a00000 Booting using the fdt blob at 0x2a00000 Loading Kernel Image ... OK Loading Device Tree to 1eb11000, end 1eb18db6 ... OK Starting kernel ... C:0x000080C0-0x0055DA40->0x010C9800-0x0161F180 Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.10.0-98248-g1bbe32fa5182-dirty (jxj@jxj-pc) (arm-xilinx-linux-gnueabi-gcc.real (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.0.20200730) #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Analog Devices ADRV9361-Z7035 (Z7035/AD9361) OF: fdt: earlycon: stdout-path /amba@0/uart@E0001000 not found Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x16800000 Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] percpu: Embedded 15 pages/cpu s29900 r8192 d23348 u61440 Built 1 zonelists, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlycon rootfstype=ext4 rootwait clk_ignore_unused cpuidle.off=1 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 371432K/524288K available (8192K kernel code, 803K rwdata, 5732K rodata, 1024K init, 151K bss, 21784K reserved, 131072K cma-reserved, 0K highmem) rcu: Preemptible hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Trampoline variant of Tasks RCU enabled. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to (ptrval) slcr mapped to (ptrval) L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 random: get_random_bytes called from start_kernel+0x33c/0x4dc with crng_init=0 zynq_clock_init: clkc starts at (ptrval) Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at (ptrval), irq=25 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: Spectre v2: using BPIALL workaround CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU1: Spectre v2: using BPIALL workaround smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0x(ptrval) e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 33, base_baud = 6249999) is a xuartps printk: console [ttyPS0] enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb mc: Linux media interface: v0.10 videodev: Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered jesd204: found 0 devices and 0 topologies FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=17 bucket_order=0 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler mq-deadline registered io scheduler kyber registered zynq-pinctrl 700.pinctrl: zynq pinctrl initialized dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded spi-nor spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 spi-nor spi1.0: found n25q256ax1, expected n25q256a spi-nor spi1.0: trying to lock already unlocked area spi-nor spi1.0: n25q256ax1 (32768 Kbytes) 6 fixed-partitions partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 36 (00:05:f7:80:1b:ab) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: supply vcc not found, using dummy regulator at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer with timeout 10s Xilinx Zynq CpuIdle Driver started failed to register cpuidle driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver ad7291: probe of 0-002f failed with error -5 mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA fpga_manager fpga0: Xilinx Zynq FPGA Manager registered xt_time: kernel timezone is -0000 ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully NET: Registered protocol family 17 Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates input: gpio_keys as /devices/soc0/gpio_keys/input/input0 mmc0: new high speed SDXC card at address 0001 mmcblk0: mmc0:0001 SD16G 58.2 GiB clk: Not disabling unused clocks ALSA device list: No soundcards found. mmcblk0: p1 p2 p3 EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K Run /sbin/init as init process random: fast init done systemd[1]: System time before build time, advancing clock. systemd[1]: Failed to look up module alias 'autofs4': Function not implemented systemd[1]: systemd 247.3-7+rpi1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) systemd[1]: Detected architecture arm. Welcome to Kuiper GNU/Linux 11.2 (bullseye)! systemd[1]: Set hostname to . systemd[1]: Binding to IPv6 address not available since kernel does not support IPv6. systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed. systemd[1]: Queued start job for default target Graphical Interface. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. systemd[1]: (This warning is only shown for the first unit using IP firewalling.) systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. systemd[1]: Condition check resulted in Journal Audit Socket being skipped. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Condition check resulted in Huge Pages File System being skipped. systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. systemd[1]: Mounting RPC Pipe File System... Mounting RPC Pipe File System... systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... systemd[1]: Condition check resulted in Kernel Trace File System being skipped. systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped. systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... systemd[1]: Starting Set the console keyboard layout... Starting Set the console keyboard layout... systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. systemd[1]: Condition check resulted in File System Check on Root Device being skipped. systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... systemd[1]: run-rpc_pipefs.mount: Mount process exited, code=exited, status=32/n/a systemd[1]: run-rpc_pipefs.mount: Failed with result 'exit-code'. systemd[1]: Failed to mount RPC Pipe File System. [FAILED] Failed to mount RPC Pipe File System. See 'systemctl status run-rpc_pipefs.mount' for details. systemd[1]: Dependency failed for RPC security service for NFS server. [DEPEND] Dependency failed for RPC …curity service for NFS server. systemd[1]: rpc-svcgssd.service: Job rpc-svcgssd.service/start failed with result 'dependency'. systemd[1]: Dependency failed for RPC security service for NFS client and server. [DEPEND] Dependency failed for RPC …ice for NFS client and server. systemd[1]: rpc-gssd.service: Job rpc-gssd.service/start failed with result 'dependency'. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. random: crng init done random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Mounted Kernel Debug File System. [ OK ] Finished Restore / save the current clock. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Mounting Kernel Configuration File System... EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Starting Apply Kernel Variables... [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Finished Set the console keyboard layout. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Create System Users... [ OK ] Finished Coldplug All udev Devices. Starting Helper to synchronize boot up for ifupdown... Starting Wait for udev To …plete Device Initialization... [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Show Plymouth Boot Screen... [ OK ] Started Show Plymouth Boot Screen. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Found device /dev/ttyPS0. [ OK ] Found device /dev/disk/by-partuuid/f7eeebee-01. Starting File System Check…isk/by-partuuid/f7eeebee-01... [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started File System Check Daemon to report status. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Finished File System Check…/disk/by-partuuid/f7eeebee-01. Mounting /boot... [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. Starting Set console font and keymap... Starting Raise network interfaces... Starting Preprocess NFS configuration... Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... [ OK ] Finished Set console font and keymap. [ OK ] Finished Preprocess NFS configuration. [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ OK ] Finished Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started CUPS Scheduler. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Paths. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on CUPS Scheduler. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on GPS (Global P…ioning System) Daemon Sockets. [ OK ] Listening on triggerhappy.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting dphys-swapfile - …unt, and delete a swap file... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting Creating IIOD Context Attributes...... Starting DHCP Client Daemon... Starting LSB: Switch to on…nless shift key is pressed)... Starting LSB: rng-tools (Debian variant)... Starting System Logging Service... Starting User Login Management... Starting triggerhappy global hotkey daemon... Starting Disk Manager... Starting WPA supplicant... [ OK ] Started System Logging Service. [ OK ] Started triggerhappy global hotkey daemon. [ OK ] Started DHCP Client Daemon. [ OK ] Started LSB: rng-tools (Debian variant). [ OK ] Finished dphys-swapfile - …mount, and delete a swap file. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started WPA supplicant. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. Starting Authorization Manager... [ OK ] Started Authorization Manager. [ OK ] Finished Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting CUPS Scheduler... Starting HTTP based time synchronization tool... Starting Internet superserver... Starting LSB: DHCP server... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... My IP address is 192.168.10.122 [ OK ] Started Unattended Upgrades Shutdown. Starting LSB: Webfs simple HTTP server... [ OK ] Started Internet superserver. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Finished Permit User Sessions. [ OK ] Started HTTP based time synchronization tool. Starting Light Display Manager... Starting Hold until boot process finishes up... [ OK ] Started LSB: Switch to ond…(unless shift key is pressed). [ OK ] Started LSB: Webfs simple HTTP server. [ OK ] Started CUPS Scheduler. [ OK ] Started Make remote CUPS printers available locally. [ OK ] Finished Creating IIOD Context Attributes.... [ OK ] Started IIO Daemon. [FAILED] Failed to start VNC Server for X11. [FAILED] Failed to start LSB: DHCP server. Raspbian GNU/Linux 11 analog ttyPS0 analog login: root (automatic login) Linux analog 5.10.0-98248-g1bbe32fa5182-dirty #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Thu Feb 9 10:44:55 GMT 2023 from 192.168.10.1 on pts/0 root@analog:~# U-Boot 2018.01-21439-gd244ce5 (Jul 29 2021 - 16:33:01 +0100), Build: jenkins-development-build_uboot-1 Model: Zynq Zed Development Board Board: Xilinx Zynq Silicon: v3.1 DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 (SD) SF: Detected n25q256a with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Importing environment from SD ... Hit any key to stop autoboot: 0 Device: sdhci@e0100000 Manufacturer ID: fe OEM: 3432 Name: SD16G Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 58.2 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Loaded environment from uEnv.txt Importing environment from SD ... Running uenvcmd ... Copying Linux from SD to RAM... reading uImage 5593704 bytes read in 322 ms (16.6 MiB/s) reading devicetree.dtb 19895 bytes read in 23 ms (844.7 KiB/s) ** Unable to read file uramdisk.image.gz ** ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-5.10.0-98248-g1bbe32fa5182 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5593640 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02a00000 Booting using the fdt blob at 0x2a00000 Loading Kernel Image ... OK Loading Device Tree to 1eb11000, end 1eb18db6 ... OK Starting kernel ... C:0x000080C0-0x0055DA40->0x010C9800-0x0161F180 Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.10.0-98248-g1bbe32fa5182-dirty (jxj@jxj-pc) (arm-xilinx-linux-gnueabi-gcc.real (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.0.20200730) #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Analog Devices ADRV9361-Z7035 (Z7035/AD9361) OF: fdt: earlycon: stdout-path /amba@0/uart@E0001000 not found Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x16800000 Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] percpu: Embedded 15 pages/cpu s29900 r8192 d23348 u61440 Built 1 zonelists, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlycon rootfstype=ext4 rootwait clk_ignore_unused cpuidle.off=1 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 371432K/524288K available (8192K kernel code, 803K rwdata, 5732K rodata, 1024K init, 151K bss, 21784K reserved, 131072K cma-reserved, 0K highmem) rcu: Preemptible hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Trampoline variant of Tasks RCU enabled. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to (ptrval) slcr mapped to (ptrval) L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 random: get_random_bytes called from start_kernel+0x33c/0x4dc with crng_init=0 zynq_clock_init: clkc starts at (ptrval) Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at (ptrval), irq=25 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: Spectre v2: using BPIALL workaround CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU1: Spectre v2: using BPIALL workaround smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0x(ptrval) e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 33, base_baud = 6249999) is a xuartps printk: console [ttyPS0] enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb mc: Linux media interface: v0.10 videodev: Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered jesd204: found 0 devices and 0 topologies FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=17 bucket_order=0 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler mq-deadline registered io scheduler kyber registered zynq-pinctrl 700.pinctrl: zynq pinctrl initialized dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded spi-nor spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 spi-nor spi1.0: found n25q256ax1, expected n25q256a spi-nor spi1.0: trying to lock already unlocked area spi-nor spi1.0: n25q256ax1 (32768 Kbytes) 6 fixed-partitions partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 36 (00:05:f7:80:1b:ab) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: supply vcc not found, using dummy regulator at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer with timeout 10s Xilinx Zynq CpuIdle Driver started failed to register cpuidle driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver ad7291: probe of 0-002f failed with error -5 mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA fpga_manager fpga0: Xilinx Zynq FPGA Manager registered xt_time: kernel timezone is -0000 ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully NET: Registered protocol family 17 Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates mmc0: new high speed SDXC card at address 0001 mmcblk0: mmc0:0001 SD16G 58.2 GiB input: gpio_keys as /devices/soc0/gpio_keys/input/input0 mmcblk0: p1 p2 p3 clk: Not disabling unused clocks ALSA device list: No soundcards found. random: fast init done EXT4-fs (mmcblk0p2): 1 orphan inode deleted EXT4-fs (mmcblk0p2): recovery complete EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K Run /sbin/init as init process systemd[1]: System time before build time, advancing clock. systemd[1]: Failed to look up module alias 'autofs4': Function not implemented systemd[1]: systemd 247.3-7+rpi1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) systemd[1]: Detected architecture arm. Welcome to Kuiper GNU/Linux 11.2 (bullseye)! systemd[1]: Set hostname to . systemd[1]: Binding to IPv6 address not available since kernel does not support IPv6. systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed. systemd[1]: Queued start job for default target Graphical Interface. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. systemd[1]: (This warning is only shown for the first unit using IP firewalling.) systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. systemd[1]: Condition check resulted in Journal Audit Socket being skipped. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Condition check resulted in Huge Pages File System being skipped. systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. systemd[1]: Mounting RPC Pipe File System... Mounting RPC Pipe File System... systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... systemd[1]: Condition check resulted in Kernel Trace File System being skipped. systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped. systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... systemd[1]: Starting Set the console keyboard layout... Starting Set the console keyboard layout... systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. systemd[1]: Condition check resulted in File System Check on Root Device being skipped. systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... systemd[1]: run-rpc_pipefs.mount: Mount process exited, code=exited, status=32/n/a systemd[1]: run-rpc_pipefs.mount: Failed with result 'exit-code'. systemd[1]: Failed to mount RPC Pipe File System. [FAILED] Failed to mount RPC Pipe File System. See 'systemctl status run-rpc_pipefs.mount' for details. systemd[1]: Dependency failed for RPC security service for NFS server. [DEPEND] Dependency failed for RPC …curity service for NFS server. systemd[1]: rpc-svcgssd.service: Job rpc-svcgssd.service/start failed with result 'dependency'. systemd[1]: Dependency failed for RPC security service for NFS client and server. [DEPEND] Dependency failed for RPC …ice for NFS client and server. systemd[1]: rpc-gssd.service: Job rpc-gssd.service/start failed with result 'dependency'. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. random: crng init done random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Mounted Kernel Debug File System. [ OK ] Finished Restore / save the current clock. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Pre). [ OK ] Reached target Remote File Systems. Mounting Kernel Configuration File System... Starting Apply Kernel Variables... [ OK ] Finished Set the console keyboard layout. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Apply Kernel Variables. Starting Helper to synchronize boot up for ifupdown... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Create System Users... Starting Wait for udev To …plete Device Initialization... [ OK ] Finished Create System Users. [ OK ] Finished Load/Save Random Seed. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Show Plymouth Boot Screen... [ OK ] Started Show Plymouth Boot Screen. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Found device /dev/ttyPS0. [ OK ] Found device /dev/disk/by-partuuid/f7eeebee-01. Starting File System Check…isk/by-partuuid/f7eeebee-01... [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started File System Check Daemon to report status. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Finished File System Check…/disk/by-partuuid/f7eeebee-01. Mounting /boot... [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. Starting Set console font and keymap... Starting Raise network interfaces... Starting Preprocess NFS configuration... Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... [ OK ] Finished Set console font and keymap. [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ OK ] Finished Preprocess NFS configuration. [ OK ] Finished Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started CUPS Scheduler. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Paths. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on CUPS Scheduler. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on GPS (Global P…ioning System) Daemon Sockets. [ OK ] Listening on triggerhappy.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting dphys-swapfile - …unt, and delete a swap file... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting Creating IIOD Context Attributes...... Starting DHCP Client Daemon... Starting LSB: Switch to on…nless shift key is pressed)... Starting LSB: rng-tools (Debian variant)... Starting System Logging Service... Starting User Login Management... Starting triggerhappy global hotkey daemon... Starting Disk Manager... Starting WPA supplicant... [ OK ] Started System Logging Service. [ OK ] Started triggerhappy global hotkey daemon. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started DHCP Client Daemon. [ OK ] Started WPA supplicant. [ OK ] Finished dphys-swapfile - …mount, and delete a swap file. [ OK ] Started LSB: rng-tools (Debian variant). [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. Starting Authorization Manager... [ OK ] Finished Raise network interfaces. [ OK ] Started Authorization Manager. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting CUPS Scheduler... Starting HTTP based time synchronization tool... Starting Internet superserver... Starting LSB: DHCP server... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... My IP address is 192.168.10.122 Starting Permit User Sessions... [ OK ] Started Unattended Upgrades Shutdown. Starting LSB: Webfs simple HTTP server... [ OK ] Started Internet superserver. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Finished Permit User Sessions. [ OK ] Started HTTP based time synchronization tool. Starting Light Display Manager... Starting Hold until boot process finishes up... [ OK ] Started LSB: Switch to ond…(unless shift key is pressed). [ OK ] Started CUPS Scheduler. [ OK ] Started Make remote CUPS printers available locally. [ OK ] Started LSB: Webfs simple HTTP server. [FAILED] Failed to start VNC Server for X11. [FAILED] Failed to start LSB: DHCP server. Raspbian GNU/Linux 11 analog ttyPS0 analog login: root (automatic login) Linux analog 5.10.0-98248-g1bbe32fa5182-dirty #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Thu Feb 9 10:45:27 GMT 2023 on ttyPS0 root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# ls kernel_modules32 openwifi openwifi64 kernel_modules64 openwifi32 openwifi_BOOT root@analog:~# df Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 13152080 6977604 5523244 56% / devtmpfs 185716 0 185716 0% /dev tmpfs 251764 0 251764 0% /dev/shm tmpfs 100708 600 100108 1% /run tmpfs 5120 0 5120 0% /run/lock /dev/mmcblk0p1 2093040 1251760 841280 60% /boot tmpfs 50352 16 50336 1% /run/user/1000 tmpfs 50352 20 50332 1% /run/user/0 root@analog:~# / -bash: /: Is a directory root@analog:~# U-Boot 2018.01-21439-gd244ce5 (Jul 29 2021 - 16:33:01 +0100), Build: jenkins-development-build_uboot-1 Model: Zynq Zed Development Board Board: Xilinx Zynq Silicon: v3.1 DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 (SD) SF: Detected n25q256a with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Importing environment from SD ... Hit any key to stop autoboot: 0 Device: sdhci@e0100000 Manufacturer ID: fe OEM: 3432 Name: SD16G Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 58.2 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Loaded environment from uEnv.txt Importing environment from SD ... Running uenvcmd ... Copying Linux from SD to RAM... reading uImage 5593704 bytes read in 322 ms (16.6 MiB/s) reading devicetree.dtb 19895 bytes read in 24 ms (808.6 KiB/s) ** Unable to read file uramdisk.image.gz ** ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-5.10.0-98248-g1bbe32fa5182 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5593640 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02a00000 Booting using the fdt blob at 0x2a00000 Loading Kernel Image ... OK Loading Device Tree to 1eb11000, end 1eb18db6 ... OK Starting kernel ... C:0x000080C0-0x0055DA40->0x010C9800-0x0161F180 Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.10.0-98248-g1bbe32fa5182-dirty (jxj@jxj-pc) (arm-xilinx-linux-gnueabi-gcc.real (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.0.20200730) #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Analog Devices ADRV9361-Z7035 (Z7035/AD9361) OF: fdt: earlycon: stdout-path /amba@0/uart@E0001000 not found Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x16800000 Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] percpu: Embedded 15 pages/cpu s29900 r8192 d23348 u61440 Built 1 zonelists, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlycon rootfstype=ext4 rootwait clk_ignore_unused cpuidle.off=1 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 371432K/524288K available (8192K kernel code, 803K rwdata, 5732K rodata, 1024K init, 151K bss, 21784K reserved, 131072K cma-reserved, 0K highmem) rcu: Preemptible hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Trampoline variant of Tasks RCU enabled. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to (ptrval) slcr mapped to (ptrval) L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 random: get_random_bytes called from start_kernel+0x33c/0x4dc with crng_init=0 zynq_clock_init: clkc starts at (ptrval) Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at (ptrval), irq=25 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: Spectre v2: using BPIALL workaround CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU1: Spectre v2: using BPIALL workaround smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0x(ptrval) e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 33, base_baud = 6249999) is a xuartps printk: console [ttyPS0] enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb mc: Linux media interface: v0.10 videodev: Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered jesd204: found 0 devices and 0 topologies FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=17 bucket_order=0 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler mq-deadline registered io scheduler kyber registered zynq-pinctrl 700.pinctrl: zynq pinctrl initialized dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded spi-nor spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 spi-nor spi1.0: found n25q256ax1, expected n25q256a spi-nor spi1.0: trying to lock already unlocked area spi-nor spi1.0: n25q256ax1 (32768 Kbytes) 6 fixed-partitions partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 36 (00:05:f7:80:1b:ab) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: supply vcc not found, using dummy regulator at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer with timeout 10s Xilinx Zynq CpuIdle Driver started failed to register cpuidle driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver ad7291: probe of 0-002f failed with error -5 mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA fpga_manager fpga0: Xilinx Zynq FPGA Manager registered xt_time: kernel timezone is -0000 ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully NET: Registered protocol family 17 Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates input: gpio_keys as /devices/soc0/gpio_keys/input/input0 clk: Not disabling unused clocks ALSA device list: No soundcards found. Waiting for root device /dev/mmcblk0p2... mmc0: new high speed SDXC card at address 0001 mmcblk0: mmc0:0001 SD16G 58.2 GiB mmcblk0: p1 p2 p3 random: fast init done EXT4-fs (mmcblk0p2): recovery complete EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K Run /sbin/init as init process systemd[1]: System time before build time, advancing clock. systemd[1]: Failed to look up module alias 'autofs4': Function not implemented systemd[1]: systemd 247.3-7+rpi1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) systemd[1]: Detected architecture arm. Welcome to Kuiper GNU/Linux 11.2 (bullseye)! systemd[1]: Set hostname to . systemd[1]: Binding to IPv6 address not available since kernel does not support IPv6. systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed. systemd[1]: Queued start job for default target Graphical Interface. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. systemd[1]: (This warning is only shown for the first unit using IP firewalling.) systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. systemd[1]: Condition check resulted in Journal Audit Socket being skipped. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Condition check resulted in Huge Pages File System being skipped. systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. systemd[1]: Mounting RPC Pipe File System... Mounting RPC Pipe File System... systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... systemd[1]: Condition check resulted in Kernel Trace File System being skipped. systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped. systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... systemd[1]: Starting Set the console keyboard layout... Starting Set the console keyboard layout... systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. systemd[1]: Condition check resulted in File System Check on Root Device being skipped. systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... systemd[1]: run-rpc_pipefs.mount: Mount process exited, code=exited, status=32/n/a systemd[1]: run-rpc_pipefs.mount: Failed with result 'exit-code'. systemd[1]: Failed to mount RPC Pipe File System. [FAILED] Failed to mount RPC Pipe File System. See 'systemctl status run-rpc_pipefs.mount' for details. systemd[1]: Dependency failed for RPC security service for NFS client and server. [DEPEND] Dependency failed for RPC …ice for NFS client and server. systemd[1]: rpc-gssd.service: Job rpc-gssd.service/start failed with result 'dependency'. systemd[1]: Dependency failed for RPC security service for NFS server. [DEPEND] Dependency failed for RPC …curity service for NFS server. systemd[1]: rpc-svcgssd.service: Job rpc-svcgssd.service/start failed with result 'dependency'. random: crng init done random: 7 urandom warning(s) missed due to ratelimiting systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted Kernel Debug File System. [ OK ] Finished Restore / save the current clock. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. XT4-fs (mmcblk0p2): re-mounted. Opts: (null) 0m. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Mounting Kernel Configuration File System... Starting Apply Kernel Variables... [ OK ] Finished Set the console keyboard layout. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Apply Kernel Variables. Starting Helper to synchronize boot up for ifupdown... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Create System Users... Starting Wait for udev To …plete Device Initialization... [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Show Plymouth Boot Screen... [ OK ] Started Show Plymouth Boot Screen. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Found device /dev/ttyPS0. [ OK ] Found device /dev/disk/by-partuuid/f7eeebee-01. [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting File System Check…isk/by-partuuid/f7eeebee-01... [ OK ] Started File System Check Daemon to report status. [ OK ] Finished File System Check…/disk/by-partuuid/f7eeebee-01. Mounting /boot... [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. Starting Set console font and keymap... Starting Raise network interfaces... Starting Preprocess NFS configuration... Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... [ OK ] Finished Set console font and keymap. [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ OK ] Finished Preprocess NFS configuration. [ OK ] Finished Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started CUPS Scheduler. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Paths. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on CUPS Scheduler. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on GPS (Global P…ioning System) Daemon Sockets. [ OK ] Listening on triggerhappy.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting dphys-swapfile - …unt, and delete a swap file... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting Creating IIOD Context Attributes...... Starting DHCP Client Daemon... Starting LSB: Switch to on…nless shift key is pressed)... Starting LSB: rng-tools (Debian variant)... Starting System Logging Service... Starting User Login Management... Starting triggerhappy global hotkey daemon... Starting Disk Manager... Starting WPA supplicant... [ OK ] Started triggerhappy global hotkey daemon. [ OK ] Started System Logging Service. [ OK ] Started DHCP Client Daemon. [ OK ] Finished dphys-swapfile - …mount, and delete a swap file. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started WPA supplicant. [ OK ] Started User Login Management. [ OK ] Started LSB: rng-tools (Debian variant). Starting Authorization Manager... [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Authorization Manager. [ OK ] Finished Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting CUPS Scheduler... Starting HTTP based time synchronization tool... Starting Internet superserver... Starting LSB: DHCP server... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... My IP address is 192.168.10.122 [ OK ] Started Unattended Upgrades Shutdown. Starting LSB: Webfs simple HTTP server... [ OK ] Started Internet superserver. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Finished Permit User Sessions. [ OK ] Started HTTP based time synchronization tool. Starting Light Display Manager... Starting Hold until boot process finishes up... [ OK ] Started LSB: Switch to ond…(unless shift key is pressed). [ OK ] Started LSB: Webfs simple HTTP server. [ OK ] Finished Creating IIOD Context Attributes.... [ OK ] Started IIO Daemon. [ OK ] Started CUPS Scheduler. [ OK ] Started Make remote CUPS printers available locally. [FAILED] Failed to start VNC Server for X11. [FAILED] Failed to start LSB: DHCP server. Raspbian GNU/Linux 11 analog ttyPS0 analog login: root (automatic login) Linux analog 5.10.0-98248-g1bbe32fa5182-dirty #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Thu Feb 9 10:45:27 GMT 2023 on ttyPS0 root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# ls kernel_modules32 openwifi openwifi64 kernel_modules64 openwifi32 openwifi_BOOT root@analog:~# U-Boot 2018.01-21439-gd244ce5 (Jul 29 2021 - 16:33:01 +0100), Build: jenkins-development-build_uboot-1 Model: Zynq Zed Development Board Board: Xilinx Zynq Silicon: v3.1 DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 (SD) SF: Detected n25q256a with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Importing environment from SD ... Hit any key to stop autoboot: 2 U-Boot 2018.01-21439-gd244ce5 (Jul 29 2021 - 16:33:01 +0100), Build: jenkins-development-build_uboot-1 Model: Zynq Zed Development Board Board: Xilinx Zynq Silicon: v3.1 DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 (SD) SF: Detected n25q256a with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Importing environment from SD ... Hit any key to stop autoboot: 0 Device: sdhci@e0100000 Manufacturer ID: fe OEM: 3432 Name: SD16G Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 58.2 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Loaded environment from uEnv.txt Importing environment from SD ... Running uenvcmd ... Copying Linux from SD to RAM... reading uImage 5593704 bytes read in 322 ms (16.6 MiB/s) reading devicetree.dtb 19895 bytes read in 24 ms (808.6 KiB/s) ** Unable to read file uramdisk.image.gz ** ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-5.10.0-98248-g1bbe32fa5182 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5593640 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02a00000 Booting using the fdt blob at 0x2a00000 Loading Kernel Image ... OK Loading Device Tree to 1eb11000, end 1eb18db6 ... OK Starting kernel ... C:0x000080C0-0x0055DA40->0x010C9800-0x0161F180 Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.10.0-98248-g1bbe32fa5182-dirty (jxj@jxj-pc) (arm-xilinx-linux-gnueabi-gcc.real (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.0.20200730) #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Analog Devices ADRV9361-Z7035 (Z7035/AD9361) OF: fdt: earlycon: stdout-path /amba@0/uart@E0001000 not found Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x16800000 Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] percpu: Embedded 15 pages/cpu s29900 r8192 d23348 u61440 Built 1 zonelists, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlycon rootfstype=ext4 rootwait clk_ignore_unused cpuidle.off=1 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 371432K/524288K available (8192K kernel code, 803K rwdata, 5732K rodata, 1024K init, 151K bss, 21784K reserved, 131072K cma-reserved, 0K highmem) rcu: Preemptible hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Trampoline variant of Tasks RCU enabled. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to (ptrval) slcr mapped to (ptrval) L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 random: get_random_bytes called from start_kernel+0x33c/0x4dc with crng_init=0 zynq_clock_init: clkc starts at (ptrval) Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at (ptrval), irq=25 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: Spectre v2: using BPIALL workaround CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU1: Spectre v2: using BPIALL workaround smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0x(ptrval) e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 33, base_baud = 6249999) is a xuartps printk: console [ttyPS0] enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb mc: Linux media interface: v0.10 videodev: Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered jesd204: found 0 devices and 0 topologies FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=17 bucket_order=0 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler mq-deadline registered io scheduler kyber registered zynq-pinctrl 700.pinctrl: zynq pinctrl initialized dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded spi-nor spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 spi-nor spi1.0: found n25q256ax1, expected n25q256a spi-nor spi1.0: trying to lock already unlocked area spi-nor spi1.0: n25q256ax1 (32768 Kbytes) 6 fixed-partitions partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 36 (00:05:f7:80:1b:ab) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: supply vcc not found, using dummy regulator at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer with timeout 10s Xilinx Zynq CpuIdle Driver started failed to register cpuidle driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver ad7291: probe of 0-002f failed with error -5 mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA fpga_manager fpga0: Xilinx Zynq FPGA Manager registered xt_time: kernel timezone is -0000 ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully NET: Registered protocol family 17 Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates mmc0: new high speed SDXC card at address 0001 mmcblk0: mmc0:0001 SD16G 58.2 GiB input: gpio_keys as /devices/soc0/gpio_keys/input/input0 mmcblk0: p1 p2 p3 clk: Not disabling unused clocks ALSA device list: No soundcards found. random: fast init done EXT4-fs (mmcblk0p2): 1 orphan inode deleted EXT4-fs (mmcblk0p2): recovery complete EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K Run /sbin/init as init process systemd[1]: System time before build time, advancing clock. systemd[1]: Failed to look up module alias 'autofs4': Function not implemented systemd[1]: systemd 247.3-7+rpi1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) systemd[1]: Detected architecture arm. Welcome to Kuiper GNU/Linux 11.2 (bullseye)! systemd[1]: Set hostname to . systemd[1]: Binding to IPv6 address not available since kernel does not support IPv6. systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed. systemd[1]: Queued start job for default target Graphical Interface. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. systemd[1]: (This warning is only shown for the first unit using IP firewalling.) systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. systemd[1]: Condition check resulted in Journal Audit Socket being skipped. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Condition check resulted in Huge Pages File System being skipped. systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. systemd[1]: Mounting RPC Pipe File System... Mounting RPC Pipe File System... systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... systemd[1]: Condition check resulted in Kernel Trace File System being skipped. systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped. systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... systemd[1]: Starting Set the console keyboard layout... Starting Set the console keyboard layout... systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. systemd[1]: Condition check resulted in File System Check on Root Device being skipped. systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... systemd[1]: run-rpc_pipefs.mount: Mount process exited, code=exited, status=32/n/a systemd[1]: run-rpc_pipefs.mount: Failed with result 'exit-code'. systemd[1]: Failed to mount RPC Pipe File System. [FAILED] Failed to mount RPC Pipe File System. See 'systemctl status run-rpc_pipefs.mount' for details. systemd[1]: Dependency failed for RPC security service for NFS client and server. [DEPEND] Dependency failed for RPC …ice for NFS client and server. systemd[1]: rpc-gssd.service: Job rpc-gssd.service/start failed with result 'dependency'. systemd[1]: Dependency failed for RPC security service for NFS server. [DEPEND] Dependency failed for RPC …curity service for NFS server. systemd[1]: rpc-svcgssd.service: Job rpc-svcgssd.service/start failed with result 'dependency'. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. random: crng init done random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Mounted Kernel Debug File System. [ OK ] Finished Restore / save the current clock. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Mounting Kernel Configuration File System... Starting Apply Kernel Variables... [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Set the console keyboard layout. Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Create System Users... [ OK ] Finished Coldplug All udev Devices. Starting Helper to synchronize boot up for ifupdown... Starting Wait for udev To …plete Device Initialization... [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Show Plymouth Boot Screen... [ OK ] Started Show Plymouth Boot Screen. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Found device /dev/ttyPS0. [ OK ] Found device /dev/disk/by-partuuid/f7eeebee-01. [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting File System Check…isk/by-partuuid/f7eeebee-01... [ OK ] Started File System Check Daemon to report status. [ OK ] Finished File System Check…/disk/by-partuuid/f7eeebee-01. Mounting /boot... [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. Starting Set console font and keymap... Starting Raise network interfaces... Starting Preprocess NFS configuration... Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... [ OK ] Finished Set console font and keymap. [ OK ] Finished Preprocess NFS configuration. [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ OK ] Finished Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started CUPS Scheduler. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Paths. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on CUPS Scheduler. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on GPS (Global P…ioning System) Daemon Sockets. [ OK ] Listening on triggerhappy.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting dphys-swapfile - …unt, and delete a swap file... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting Creating IIOD Context Attributes...... Starting DHCP Client Daemon... Starting LSB: Switch to on…nless shift key is pressed)... Starting LSB: rng-tools (Debian variant)... Starting System Logging Service... Starting User Login Management... Starting triggerhappy global hotkey daemon... Starting Disk Manager... Starting WPA supplicant... [ OK ] Started triggerhappy global hotkey daemon. [ OK ] Started System Logging Service. [ OK ] Started DHCP Client Daemon. [ OK ] Finished dphys-swapfile - …mount, and delete a swap file. [ OK ] Started LSB: rng-tools (Debian variant). [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started WPA supplicant. [ OK ] Started User Login Management. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. Starting Authorization Manager... [ OK ] Started Authorization Manager. [ OK ] Finished Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting CUPS Scheduler... Starting HTTP based time synchronization tool... Starting Internet superserver... Starting LSB: DHCP server... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... [ OK ] Started Unattended Upgrades Shutdown. My IP address is 192.168.10.122 Starting LSB: Webfs simple HTTP server... [ OK ] Started Internet superserver. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Finished Permit User Sessions. [ OK ] Started HTTP based time synchronization tool. [ OK ] Started LSB: Switch to ond…(unless shift key is pressed). Starting Light Display Manager... Starting Hold until boot process finishes up... [ OK ] Started CUPS Scheduler. [ OK ] Started Make remote CUPS printers available locally. [ OK ] Finished Creating IIOD Context Attributes.... [ OK ] Started IIO Daemon. [ OK ] Started LSB: Webfs simple HTTP server. [ OK ] Started Disk Manager. [FAILED] Failed to start VNC Server for X11. [FAILED] Failed to start LSB: DHCP server. Raspbian GNU/Linux 11 analog ttyPS0 analog login: root (automatic login) Linux analog 5.10.0-98248-g1bbe32fa5182-dirty #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Thu Feb 9 10:45:27 GMT 2023 on ttyPS0 root@analog:~# U-Boot 2018.01-21439-gd244ce5 (Jul 29 2021 - 16:33:01 +0100), Build: jenkins-development-build_uboot-1 Model: Zynq Zed Development Board Board: Xilinx Zynq Silicon: v3.1 DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 (SD) SF: Detected n25q256a with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Importing environment from SD ... Hit any key to stop autoboot: 0 Device: sdhci@e0100000 Manufacturer ID: fe OEM: 3432 Name: SD16G Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 58.2 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Loaded environment from uEnv.txt Importing environment from SD ... Running uenvcmd ... Copying Linux from SD to RAM... reading uImage 5593704 bytes read in 322 ms (16.6 MiB/s) reading devicetree.dtb 19895 bytes read in 24 ms (808.6 KiB/s) ** Unable to read file uramdisk.image.gz ** ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-5.10.0-98248-g1bbe32fa5182 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5593640 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02a00000 Booting using the fdt blob at 0x2a00000 Loading Kernel Image ... OK Loading Device Tree to 1eb11000, end 1eb18db6 ... OK Starting kernel ... C:0x000080C0-0x0055DA40->0x010C9800-0x0161F180 Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.10.0-98248-g1bbe32fa5182-dirty (jxj@jxj-pc) (arm-xilinx-linux-gnueabi-gcc.real (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.0.20200730) #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Analog Devices ADRV9361-Z7035 (Z7035/AD9361) OF: fdt: earlycon: stdout-path /amba@0/uart@E0001000 not found Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x16800000 Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] percpu: Embedded 15 pages/cpu s29900 r8192 d23348 u61440 Built 1 zonelists, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlycon rootfstype=ext4 rootwait clk_ignore_unused cpuidle.off=1 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 371432K/524288K available (8192K kernel code, 803K rwdata, 5732K rodata, 1024K init, 151K bss, 21784K reserved, 131072K cma-reserved, 0K highmem) rcu: Preemptible hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Trampoline variant of Tasks RCU enabled. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to (ptrval) slcr mapped to (ptrval) L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 random: get_random_bytes called from start_kernel+0x33c/0x4dc with crng_init=0 zynq_clock_init: clkc starts at (ptrval) Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at (ptrval), irq=25 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: Spectre v2: using BPIALL workaround CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU1: Spectre v2: using BPIALL workaround smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0x(ptrval) e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 33, base_baud = 6249999) is a xuartps printk: console [ttyPS0] enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb mc: Linux media interface: v0.10 videodev: Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered jesd204: found 0 devices and 0 topologies FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=17 bucket_order=0 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler mq-deadline registered io scheduler kyber registered zynq-pinctrl 700.pinctrl: zynq pinctrl initialized dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded spi-nor spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 spi-nor spi1.0: found n25q256ax1, expected n25q256a spi-nor spi1.0: trying to lock already unlocked area spi-nor spi1.0: n25q256ax1 (32768 Kbytes) 6 fixed-partitions partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 36 (00:05:f7:80:1b:ab) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: supply vcc not found, using dummy regulator at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer with timeout 10s Xilinx Zynq CpuIdle Driver started failed to register cpuidle driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver ad7291: probe of 0-002f failed with error -5 mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA fpga_manager fpga0: Xilinx Zynq FPGA Manager registered xt_time: kernel timezone is -0000 ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully NET: Registered protocol family 17 Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates mmc0: new high speed SDXC card at address 0001 mmcblk0: mmc0:0001 SD16G 58.2 GiB input: gpio_keys as /devices/soc0/gpio_keys/input/input0 mmcblk0: p1 p2 p3 clk: Not disabling unused clocks ALSA device list: No soundcards found. random: fast init done EXT4-fs (mmcblk0p2): recovery complete EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K Run /sbin/init as init process systemd[1]: System time before build time, advancing clock. systemd[1]: Failed to look up module alias 'autofs4': Function not implemented systemd[1]: systemd 247.3-7+rpi1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) systemd[1]: Detected architecture arm. Welcome to Kuiper GNU/Linux 11.2 (bullseye)! systemd[1]: Set hostname to . systemd[1]: Binding to IPv6 address not available since kernel does not support IPv6. systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed. systemd[1]: Queued start job for default target Graphical Interface. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. systemd[1]: (This warning is only shown for the first unit using IP firewalling.) systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. systemd[1]: Condition check resulted in Journal Audit Socket being skipped. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Condition check resulted in Huge Pages File System being skipped. systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. systemd[1]: Mounting RPC Pipe File System... Mounting RPC Pipe File System... systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... systemd[1]: Condition check resulted in Kernel Trace File System being skipped. systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped. systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... systemd[1]: Starting Set the console keyboard layout... Starting Set the console keyboard layout... systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. systemd[1]: Condition check resulted in File System Check on Root Device being skipped. systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... systemd[1]: run-rpc_pipefs.mount: Mount process exited, code=exited, status=32/n/a systemd[1]: run-rpc_pipefs.mount: Failed with result 'exit-code'. systemd[1]: Failed to mount RPC Pipe File System. [FAILED] Failed to mount RPC Pipe File System. See 'systemctl status run-rpc_pipefs.mount' for details. systemd[1]: Dependency failed for RPC security service for NFS server. [DEPEND] Dependency failed for RPC …curity service for NFS server. systemd[1]: rpc-svcgssd.service: Job rpc-svcgssd.service/start failed with result 'dependency'. systemd[1]: Dependency failed for RPC security service for NFS client and server. random: crng init done random: 7 urandom warning(s) missed due to ratelimiting [DEPEND] Dependency failed for RPC …ice for NFS client and server. systemd[1]: rpc-gssd.service: Job rpc-gssd.service/start failed with result 'dependency'. systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. systemd[1]: Finished Restore / save the current clock. [ OK ] Finished Restore / save the current clock. systemd[1]: modprobe@configfs.service: Succeeded. systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [FAILED] Failed to start Load Kernel Modules. EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) See 'systemctl status systemd-modules-load.service' for details. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Finished Set the console keyboard layout. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... systemd-journald[1090]: Received client request to flush runtime journal. Starting Create System Users... systemd-journald[1090]: File /var/log/journal/9a314adf4f7b4c659ada5035385c9b39/system.journal corrupted or uncleanly shut down, renaming and replacing. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Coldplug All udev Devices. Starting Helper to synchronize boot up for ifupdown... Starting Wait for udev To …plete Device Initialization... [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Show Plymouth Boot Screen... [ OK ] Started Show Plymouth Boot Screen. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Found device /dev/ttyPS0. [ OK ] Found device /dev/disk/by-partuuid/f7eeebee-01. [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting File System Check…isk/by-partuuid/f7eeebee-01... [ OK ] Started File System Check Daemon to report status. [ OK ] Finished File System Check…/disk/by-partuuid/f7eeebee-01. Mounting /boot... [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. Starting Set console font and keymap... Starting Raise network interfaces... Starting Preprocess NFS configuration... Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... [ OK ] Finished Preprocess NFS configuration. [ OK ] Finished Set console font and keymap. [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ OK ] Finished Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started CUPS Scheduler. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Paths. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on CUPS Scheduler. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on GPS (Global P…ioning System) Daemon Sockets. [ OK ] Listening on triggerhappy.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting dphys-swapfile - …unt, and delete a swap file... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting Creating IIOD Context Attributes...... Starting DHCP Client Daemon... Starting LSB: Switch to on…nless shift key is pressed)... Starting LSB: rng-tools (Debian variant)... Starting System Logging Service... Starting User Login Management... Starting triggerhappy global hotkey daemon... Starting Disk Manager... Starting WPA supplicant... [ OK ] Started System Logging Service. [ OK ] Started triggerhappy global hotkey daemon. [ OK ] Started DHCP Client Daemon. [ OK ] Finished dphys-swapfile - …mount, and delete a swap file. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started LSB: rng-tools (Debian variant). [ OK ] Started WPA supplicant. Starting Authorization Manager... [ OK ] Started User Login Management. [ OK ] Started Authorization Manager. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Finished Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting CUPS Scheduler... Starting HTTP based time synchronization tool... Starting Internet superserver... Starting LSB: DHCP server... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... My IP address is 192.168.10.122 [ OK ] Started Unattended Upgrades Shutdown. Starting LSB: Webfs simple HTTP server... [ OK ] Started Internet superserver. [ OK ] Started HTTP based time synchronization tool. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Finished Permit User Sessions. Starting Light Display Manager... Starting Hold until boot process finishes up... [ OK ] Started LSB: Switch to ond…(unless shift key is pressed). [ OK ] Started CUPS Scheduler. [ OK ] Started Make remote CUPS printers available locally. [ OK ] Started LSB: Webfs simple HTTP server. [ OK ] Started Disk Manager. [ OK ] Finished Creating IIOD Context Attributes.... [ OK ] Started IIO Daemon. [FAILED] Failed to start VNC Server for X11. [FAILED] Failed to start LSB: DHCP server. Raspbian GNU/Linux 11 analog ttyPS0 analog login: root (automatic login) Linux analog 5.10.0-98248-g1bbe32fa5182-dirty #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Thu Feb 9 10:45:27 GMT 2023 on ttyPS0 root@analog:~# U-Boot 2018.01-21439-gd244ce5 (Jul 29 2021 - 16:33:01 +0100), Build: jenkins-development-build_uboot-1 Model: Zynq Zed Development Board Board: Xilinx Zynq Silicon: v3.1 DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 (SD) SF: Detected n25q256a with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Importing environment from SD ... Hit any key to stop autoboot: 0 Device: sdhci@e0100000 Manufacturer ID: fe OEM: 3432 Name: SD16G Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 58.2 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Loaded environment from uEnv.txt Importing environment from SD ... Running uenvcmd ... Copying Linux from SD to RAM... reading uImage 5593704 bytes read in 322 ms (16.6 MiB/s) reading devicetree.dtb 19895 bytes read in 24 ms (808.6 KiB/s) ** Unable to read file uramdisk.image.gz ** ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-5.10.0-98248-g1bbe32fa5182 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5593640 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02a00000 Booting using the fdt blob at 0x2a00000 Loading Kernel Image ... OK Loading Device Tree to 1eb11000, end 1eb18db6 ... OK Starting kernel ... C:0x000080C0-0x0055DA40->0x010C9800-0x0161F180 Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.10.0-98248-g1bbe32fa5182-dirty (jxj@jxj-pc) (arm-xilinx-linux-gnueabi-gcc.real (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.0.20200730) #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Analog Devices ADRV9361-Z7035 (Z7035/AD9361) OF: fdt: earlycon: stdout-path /amba@0/uart@E0001000 not found Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x16800000 Zone ranges: Normal [mem 0x0000000000000000-0x000000001fffffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x000000001fffffff] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] percpu: Embedded 15 pages/cpu s29900 r8192 d23348 u61440 Built 1 zonelists, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlycon rootfstype=ext4 rootwait clk_ignore_unused cpuidle.off=1 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 371432K/524288K available (8192K kernel code, 803K rwdata, 5732K rodata, 1024K init, 151K bss, 21784K reserved, 131072K cma-reserved, 0K highmem) rcu: Preemptible hierarchical RCU implementation. rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Trampoline variant of Tasks RCU enabled. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to (ptrval) slcr mapped to (ptrval) L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 random: get_random_bytes called from start_kernel+0x33c/0x4dc with crng_init=0 zynq_clock_init: clkc starts at (ptrval) Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at (ptrval), irq=25 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok CPU0: Spectre v2: using BPIALL workaround CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 rcu: Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU1: Spectre v2: using BPIALL workaround smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes, linear) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations thermal_sys: Registered thermal governor 'step_wise' hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0x(ptrval) e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 33, base_baud = 6249999) is a xuartps printk: console [ttyPS0] enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb mc: Linux media interface: v0.10 videodev: Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered jesd204: found 0 devices and 0 topologies FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes, linear) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=17 bucket_order=0 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler mq-deadline registered io scheduler kyber registered zynq-pinctrl 700.pinctrl: zynq pinctrl initialized dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded spi-nor spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 spi-nor spi1.0: found n25q256ax1, expected n25q256a spi-nor spi1.0: trying to lock already unlocked area spi-nor spi1.0: n25q256ax1 (32768 Kbytes) 6 fixed-partitions partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 36 (00:05:f7:80:1b:ab) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: supply vcc not found, using dummy regulator at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer with timeout 10s Xilinx Zynq CpuIdle Driver started failed to register cpuidle driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs hid: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA ad7291: probe of 0-002f failed with error -5 fpga_manager fpga0: Xilinx Zynq FPGA Manager registered xt_time: kernel timezone is -0000 ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully NET: Registered protocol family 17 Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates mmc0: new high speed SDXC card at address 0001 input: gpio_keys as /devices/soc0/gpio_keys/input/input0 mmcblk0: mmc0:0001 SD16G 58.2 GiB clk: Not disabling unused clocks ALSA device list: No soundcards found. mmcblk0: p1 p2 p3 random: fast init done EXT4-fs (mmcblk0p2): 1 orphan inode deleted EXT4-fs (mmcblk0p2): recovery complete EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K Run /sbin/init as init process systemd[1]: System time before build time, advancing clock. systemd[1]: Failed to look up module alias 'autofs4': Function not implemented systemd[1]: systemd 247.3-7+rpi1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) systemd[1]: Detected architecture arm. Welcome to Kuiper GNU/Linux 11.2 (bullseye)! systemd[1]: Set hostname to . systemd[1]: Binding to IPv6 address not available since kernel does not support IPv6. systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed. systemd[1]: Queued start job for default target Graphical Interface. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. systemd[1]: (This warning is only shown for the first unit using IP firewalling.) systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. random: systemd: uninitialized urandom read (16 bytes read) systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Created slice system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. systemd[1]: Condition check resulted in Journal Audit Socket being skipped. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Condition check resulted in Huge Pages File System being skipped. systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. systemd[1]: Mounting RPC Pipe File System... Mounting RPC Pipe File System... systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... systemd[1]: Condition check resulted in Kernel Trace File System being skipped. systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped. systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... systemd[1]: Starting Set the console keyboard layout... Starting Set the console keyboard layout... systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. systemd[1]: Condition check resulted in File System Check on Root Device being skipped. systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... systemd[1]: run-rpc_pipefs.mount: Mount process exited, code=exited, status=32/n/a systemd[1]: run-rpc_pipefs.mount: Failed with result 'exit-code'. systemd[1]: Failed to mount RPC Pipe File System. [FAILED] Failed to mount RPC Pipe File System. See 'systemctl status run-rpc_pipefs.mount' for details. systemd[1]: Dependency failed for RPC security service for NFS client and server. [DEPEND] Dependency failed for RPC …ice for NFS client and server. systemd[1]: rpc-gssd.service: Job rpc-gssd.service/start failed with result 'dependency'. systemd[1]: Dependency failed for RPC security service for NFS server. [DEPEND] Dependency failed for RPC …curity service for NFS server. systemd[1]: rpc-svcgssd.service: Job rpc-svcgssd.service/start failed with result 'dependency'. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. random: crng init done random: 7 urandom warning(s) missed due to ratelimiting [ OK ] Mounted Kernel Debug File System. [ OK ] Finished Restore / save the current clock. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Reached target NFS client services. [ OK ] Reached target Remote File Systems (Pre). EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ OK ] Reached target Remote File Systems. Mounting Kernel Configuration File System... Starting Apply Kernel Variables... [ OK ] Finished Set the console keyboard layout. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. Starting Helper to synchronize boot up for ifupdown... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Create System Users... Starting Wait for udev To …plete Device Initialization... [ OK ] Finished Create System Users. [ OK ] Finished Load/Save Random Seed. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Show Plymouth Boot Screen... [ OK ] Started Show Plymouth Boot Screen. [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Found device /dev/ttyPS0. [ OK ] Found device /dev/disk/by-partuuid/f7eeebee-01. [ OK ] Finished Helper to synchronize boot up for ifupdown. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting File System Check…isk/by-partuuid/f7eeebee-01... [ OK ] Started File System Check Daemon to report status. [ OK ] Finished File System Check…/disk/by-partuuid/f7eeebee-01. Mounting /boot... [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. Starting Set console font and keymap... Starting Raise network interfaces... Starting Preprocess NFS configuration... Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... [ OK ] Finished Set console font and keymap. [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ OK ] Finished Preprocess NFS configuration. [ OK ] Finished Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started CUPS Scheduler. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Paths. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on CUPS Scheduler. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on GPS (Global P…ioning System) Daemon Sockets. [ OK ] Listening on triggerhappy.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting dphys-swapfile - …unt, and delete a swap file... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting Creating IIOD Context Attributes...... Starting DHCP Client Daemon... Starting LSB: Switch to on…nless shift key is pressed)... Starting LSB: rng-tools (Debian variant)... Starting System Logging Service... Starting User Login Management... Starting triggerhappy global hotkey daemon... Starting Disk Manager... Starting WPA supplicant... [ OK ] Started triggerhappy global hotkey daemon. [ OK ] Started System Logging Service. [ OK ] Started DHCP Client Daemon. [ OK ] Finished dphys-swapfile - …mount, and delete a swap file. [ OK ] Started LSB: rng-tools (Debian variant). [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started WPA supplicant. [ OK ] Started User Login Management. Starting Authorization Manager... [ OK ] Started Authorization Manager. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Finished Raise network interfaces. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. Starting CUPS Scheduler... Starting HTTP based time synchronization tool... Starting Internet superserver... Starting LSB: DHCP server... Starting /etc/rc.local Compatibility... Starting OpenBSD Secure Shell server... Starting Permit User Sessions... My IP address is 192.168.10.122 [ OK ] Started Unattended Upgrades Shutdown. Starting LSB: Webfs simple HTTP server... [ OK ] Started Internet superserver. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Finished Permit User Sessions. [ OK ] Started HTTP based time synchronization tool. [ OK ] Started LSB: Switch to ond…(unless shift key is pressed). Starting Light Display Manager... Starting Hold until boot process finishes up... [ OK ] Started CUPS Scheduler. [ OK ] Started Make remote CUPS printers available locally. [ OK ] Started Disk Manager. [ OK ] Started LSB: Webfs simple HTTP server. [ OK ] Finished Creating IIOD Context Attributes.... [ OK ] Started IIO Daemon. [FAILED] Failed to start VNC Server for X11. [FAILED] Failed to start LSB: DHCP server. Raspbian GNU/Linux 11 analog ttyPS0 analog login: root (automatic login) Linux analog 5.10.0-98248-g1bbe32fa5182-dirty #6 SMP PREEMPT Tue Mar 14 12:13:23 CET 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Thu Feb 9 10:45:27 GMT 2023 on ttyPS0 root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# root@analog:~# U-Boot 2018.01-21439-gd244ce5 (Jul 29 2021 - 16:33:01 +0100), Build: jenkins-development-build_uboot-1 Model: Zynq Zed Development Board Board: Xilinx Zynq Silicon: v3.1 DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 (SD) SF: Detected n25q256a with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 reading uEnv.txt 407 bytes read in 20 ms (19.5 KiB/s) Importing environment from SD ... Hit any key to stop autoboot: 0 Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> Zynq> U-Boot 2014.07-dirty (Nov 20 2014 - 17:05:21) Board: Xilinx Zynq I2C: ready DRAM: ECC disabled 512 MiB MMC: zynq_sdhci: 0 SF: Detected N25Q256A with page size 256 Bytes, erase size 4 KiB, total 32 MiB In: serial Out: serial Err: serial Net: Gem.e000b000 Hit any key to stop autoboot: 0 Device: zynq_sdhci Manufacturer ID: fe OEM: 3432 Name: 00000 Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 58.2 GiB Bus Width: 4-bit Unknown command 'load' - try 'help' Copying Linux from SD to RAM... reading uImage 4553056 bytes read in 401 ms (10.8 MiB/s) reading devicetree.dtb 20747 bytes read in 17 ms (1.2 MiB/s) libfdt fdt_setprop(): FDT_ERR_NOSPACE Loaded AD9361 refclk frequency and model into devicetree reading uramdisk.image.gz ** Unable to read file uramdisk.image.gz ** ## Booting kernel from Legacy Image at 02080000 ... Image Name: Linux-4.14.0-gb6e3799-dirty Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4552992 Bytes = 4.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02000000 Booting using the fdt blob at 0x2000000 Loading Kernel Image ... OK Loading Device Tree to 1ed1b000, end 1ed2310a ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 4.14.0-gb6e3799-dirty (microphase@microphase-dev) (gcc version 7.3.1 20180314 (Linaro GCC 7.3-2018.04-rc3)) #1 SMP PREEMPT Thu Aug 12 12:24:19 CST 2021 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: ADRV9361-Z7035 bootconsole [earlycon0] enabled Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x38000000 random: fast init done percpu: Embedded 16 pages/cpu @ef7c8000 s33036 r8192 d24308 u65536 Built 1 zonelists, mobility grouping on. Total pages: 260608 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext4 rootwait PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 895988K/1048576K available (7168K kernel code, 340K rwdata, 2376K rodata, 1024K init, 160K bss, 21516K reserved, 131072K cma-reserved, 131072K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0800000 (8160 kB) .init : 0xc0b00000 - 0xc0c00000 (1024 kB) .data : 0xc0c00000 - 0xc0c551e0 ( 341 kB) .bss : 0xc0c5ab38 - 0xc0c82e84 ( 161 kB) Preemptible hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Tasks RCU enabled. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to f0802000 slcr mapped to f0804000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at f0804100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at f080c000, irq=17 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0880000 zynq-pinctrl 700.pinctrl: zynq pinctrl initialized e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 25, base_baud = 6249999) is a xuartps `��k����[ttyPS0] enabled console [ttyPS0] enabled bootconsole [earlycon0] disabled bootconsole [earlycon0] disabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb media: Linux media interface: v0.10 Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available workingset: timestamp_bits=30 max_order=18 bucket_order=0 bounce: pool size: 64 pages io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) io scheduler mq-deadline registered io scheduler kyber registered dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded m25p80 spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 m25p80 spi1.0: n25q256a (32768 Kbytes) 6 ofpart partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 28 (00:05:f7:80:1b:ab) Marvell 88E1510 e000b000.ethernet-ffffffff:00: attached PHY driver [Marvell 88E1510] (mii_bus:phy_addr=e000b000.ethernet-ffffffff:00, irq=POLL) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device chipidea-usb2 e0002000.usb: e0002000.usb supply vbus not found, using dummy regulator ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer at f0963000 with timeout 10s Xilinx Zynq CpuIdle Driver started sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA ledtrig-cpu: registered to indicate activity on CPUs hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver ad7291: probe of 0-002f failed with error -5 fpga_manager fpga0: Xilinx Zynq FPGA Manager registered Netfilter messages via NETLINK v0.30. nfnl_acct: registering with nfnetlink. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) mmc0: new high speed SDXC card at address 0001 mmcblk0: mmc0:0001 00000 58.2 GiB mmcblk0: p1 p2 p3 ctnetlink v0.93: registering with nfnetlink. nf_tables: (c) 2007-2009 Patrick McHardy nf_tables_compat: (c) 2012 Pablo Neira Ayuso xt_time: kernel timezone is -0000 ip_tables: (C) 2000-2006 Netfilter Core Team ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: arp_tables: (C) 2002 David S. Miller NET: Registered protocol family 17 Registering SWP/SWPB emulation handler input: gpio_keys as /devices/soc0/gpio_keys/input/input0 hctosys: unable to open rtc device (rtc0) ALSA device list: No soundcards found. EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory init: hwclock main process (929) terminated with status 1 * Setting up X socket directories... [ OK ] * STARTDISTCC is set to false in /etc/default/distcc * /usr/bin/distccd not starting * Starting httpd daemon webfsd [ OK ] * Starting IIO Daemon iiod [ OK ] Last login: Thu Jan 1 00:00:09 UTC 1970 on tty1 Welcome to Linaro 14.04 (GNU/Linux 4.14.0-gb6e3799-dirty armv7l) * Documentation: https://wiki.analog.com/ https://ez.analog.com/ root@analog:~# root@analog:~# dmesg Booting Linux on physical CPU 0x0 Linux version 4.14.0-gb6e3799-dirty (microphase@microphase-dev) (gcc version 7.3.1 20180314 (Linaro GCC 7.3-2018.04-rc3)) #1 SMP PREEMPT Thu Aug 12 12:24:19 CST 2021 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: ADRV9361-Z7035 bootconsole [earlycon0] enabled Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x38000000 On node 0 totalpages: 262144 free_area_init_node: node 0, pgdat c0c54340, node_mem_map ef7f7000 Normal zone: 1536 pages used for memmap Normal zone: 0 pages reserved Normal zone: 196608 pages, LIFO batch:31 HighMem zone: 65536 pages, LIFO batch:15 random: fast init done percpu: Embedded 16 pages/cpu @ef7c8000 s33036 r8192 d24308 u65536 pcpu-alloc: s33036 r8192 d24308 u65536 alloc=16*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists, mobility grouping on. Total pages: 260608 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext4 rootwait PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 895988K/1048576K available (7168K kernel code, 340K rwdata, 2376K rodata, 1024K init, 160K bss, 21516K reserved, 131072K cma-reserved, 131072K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0800000 (8160 kB) .init : 0xc0b00000 - 0xc0c00000 (1024 kB) .data : 0xc0c00000 - 0xc0c551e0 ( 341 kB) .bss : 0xc0c5ab38 - 0xc0c82e84 ( 161 kB) Preemptible hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Tasks RCU enabled. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to f0802000 slcr mapped to f0804000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at f0804100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at f080c000, irq=17 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0880000 zynq-pinctrl 700.pinctrl: zynq pinctrl initialized e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 25, base_baud = 6249999) is a xuartps console [ttyPS0] enabled bootconsole [earlycon0] disabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb media: Linux media interface: v0.10 Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available workingset: timestamp_bits=30 max_order=18 bucket_order=0 bounce: pool size: 64 pages io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) io scheduler mq-deadline registered io scheduler kyber registered dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded m25p80 spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 m25p80 spi1.0: n25q256a (32768 Kbytes) 6 ofpart partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 28 (00:05:f7:80:1b:ab) Marvell 88E1510 e000b000.ethernet-ffffffff:00: attached PHY driver [Marvell 88E1510] (mii_bus:phy_addr=e000b000.ethernet-ffffffff:00, irq=POLL) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device chipidea-usb2 e0002000.usb: e0002000.usb supply vbus not found, using dummy regulator ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer at f0963000 with timeout 10s Xilinx Zynq CpuIdle Driver started sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA ledtrig-cpu: registered to indicate activity on CPUs hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver ad7291: probe of 0-002f failed with error -5 fpga_manager fpga0: Xilinx Zynq FPGA Manager registered Netfilter messages via NETLINK v0.30. nfnl_acct: registering with nfnetlink. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) mmc0: new high speed SDXC card at address 0001 mmcblk0: mmc0:0001 00000 58.2 GiB mmcblk0: p1 p2 p3 ctnetlink v0.93: registering with nfnetlink. nf_tables: (c) 2007-2009 Patrick McHardy nf_tables_compat: (c) 2012 Pablo Neira Ayuso xt_time: kernel timezone is -0000 ip_tables: (C) 2000-2006 Netfilter Core Team ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: arp_tables: (C) 2002 David S. Miller NET: Registered protocol family 17 Registering SWP/SWPB emulation handler input: gpio_keys as /devices/soc0/gpio_keys/input/input0 hctosys: unable to open rtc device (rtc0) ALSA device list: No soundcards found. EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K init: hwclock main process (929) terminated with status 1 systemd-udevd[1019]: starting version 204 ad9361 spi0.0: ad9361_probe : enter (ad9361) Registered mathworks_ip class mwipcore 43c00000.mwipcore: Dev memory resource found at 43c00000 0000FFFF. mwipcore 43c00000.mwipcore: 'mwipcore' device not found, creating mwipcore 43c00000.mwipcore: Char dev region registered: major num:242 mwipcore 43c00000.mwipcore: 'mwipcore' device created xilinx-vdma 80400000.dma: Xilinx AXI DMA Engine Driver Probed!! xilinx-vdma 80410000.dma: Xilinx AXI DMA Engine Driver Probed!! ad9361 spi0.0: ad9361_probe : AD936x Rev 2 successfully initialized init: udev-fallback-graphics main process (1473) terminated with status 1 NET: Registered protocol family 10 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Segment Routing with IPv6 cf_axi_adc 79020000.cf-ad9361-lpc: ADI AIM (10.01.b) at 0x79020000 mapped to 0xf0e58000, probed ADC AD9361 as MASTER cf_axi_dds 79024000.cf-ad9361-dds-core-lpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.01.b) at 0x79024000 mapped to 0xf195f000, probed DDS AD9361 init: failsafe main process (1529) killed by TERM signal init: samba-ad-dc main process (1686) terminated with status 1 init: alsa-restore main process (1777) terminated with status 19 init: isc-dhcp-server main process (1783) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: lightdm main process (1731) terminated with status 1 init: isc-dhcp-server main process (1870) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (1894) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (1924) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: tty1 main process (1942) killed by TERM signal init: isc-dhcp-server main process (1967) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (1996) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2021) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2029) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2037) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2045) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2053) terminated with status 1 init: isc-dhcp-server respawning too fast, stopped root@analog:~# df Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 6461384 3248364 2861740 54% / devtmpfs 447992 4 447988 1% /dev none 4 0 4 0% /sys/fs/cgroup none 102812 380 102432 1% /run none 5120 0 5120 0% /run/lock none 514040 0 514040 0% /run/shm none 102400 0 102400 0% /run/user root@analog:~# df Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 6461384 3248368 2861736 54% / devtmpfs 447992 4 447988 1% /dev none 4 0 4 0% /sys/fs/cgroup none 102812 380 102432 1% /run none 5120 0 5120 0% /run/lock none 514040 0 514040 0% /run/shm none 102400 0 102400 0% /run/user root@analog:~# cls -bash: cls: command not found root@analog:~# clear root@analog:~# dmesg Booting Linux on physical CPU 0x0 Linux version 4.14.0-gb6e3799-dirty (microphase@microphase-dev) (gcc version 7.3.1 20180314 (Linaro GCC 7.3-2018.04-rc3)) #1 SMP PREEMPT Thu Aug 12 12:24:19 CST 2021 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: ADRV9361-Z7035 bootconsole [earlycon0] enabled Memory policy: Data cache writealloc cma: Reserved 128 MiB at 0x38000000 On node 0 totalpages: 262144 free_area_init_node: node 0, pgdat c0c54340, node_mem_map ef7f7000 Normal zone: 1536 pages used for memmap Normal zone: 0 pages reserved Normal zone: 196608 pages, LIFO batch:31 HighMem zone: 65536 pages, LIFO batch:15 random: fast init done percpu: Embedded 16 pages/cpu @ef7c8000 s33036 r8192 d24308 u65536 pcpu-alloc: s33036 r8192 d24308 u65536 alloc=16*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists, mobility grouping on. Total pages: 260608 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext4 rootwait PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 895988K/1048576K available (7168K kernel code, 340K rwdata, 2376K rodata, 1024K init, 160K bss, 21516K reserved, 131072K cma-reserved, 131072K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0800000 (8160 kB) .init : 0xc0b00000 - 0xc0c00000 (1024 kB) .data : 0xc0c00000 - 0xc0c551e0 ( 341 kB) .bss : 0xc0c5ab38 - 0xc0c82e84 ( 161 kB) Preemptible hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Tasks RCU enabled. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to f0802000 slcr mapped to f0804000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at f0804100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at f080c000, irq=17 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0880000 zynq-pinctrl 700.pinctrl: zynq pinctrl initialized e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 25, base_baud = 6249999) is a xuartps console [ttyPS0] enabled bootconsole [earlycon0] disabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb media: Linux media interface: v0.10 Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered FPGA manager framework Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available workingset: timestamp_bits=30 max_order=18 bucket_order=0 bounce: pool size: 64 pages io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) io scheduler mq-deadline registered io scheduler kyber registered dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded m25p80 spi1.0: SPI-NOR-UniqueID 1044734c9605001818003200c3d54ff486 m25p80 spi1.0: n25q256a (32768 Kbytes) 6 ofpart partitions found on MTD device spi1.0 Creating 6 MTD partitions on "spi1.0": 0x000000000000-0x0000000e0000 : "qspi-fsbl-uboot" 0x0000000e0000-0x000000100000 : "qspi-uboot-env" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000001300000 : "qspi-rootfs" 0x000001300000-0x000002000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed tun: Universal TUN/TAP device driver, 1.6 libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 28 (00:05:f7:80:1b:ab) Marvell 88E1510 e000b000.ethernet-ffffffff:00: attached PHY driver [Marvell 88E1510] (mii_bus:phy_addr=e000b000.ethernet-ffffffff:00, irq=POLL) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device chipidea-usb2 e0002000.usb: e0002000.usb supply vbus not found, using dummy regulator ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected i2c /dev entries driver at24 0-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write IR NEC protocol handler initialized IR RC5(x/sz) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR SANYO protocol handler initialized IR Sharp protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR XMP protocol handler initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer at f0963000 with timeout 10s Xilinx Zynq CpuIdle Driver started sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA ledtrig-cpu: registered to indicate activity on CPUs hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver ad7291: probe of 0-002f failed with error -5 fpga_manager fpga0: Xilinx Zynq FPGA Manager registered Netfilter messages via NETLINK v0.30. nfnl_acct: registering with nfnetlink. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) mmc0: new high speed SDXC card at address 0001 mmcblk0: mmc0:0001 00000 58.2 GiB mmcblk0: p1 p2 p3 ctnetlink v0.93: registering with nfnetlink. nf_tables: (c) 2007-2009 Patrick McHardy nf_tables_compat: (c) 2012 Pablo Neira Ayuso xt_time: kernel timezone is -0000 ip_tables: (C) 2000-2006 Netfilter Core Team ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: arp_tables: (C) 2002 David S. Miller NET: Registered protocol family 17 Registering SWP/SWPB emulation handler input: gpio_keys as /devices/soc0/gpio_keys/input/input0 hctosys: unable to open rtc device (rtc0) ALSA device list: No soundcards found. EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 1024K init: hwclock main process (929) terminated with status 1 systemd-udevd[1019]: starting version 204 ad9361 spi0.0: ad9361_probe : enter (ad9361) Registered mathworks_ip class mwipcore 43c00000.mwipcore: Dev memory resource found at 43c00000 0000FFFF. mwipcore 43c00000.mwipcore: 'mwipcore' device not found, creating mwipcore 43c00000.mwipcore: Char dev region registered: major num:242 mwipcore 43c00000.mwipcore: 'mwipcore' device created xilinx-vdma 80400000.dma: Xilinx AXI DMA Engine Driver Probed!! xilinx-vdma 80410000.dma: Xilinx AXI DMA Engine Driver Probed!! ad9361 spi0.0: ad9361_probe : AD936x Rev 2 successfully initialized init: udev-fallback-graphics main process (1473) terminated with status 1 NET: Registered protocol family 10 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Segment Routing with IPv6 cf_axi_adc 79020000.cf-ad9361-lpc: ADI AIM (10.01.b) at 0x79020000 mapped to 0xf0e58000, probed ADC AD9361 as MASTER cf_axi_dds 79024000.cf-ad9361-dds-core-lpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.01.b) at 0x79024000 mapped to 0xf195f000, probed DDS AD9361 init: failsafe main process (1529) killed by TERM signal init: samba-ad-dc main process (1686) terminated with status 1 init: alsa-restore main process (1777) terminated with status 19 init: isc-dhcp-server main process (1783) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: lightdm main process (1731) terminated with status 1 init: isc-dhcp-server main process (1870) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (1894) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (1924) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: tty1 main process (1942) killed by TERM signal init: isc-dhcp-server main process (1967) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (1996) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2021) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2029) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2037) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2045) terminated with status 1 init: isc-dhcp-server main process ended, respawning init: isc-dhcp-server main process (2053) terminated with status 1 init: isc-dhcp-server respawning too fast, stopped random: crng init done root@analog:~# root@analog:~# root@analog:~#