Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

FS#1586 - DAP-1522 A1 factory to snapshot kernel panic and system halt #6527

Open
openwrt-bot opened this issue Jun 11, 2018 · 0 comments
Open

FS#1586 - DAP-1522 A1 factory to snapshot kernel panic and system halt #6527

openwrt-bot opened this issue Jun 11, 2018 · 0 comments
Labels

Comments

@openwrt-bot
Copy link

@openwrt-bot openwrt-bot commented Jun 11, 2018

danmero:

DAP-1522 A1 stock firmware 1.21 or 1.42 , device page https://openwrt.org/toh/hwdata/d-link/d-link_dap-1522_a1
Flash via GUI or Recovery interface , both the same result/fail.
Since this device is not supported on 17.04.1 https://downloads.lede-project.org/releases/17.01.4/targets/ramips/rt288x/
I try the snapshot from https://downloads.openwrt.org/snapshots/targets/ramips/rt288x/openwrt-ramips-rt288x-dlink_dap-1522-a1-squashfs-factory.bin
Checksum ok

Here is the boot log

U-Boot 1.1.3 (Aug 28 2009 - 15:47:01) Build 001--ALPHA_v011

Board: RT2880 DRAM: 32 MB
twe0 set to
toe0 set to

ASIC -VerB/C (MAC to MAC Mode)
DRAM COMPONENT=256Mbits
DRAM BUS=16BIT
Total memory = 32Mbytes
Date:Aug 28 2009 Time:15:47:01

Eth0 (10/100-M)

Hit any key to stop autoboot: 0

Booting image at bc440000 ...

Image Name: 7zip Linux Kernel
Created: 1970-01-01 0:00:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: -1 Bytes = 4096 MB
Load Address: 8a000000
Entry Point: 8a000000
Uncompressing Kernel Image with LZMA ...
OK

Starting kernel ...

[ 0.000000] Linux version 4.14.48 (buildbot@slashdirt-02) (gcc version 7.3.0 (OpenWrt GCC 7.3.0
r7172-f60301d)) #0 Sat Jun 9 20:39:17 2018
[ 0.000000] SoC Type: Ralink RT2880 id:2 rev:0
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001906c (MIPS 4KEc)
[ 0.000000] MIPS: machine is D-Link DAP-1522 A1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 08000000 (usable)
[ 0.000000] Wasting 1048576 bytes for tracking 32768 unused pages
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000009ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000009ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000009ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x47c with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 40640
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 25248K/163840K available (3518K kernel code, 174K rwdata, 844K rodata, 1216K
init, 214K bss, 138592K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] Failed to request intc memory
[ 0.000000] Kernel panic - not syncing: Failed to request resources for ralin k,rt2880-sysc
[ 0.000000] Rebooting in 1 seconds..
[ 0.000000] Reboot failed -- System halted

Regards,

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Labels
Projects
None yet
Development

No branches or pull requests

1 participant