You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
USB3 port does not work
USB3 port with usb2 mode does not work
USB2 port works
serial console bootlog attached with lsusb -v output
error when plugging in:
MT76x2u USB3 WLAN Stick (AVM AC860)
similar error with USB2 Sandisk Cruzer in USB3 port
USB2 works fine
[ 242.139499] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[ 242.296773] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 242.315697] scsi host0: usb-storage 2-1:1.0
[ 242.732028] usb 2-1: USB disconnect, device number 2
[ 243.572844] usb 2-1: new high-speed USB device number 3 using xhci_hcd
[ 243.863787] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[ 249.227352] usb 2-1: device descriptor read/64, error -145
[ 264.842949] usb 2-1: device descriptor read/64, error -145
[ 265.082936] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[ 270.218798] usb 2-1: device descriptor read/64, error -145
[ 285.832404] usb 2-1: device descriptor read/64, error -145
[ 286.072347] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[ 286.099195] mt76x2u 2-1:1.0: ASIC revision: 76120044
[ 286.201135] mt76x2u 2-1:1.0: ROM patch build: 20141115060606a
[ 286.319536] xhci_hcd 0000:00:00.0: ERROR unknown event type 37
[ 286.419382] xhci_hcd 0000:00:00.0: ERROR unknown event type 37
... (multiple entries)
[ 292.359183] xhci_hcd 0000:00:00.0: xHCI host not responding to stop endpoint command.
[ 292.383111] xhci_hcd 0000:00:00.0: xHCI host controller not responding, assume dead
[ 292.391018] xhci_hcd 0000:00:00.0: HC died; cleaning up
[ 292.396412] mt76x2u 2-1:1.0: firmware upload failed: -145
[ 304.743396] mt76x2u 2-1:1.0: MAC RX failed to stop
[ 304.962109] mt76x2u: probe of 2-1:1.0 failed with error -5
[ 304.971982] usb 2-1: USB disconnect, device number 3
lspci -v -nnn
lspci -v -nnnn
00:00.0 USB controller [0c03]: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023] (rev 01) (prog-if 30 [XHCI])
Subsystem: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023]
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at 10000000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [50] Power Management version 3
Capabilities: [70] MSI: Enable- Count=1/4 Maskable+ 64bit+
Capabilities: [a0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [190] Device Serial Number 01-01-01-01-01-01-01-01
Kernel driver in use: xhci_hcd
lspci: Unable to load libkmod resources: error -12
01:00.0 Network controller [0280]: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter [168c:003c]
Device tree node: /sys/firmware/devicetree/base/ahb/pcie-controller@18250000/wifi@0,0
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at 12000000 (64-bit, non-prefetchable) [size=2M]
Expansion ROM at 12200000 [virtual] [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
Kernel driver in use: ath10k_pci
The text was updated successfully, but these errors were encountered:
plntyk:
Sitecom WLR-8100v1 (Sitecom WLR-8100v1 001 X8 AC1750) with integrated Etron EJ168A USB3 Controller [1b6f:7023]
USB3 port does not work
USB3 port with usb2 mode does not work
USB2 port works
serial console bootlog attached with lsusb -v output
error when plugging in:
[ 242.139499] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[ 242.296773] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 242.315697] scsi host0: usb-storage 2-1:1.0
[ 242.732028] usb 2-1: USB disconnect, device number 2
[ 243.572844] usb 2-1: new high-speed USB device number 3 using xhci_hcd
[ 243.863787] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[ 249.227352] usb 2-1: device descriptor read/64, error -145
[ 264.842949] usb 2-1: device descriptor read/64, error -145
[ 265.082936] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[ 270.218798] usb 2-1: device descriptor read/64, error -145
[ 285.832404] usb 2-1: device descriptor read/64, error -145
[ 286.072347] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[ 286.099195] mt76x2u 2-1:1.0: ASIC revision: 76120044
[ 286.201135] mt76x2u 2-1:1.0: ROM patch build: 20141115060606a
[ 286.319536] xhci_hcd 0000:00:00.0: ERROR unknown event type 37
[ 286.419382] xhci_hcd 0000:00:00.0: ERROR unknown event type 37
... (multiple entries)
[ 292.359183] xhci_hcd 0000:00:00.0: xHCI host not responding to stop endpoint command.
[ 292.383111] xhci_hcd 0000:00:00.0: xHCI host controller not responding, assume dead
[ 292.391018] xhci_hcd 0000:00:00.0: HC died; cleaning up
[ 292.396412] mt76x2u 2-1:1.0: firmware upload failed: -145
[ 304.743396] mt76x2u 2-1:1.0: MAC RX failed to stop
[ 304.962109] mt76x2u: probe of 2-1:1.0 failed with error -5
[ 304.971982] usb 2-1: USB disconnect, device number 3
lspci -v -nnn
lspci -v -nnnn
00:00.0 USB controller [0c03]: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023] (rev 01) (prog-if 30 [XHCI])
Subsystem: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023]
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at 10000000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [50] Power Management version 3
Capabilities: [70] MSI: Enable- Count=1/4 Maskable+ 64bit+
Capabilities: [a0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [190] Device Serial Number 01-01-01-01-01-01-01-01
Kernel driver in use: xhci_hcd
lspci: Unable to load libkmod resources: error -12
01:00.0 Network controller [0280]: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter [168c:003c]
Device tree node: /sys/firmware/devicetree/base/ahb/pcie-controller@18250000/wifi@0,0
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at 12000000 (64-bit, non-prefetchable) [size=2M]
Expansion ROM at 12200000 [virtual] [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
Kernel driver in use: ath10k_pci
The text was updated successfully, but these errors were encountered: