Skip to content

Latest commit

 

History

History
530 lines (391 loc) · 35.5 KB

README.md

File metadata and controls

530 lines (391 loc) · 35.5 KB

Pravega Sensor Collector

Pravega Sensor Collector collects data from sensors and ingests the data into Pravega streams.

Overview

Pravega Sensor Collector can continuously collect high-resolution samples without interruption, even if the network connection to the Pravega server is unavailable for long periods. For instance, in a connected train use case, there may be long periods of time between cities where there is no network access. During this time, Pravega Sensor Collector will store collected sensor data on a local disk and periodically attempt to reconnect to the Pravega server. It stores this sensor data in local SQLite database files. When transferring samples from a SQLite database file to Pravega, it coordinates a SQLite transaction and a Pravega transaction. This technique allows it to guarantee that all samples are sent in order, without gaps, and without duplicates, even in the presence of computer, network, and power failures.

Pravega Sensor Collector is designed to collect samples at a rate of up to 1000 samples per second (1 kHz). This makes it possible, for instance, to measure high frequency vibrations from accelerometers. It batches multiple samples into larger events that are periodically sent to Pravega. The batch size is configurable to allow you to tune the trade-off between latency and throughput that is appropriate for your use case.

Pravega Sensor Collector is a Java application. It has a plug-in architecture to allow Java developers to easily add drivers for different types of sensors or to transform the sensor data in different ways.

About Pravega

Pravega is an open-source storage system for streams built from the ground up to ingest data from continuous data sources and meet the stringent requirements of streaming workloads. It provides the ability to store an unbounded amount of data per stream using tiered storage while being elastic, durable and consistent. Both the write and read paths of Pravega have been designed to provide low latency along with high throughput for event streams in addition to features such as long-term retention and stream scaling. Pravega provides an append-only write path to multiple partitions (referred to as segments) concurrently. For reading, Pravega is optimized for both low latency sequential reads from the tail and high throughput sequential reads of historical data.

Supported Devices and Interfaces

Pravega Sensor Collector supports the following devices:

  • ST Micro lng2dm 3-axis Femto accelerometer, directly connected via I2C
  • Linux network interface card (NIC) statistics (byte counters, packet counters, error counters, etc.)
  • Phase IV Leap Wireless Gateway
  • Generic CSV file import
  • OPC UA Client

About this Guide

In the instructions that follow, the host where you should run each command.

  • build-host: This is the host that you will use to build the installer archive.
  • gw1: This is the host that will run Pravega Sensor Collector.
  • edge1: This is the first host that is running the Pravega cluster. This may be a node running Streaming Data Platform (SDP).

Obtain the Installation Archive

Use either of the following methods to obtain the installation archive.

Download the Installation Archive

  1. Visit https://github.com/pravega/pravega-sensor-collector/releases.

  2. Download the latest version of pravega-sensor-collector-*.tgz.

Build the Installation Archive

This must be executed on a build host that has Internet access. This will download all dependencies and create a single archive that can be copied to an offline system.

  1. On the build host, build the installation archive.

    user@build-host:~$
    sudo apt-get install openjdk-11-jdk
    git clone https://github.com/pravega/pravega-sensor-collector
    cd pravega-sensor-collector
    scripts/build-installer.sh

    This will create the installation archive pravega-sensor-collector/build/distributions/pravega-sensor-collector-${APP_VERSION}.tgz.

Installation

Configuration Overview

Pravega Sensor Collector is conveniently configured using only environment variables. This avoids the need to manage site-specific configuration files and allows a simple shell script to be used to customize the configuration. All environment variables and properties begin with the prefix PRAVEGA_SENSOR_COLLECTOR.

For a list of commonly-used configuration values, see the sample configuration files.

