forked from Formlabs/OpenFL
-
Notifications
You must be signed in to change notification settings - Fork 1
/
Form_1+_FLGPCL02_100.ini
85 lines (76 loc) · 6.7 KB
/
Form_1+_FLGPCL02_100.ini
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
;;;;;;;;;;;;;;;;; FORMLABS MATERIAL CONFIGURATION ;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;; ,;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;: ;;;;;;;;;;;;
;;;;;;;;, : ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;` `;;;;;;;;
;;;;;;; ;;;;;;;, ;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;
;;;;;;; `;;;; ,;;;;;;;;;;;;;;;: ;;;;;;;
;;;;;;;;. ;;;;` , ;;;;;;;;;` ;;;; ;;;;;;;;
;;;;;;;;;; ;;;;;;;;; ;;; :;;;;;;;;: :;;;;;;;;;
;;;;;;;;;;;; ;;;;;;;;;;;;;;;. ,;;;;;;;;;;;;;;;; ,;;;;;;;;;;;
;;;;;;;;;;;;; ;;;;;;;;;;;, , ,;;;;;;;;;;;` ;;;;;;;;;;;;;
;;;;;;;;;;;;;;, :;;;;;;: ;` ,;;;;;;; ;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;; ;;: ; ` ;;; :;;; .;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;; ;; ; :;;;; ;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;; :;; ; ;;;;;. :;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; ;;; ;;: ;;;;;;; ;;;;;;;;;;;;;;
;;;;;;;;;;;;;;, ;;;: ,;;; :;;;;;;;; `;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;; `;;;;; ;;;;;;;;;, ;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;` ;;, ;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;; WARNING: Modifying these settings can lead to damage ;;;;;;
;;;;;;;;;; to your Form 1+ and void its warranty. ;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
[Overview]
MaterialName = Clear
;--------------------------- POWER / SPEED SETTINGS ---------------------------
[perimeter]
basexyfeedrate = 800 ; Laser speed in mm/s for the perimeter of the base (aka raft). (Faster than 800 mm/s may noticably reduce surface quality.)
baselaserpowermw = 49 ; Laser power in mW used for the perimeter of the base (aka raft). (max: 62 mW for Form 1+)
modelxyfeedrate = 800 ; Laser speed in mm/s for the perimeter of the model. (Faster than 800 mm/s may noticably reduce surface quality.)
modellaserpowermw = 48 ; Laser power in mW for the perimeter of the model (max: 62 mW for Form 1+)
supportxyfeedrate = 800 ; Laser speed in mm/s for the perimeter of the supports. (Faster than 800 mm/s may noticably reduce surface quality.)
supportlaserpowermw = 53 ; Laser power in mW for the perimeter of thesupports. (max: 62 mW for Form 1+)
[fill]
basexyfeedrate = 1500 ; Laser speed in mm/s used for filling the base (aka raft). (Faster than about 1600 mm/s may produce noticable artifacts.)
baselaserpowermw = 62 ; Laser power in mW used for filling the base (aka raft). (max: 62 mW for Form 1+)
modelxyfeedrate = 1550 ; Laser speed in mm/s used for filling the model. (Faster than about 1600 mm/s may produce noticable artifacts.)
modellaserpowermw = 62 ; Laser power in mW for the model. (max: 62 mW for Form 1+)
supportxyfeedrate = 1500 ; Laser speed in mm/s used for filling supports. (Faster than about 1600 mm/s may produce noticable artifacts.)
supportlaserpowermw = 62 ; Laser power in mW for filling supports.
;--------------------------- LAYER PASS SETTINGS ------------------------------
[laserRoutine]
firstlayerpasses = 10 ; The number of laser passes to do for layer 0 to attach to the build platform.
otherlayerpasses = 1 ; The number of laser passes to do for most layers (typically 1).
earlylayerpasses = 2 ; The number of laser passes to do for early layers as defined by earlytimesexpose.
;--------------------------- LAYER SETTINGS -----------------------------------
[PrintSettings]
SliceHeight = 0.1 ; The layer thickness in mm. For example 0.1 is 100 microns. Be aware that values not corresponding to whole z-motor microsteps (0.0025 mm) will be rounded.
ScanlineSpacing = 0.09 ; Spacing of fill lines in mm.
InnerBoundaryOffset = 0.12 ; Offset from model outmost outline to perimeter in mm. Conceptually this is the curing radius of the inermost outline.
OuterBoundaryOffset = 0.03 ; Offset from model perimeter to outermost outline in mm. Conceptually this is the curing radius of the outermost outline.
Xcorrectionfactor = 1.008 ; Scale factor for the x axis to account for shrinkage.
Ycorrectionfactor = 1.008 ; Scale factor for the y axis to account for shrinkage.
ScanlineBoundaryOffset = 0.03 ; Offset in mm from the innermost outline to the boundary of the fill. If this is zero, the fill touches the innermost outline; if this is positive it does not; if this is negative, the fill overlaps at least the inner outline.
OffsetsNum = 3 ; Number of outlines to draw. min: 0; max: unlimited
;--------------------------- TILT PEEL SETTINGS -----------------------------------
[btwnLayerRoutine]
earlytimesexpose = 50 ; The number of layers that will be exposed earlylayerpasses times (excluding layer 0). That is, if earlytimesexpose is 3 and earlylayerpasses is 2, layer 0 will get firstlayerpasses passes, layer 1 and 2 will get 2 passes, and subsequent layers will get otherlayerpasses passes.
postlasercurewait = 1 ; Duration in seconds to wait from when the laser turns off until the motors start to move.
earlytimespeel = 22 ; The number of layers for which the p1 moves will be done. These are typically slower moves.
p1downvel = 1 ; Initial tilt speed in mm/s (at the tilt motor).
p1downmove = 10 ; Initial tilt distance in mm.
p1upvel = 4 ; Velocity of p1upmove in mm/s.
p1upmove = -10 ; Tilt up-move displacement in mm (should be negative).
p1upslowvel = 10 ; Velocity for p1upslowmove in mm/s.
p1upslowmove = -0.5 ; Additional up move in mm to overdrive into the hard stop. (Should be negative or zero.)
p2downvel = 1.5 ; Velocity of p2downmove in mm/s.
p2downmove = 7.5 ; After earlytimespeel, tilt distance in mm.
p2upvel = 10 ; Speed of p2upmove in mm/s.
p2upmove = -7.5 ; After earlytimespeel, un-tilt distance in mm. (should be negative.)
p2upslowvel = 10 ; Speed of p2upslowmove in mm/s.
p2upslowmove = -0.1 ; After earlytimespeel, overdrive distance into hard stop in mm. (Should be negative or zero.)
squishwaitmin_s = 0.25 ; Low end of the time in seconds we wait between finishing squishing and turning on the laser.
squishwaitmax_s = 2 ; High end of the time in seconds we wait between finishing squishing and turning on the laser.