Sample configuration properties

Configuration Parameter Value Description
CREATE_SCOPE false Boolean value.
ROUTING_KEY routingkey1 Pravega routing key
ENABLE_PRAVEGA true Boolean parameter. Default value = true
pravega_client_auth_method Bearer Authentication type to connect to Pravega client
pravega_client_auth_loadDynamic true Boolean parameter. Default value = true
KEYCLOAK_SERVICE_ACCOUNT_FILE /opt/Pravega-sensor-collector/PSC_Files/keycloak-project1.json Path for keycloak service account file
PRAVEGA_SENSOR_COLLECTOR_ACCEL2_CLASS Raw File: io.pravega.sensor.collector.file.rawfile.RawFileIngestService
CSV file: io.pravega.sensor.collector.file.csvfile.CsvFileIngestService
Parquet file: io.pravega.sensor.collector.file.parquet.ParquetFileIngestService
Pravega sensor collector class package
PRAVEGA_SENSOR_COLLECTOR_RAW1_FILE_SPEC /opt/Pravega-sensor-collector/files1 The application reads files for processing from a specified directory path
PRAVEGA_SENSOR_COLLECTOR_RAW1_FILE_EXTENSION parquet Types of file Example:-
Raw File: parquet
CSV file: csv
Parquet file: parquet
PRAVEGA_SENSOR_COLLECTOR_RAW1_DATABASE_FILE /opt/Pravega-sensor-collector/PSC_Files/datafile.db Directory path where database file gets created Example: /opt/database/databasefile.db
PRAVEGA_SENSOR_COLLECTOR_RAW1_PRAVEGA_CONTROLLER_URI tls://pravega-controller.foggy-nelson.ns.sdp.hop.lab.emc.com:443 Pravega controller URI EX: Pravega Controller URI
PRAVEGA_SENSOR_COLLECTOR_RAW1_SCOPE scope1 Scope name for Pravega sensor collector
PRAVEGA_SENSOR_COLLECTOR_RAW1_STREAM stream1 Stream name for Pravega sensor collector
PRAVEGA_SENSOR_COLLECTOR_RAW1_ROUTING_KEY routingkey1 Routing key for Pravega Sensor collector
PRAVEGA_SENSOR_COLLECTOR_RAW1_DELETE_COMPLETED_FILES false If true, PSC immediately delete the file soon after processing
PRAVEGA_SENSOR_COLLECTOR_RAW1_TRANSACTION_TIMEOUT_MINUTES 2.0 Timeout for each transaction. Default value is 2 minutes
PRAVEGA_SENSOR_COLLECTOR_RAW1_CREATE_SCOPE false If Pravega is on SDP, set this to false. Accept Boolean value.
HADOOP_HOME ${HOME}/dev For windows, Hadoop requires native libraries on Windows to work properly. You can download Winutils.exe to fix this.
See here. Add the location of bin/winutils.exe in the parameter HADOOP_HOME.
This is required only for Parquet file type not for CSV and Raw file ingestion type

Install the Service

  1. The only prerequisite on the target system is Java 11. On Ubuntu, this can be installed with:

    admin@gw1:~$
    sudo apt-get install openjdk-11-jre
  2. Copy the installation archive to the target system in /tmp.

  3. Extract the archive.

    admin@gw1:~$
    sudo mkdir -p /opt/pravega-sensor-collector
    sudo tar -C /opt/pravega-sensor-collector --strip-components 1 \
       -xzvf /tmp/pravega-sensor-collector-*.tgz
  4. Create the configuration file, starting from a sample configuration file. Start with the sample configuration file that is most similar to your environment. See the sample configuration files.

    admin@gw1:~$
    sudo cp /opt/pravega-sensor-collector/conf/env-sample-network.sh /opt/pravega-sensor-collector/conf/env-local.sh
  5. Edit the configuration file /opt/pravega-sensor-collector/conf/env-local.sh.

    admin@gw1:~$
    sudo nano /opt/pravega-sensor-collector/conf/env-local.sh
  6. At a minimum, you will need to change the following fields:

    1. PRAVEGA_SENSOR_COLLECTOR_NET1_PRAVEGA_CONTROLLER_URI: This should have the value tls://pravega-controller.${sdp_domain_name}:443, replacing ${sdp_domain_name} with the corresponding value in env.yaml.

    2. PRAVEGA_SENSOR_COLLECTOR_NET1_CREATE_SCOPE: If Pravega is on SDP, set this to false.

  7. Install and start as a Systemd service.

    admin@gw1:~$
    sudo /opt/pravega-sensor-collector/bin/install-service.sh
    

Configure Keycloak Credentials

Keycloak is used to authenticate to Pravega on Streaming Data Platform (SDP).

  1. Run the command below on the first SDP host to obtain the Keycloak credentials, which is a JSON object. Set the NAMESPACE variable to the name of your SDP project.

    edge@edge1:~$
    NAMESPACE=edge
    kubectl get secret ${NAMESPACE}-ext-pravega -n ${NAMESPACE} -o jsonpath="{.data.keycloak\.json}" | base64 -d ; echo
  2. On the target, copy the Keycloak credentials to the file /opt/pravega-sensor-collector/conf/keycloak.json.

    admin@gw1:~$
    sudo nano /opt/pravega-sensor-collector/conf/keycloak.json

Using a Private TLS Certificate Authority

If the TLS Certificate Authority (CA) used by Pravega is not trusted by a well-known public CA, such as Let's Encrypt, you must import the CA certificate.

  1. Copy the CA certificate to the target system.
    edge@edge1:~/desdp$
    scp ~/desdp/certs/* admin@gw:
    OR
    kubectl get secret pravega-controller-tls -n nautilus-pravega -o jsonpath="{.data.tls\.crt}" | base64 --decode > ~/pravega.crt
    kubectl get secret keycloak-tls -n nautilus-system -o jsonpath="{.data.tls\.crt}" | base64 --decode > ~/keycloak.crt
    kubectl get secret pravega-tls -n nautilus-pravega -o jsonpath="{.data.tls\.crt}" | base64 --decode > ~/pravegaAll.crt
    
  2. On the target system, add the CA certificate to the operating system.
    admin@gw1:~$
    sudo /opt/pravega-sensor-collector/bin/import-ca-certificate.sh ~/*.crt

Update Hosts File

If DNS is not configured throughout your network, you may need to edit the /etc/hosts file manually as described in this section.

  1. On the first SDP host, run the following commands to obtain the correct IP addresses for the required FQDNs.

    edge@edge1:~/desdp$
    SDP_DOMAIN=sdp.sdp-demo.org
    echo $(dig +short keycloak.${SDP_DOMAIN})                                 keycloak.${SDP_DOMAIN} ; \
    echo $(dig +short pravega-controller.${SDP_DOMAIN})                       pravega-controller.${SDP_DOMAIN} ; \
    echo $(dig +short nautilus-pravega-segment-store-0.pravega.${SDP_DOMAIN}) nautilus-pravega-segment-store-0.pravega.${SDP_DOMAIN}
  2. Ensure that the previous command returned an IP address for each host name. For example:

    10.42.0.10 keycloak.sdp.cluster1.sdp-demo.org
    10.42.0.10 pravega-controller.sdp.cluster1.sdp-demo.org
    10.42.0.12 nautilus-pravega-segment-store-0.pravega.sdp.cluster1.sdp-demo.org
    
  3. On the target device, add the output from the previous command to the end of the file /etc/hosts.

    admin@gw1:~$
    sudo nano /etc/hosts

Maintain the Service

  1. Restart the service.

    admin@gw1:~$
    sudo systemctl restart pravega-sensor-collector.service
  2. View the status of the service.

    admin@gw1:~$
    sudo systemctl status pravega-sensor-collector.service
    sudo journalctl -u pravega-sensor-collector.service -n 1000 --follow
    

Running as a Windows Service

  1. Download winsw.exe from https://github.com/winsw/winsw/releases and rename it as PravegaSensorCollectorApp.exe. Save it in the same folder as PravegaSensorCollectorApp.xml.

  2. Modify PravegaSensorCollectorApp.xml. Check PRAVEGA_SENSOR_COLLECTOR_RAW1_PRAVEGA_CONTROLLER_URI.

  3. Add the path to the jar file pravega-sensor-collector/build/libs/pravega-sensor-collector-${APP_VERSION}.jar generated by build-installer.sh in PravegaSensorCollectorApp.xml.

  4. Install and run the service using following commands:

    PravegaSensorCollectorApp.exe install 
    PravegaSensorCollectorApp.exe start 
    PravegaSensorCollectorApp.exe restart 
    PravegaSensorCollectorApp.exe status
    PravegaSensorCollectorApp.exe stop 
    PravegaSensorCollectorApp.exe uninstall 
    

    The logs for the sensor collector wil be available under windows-service/PravegaSensorCollectorApp.wrapper.log If there are any errors during service execution, the error log will be in windows-service/PravegaSensorCollectorApp.out.log

Data File Ingestion

Overview

Pravega Sensor Collector can be configured to read data from files and write the data to Pravega.

Periodically, new files that match the file name pattern in LOG_FILE_INGEST_FILE_SPEC will be identified and ingested. The names of files can be in any format. When multiple files match the file name pattern, the files will be ingested in alphabetical order. For this reason, it is important that the file names are generated in alphabetical order. This can be done by using a zero-padded counter (e.g. 0000000001.csv, 0000000002.csv, ...) or a timestamp (2020-07-29-16-00-02.123.csv).

It is assumed that files matching the pattern are immediately readable in their entirety. For this reason, it is critical that ingested files are created atomically. This can be accomplished by writing to a file with a ".tmp" extension and then renaming it to have a ".csv" extension after the file has been written in its entirety.

After being durably saved to the Pravega stream, the files will be deleted. This can be disabled by setting LOG_FILE_INGEST_DELETE_COMPLETED_FILES to false.

Each instance of Pravega Sensor Collector will have a unique writer ID. The writer ID will be a UUID that is generated the first time the instance starts. The writer ID will be persisted to a local SQLite database file and subsequent executions will use the same writer ID.

The SQLite database stores the writer ID and the list of files being ingested. SQL transactions are used to ensure database consistency even in the event of failures.

CSV files are deleted only after flushing events to Pravega.

Pravega Sensor Collector is installed as a Linux systemd service. Systemd will start the service when the system boots up and it will restart the service if it fails.

Supported File Formats

CSV

CSV files must have exactly one header. There are no other restrictions on the CSV file. Data from multiple rows will be combined to efficiently produce events in JSON format. When possible, integers and floating point values will be converted to their corresponding JSON data types.

Each JSON object may have additional static fields. These can be defined in the parameter LOG_FILE_INGEST_EVENT_TEMPLATE which accepts a JSON object.

Write Sample Events

Edit the configuration file /opt/pravega-sensor-collector/conf/env-local.sh (See env-sample-telit.sh for a sample configuration)

If using the CSV file driver, you can simulate the functionality of it by using the procedure in this section.

  1. On the target device, create the file named /opt/dw/staging/Accelerometer.0000000001.tmp.

    admin@gw1:~$
    cd /opt/dw/staging
    sudo nano Accelerometer.0000000001.tmp
  2. Copy and paste the following contents, then save and exit:

    "T","X","Y","Z"
    "2020-08-19 19:35:44.029","0.458949","9.637929","0.611932"
    "2020-08-19 19:35:44.031","0.458949","9.484945","0.611932"
    "2020-08-19 19:35:44.033","0.458949","9.637929","0.611932"
    "2020-08-19 19:35:44.035","0.611932","9.484945","0.611932"
    
  3. Rename the file to have a .csv extension. (This must be an atomic operation.)

    admin@gw1:~$
    sudo mv Accelerometer.0000000001.tmp Accelerometer.0000000001.csv
  4. If you have deployed Flink Tools, within 2 minutes, on the SDP host, you should see the sample events written to the directory /desdp/lts/edge-data-project-pvc-*/streaming-data-platform/$(hostname)/sensors-parquet/.

Raw file

Raw file data can be ingested in byte array format. Each file is sent as a single event.

The script run-with-gradle-raw-file.sh can be edited for testing. Make sure PRAVEGA_SENSOR_COLLECTOR_RAW1_FILE_SPEC is set correctly. This is where the files will be read from.

Parquet

Parquet data is parsed to efficiently produce events in JSON format. When possible, integers and floating point values will be converted to their corresponding JSON data types.

The script run-with-gradle-parquet-files-ingest.sh can be edited for testing.

Note: For windows, Hadoop requires native libraries on Windows to work properly. You can download Winutils.exe to fix this. See here. Add the location of bin/winutils.exe in the parameter HADOOP_HOME.

Phase IV Leap Wireless Gateway Integration

Edit the configuration file /opt/pravega-sensor-collector/conf/env-local.sh (See env-sample-leap.sh for a sample configuration)

The following are example records that are written to the Pravega stream.

{"deviceId":"000072FFFEF0000","readingTimestamp":"2021-11-24T18:42:23Z","receivedTimestamp":"2021-11-24T18:42:33.649728Z","values":[{"componentIndex":0,"sensorIndex":0,"valueIndex":0,"sensorValueDefinitionId":7,"value":23.88,"status":"Success","label":"Temperature  ","iconUrl":"/images/Thermometer_16x16.png","units":""},{"componentIndex":0,"sensorIndex":0,"valueIndex":1,"sensorValueDefinitionId":8,"value":23.87,"status":"Success","label":"Temperature Weighted Average ","iconUrl":"/images/Thermometer_16x16.png","units":""},{"componentIndex":0,"sensorIndex":1,"valueIndex":0,"sensorValueDefinitionId":9,"value":1,"status":"Success","label":"Door Status (Open / Closed)","iconUrl":"/images/Switch_16x16.png","units":""},{"componentIndex":0,"sensorIndex":1,"valueIndex":1,"sensorValueDefinitionId":10,"value":0,"status":"Success","label":"Door Open Time (sec)","iconUrl":"/images/Clock_16x16.png","units":""}]}
{"deviceId":"000072FFFEF0000","readingTimestamp":"2021-11-24T18:40:23Z","receivedTimestamp":"2021-11-24T18:42:33.649728Z","values":[{"componentIndex":0,"sensorIndex":0,"valueIndex":0,"sensorValueDefinitionId":7,"value":23.88,"status":"Success","label":"Temperature  ","iconUrl":"/images/Thermometer_16x16.png","units":""},{"componentIndex":0,"sensorIndex":0,"valueIndex":1,"sensorValueDefinitionId":8,"value":23.87,"status":"Success","label":"Temperature Weighted Average ","iconUrl":"/images/Thermometer_16x16.png","units":""},{"componentIndex":0,"sensorIndex":1,"valueIndex":0,"sensorValueDefinitionId":9,"value":1,"status":"Success","label":"Door Status (Open / Closed)","iconUrl":"/images/Switch_16x16.png","units":""},{"componentIndex":0,"sensorIndex":1,"valueIndex":1,"sensorValueDefinitionId":10,"value":0,"status":"Success","label":"Door Open Time (sec)","iconUrl":"/images/Clock_16x16.png","units":""}]}

Linux network interface card (NIC) statistics

Edit the configuration file /opt/pravega-sensor-collector/conf/env-local.sh (See env-sample-network.sh for a sample configuration)

To get PRAVEGA_SENSOR_COLLECTOR_NET1_NETWORK_INTERFACE value

admin@gw1:~$
ls /sys/class/net/

OPC UA Client

Edit the configuration file /opt/pravega-sensor-collector/conf/env-local.sh (See env-sample-opcua.sh for a sample configuration)

To Simulate use OPC UA Servers like Kepware or opensource servers opc-ua-demo-server

Troubleshooting

Logging

You can adjust the logging level by editing the environment variable JAVA_OPTS and adding -Droot.log.level=DEBUG. The default level is INFO.

For example:

export JAVA_OPTS="-Xmx512m -Droot.log.level=DEBUG"

Development Tips

This information may be useful for developers.

Configuration for Debugging

For convenience when debugging in an IDE, configuration values can also be specified in a properties file. To use a properties file, you must set the environment variable PRAVEGA_SENSOR_COLLECTOR_PROPERTIES_FILE to the path of the properties file.

Adding Additional Devices

To add support for additional types of devices, you should create a subclass of SimpleDeviceDriver.java and implement the methods readRawData, createSamples, decodeRawDataToSamples, and serializeSamples. Refer to the implementation of NetworkDriver.java as a guide.

Start Pravega Server

admin@gw1:~$
cd
git clone https://github.com/pravega/pravega
cd pravega
git checkout r0.12
./gradlew startStandalone \
  -Dcontroller.transaction.lease.count.max=2592000000 \
  -Dcontroller.transaction.execution.timeBound.days=30

Start Leap API Mock Server

To run the leap mock server

admin@gw1:~$
./gradlew pravega-sensor-collector::runLeapAPIMockServer

Start Pravega Sensor Collector

admin@gw1:~$
PRAVEGA_SENSOR_COLLECTOR_PROPERTIES_FILE=src/test/resources/LeapTest.properties \
./gradlew pravega-sensor-collector::run

View the SQLite Database

admin@gw1:~$
docker run --rm -it -v /tmp/leap1.db:/tmp/leap1.db keinos/sqlite3 sqlite3 /tmp/leap1.db .dump

Release Procedure

Committers of the project should use the following procedure to release a new version.

  1. Increment APP_VERSION in scripts/env.sh.

  2. Commit the changes to the master branch using the normal Github pull request procedure.

  3. git tag v0.2.14

  4. git push --tag

  5. Open https://github.com/pravega/pravega-sensor-collector/releases and publish the draft release.

References

About

Pravega Sensor Collector is 100% open source and community-driven. All components are available under Apache 2 License on GitHub.